Sensors & Software LMX100 Bedienungsanleitung

LMX Does Not Power Up or LMX Sensor Not Detected

If you have connected the cables to the LMX Sensor, Display Unit, and the battery, pressed the

Power button on the Display Unit and:

•The Display Unit does not power up, or

•The LMX Sensor is not detected, and you get the following messages:

1) Wait at least 1-minute and see if the Display Unit starts up. Sometimes the Power LED on the

Display Unit fails but the Display Unit is otherwise OK. If the application starts but the LED on

the Display Unit does not turn on, test the operation of the LED using the System Test >

Keypad test under Tools.

2) Test the battery

a) Check that the fuse, inside the battery case, has not blown. If so, replace the 10 Amp

fuse with one of the spare fuses inside the battery case.

b) Use a multimeter with fine tipped probes (1mm or 0.04 inches) to measure the battery

voltage at the connector on the outside of the battery case. Measure the voltage between

socket #1 (ground, using the black probe) and socket #4 (power, using the red probe). If

the voltage is less than 10.5 volts, there is a problem with the battery.

3) Test the Battery Cable

Insert the battery cable into the battery and test the battery cable. Use a multimeter to

measure the battery voltage at the connector at the end of the battery cable. Measure the

voltage between socket #1 (ground, using the black probe) and socket #4 (power, using

the red probe). If the voltage is less than 10.5 volts, there is a problem with the battery

cable.

4) Check the LMX Sensor and Display Unit Connectors

Turn off the LMX system and disconnect the battery before disconnecting the cable that

connects the Display Unit to the LMX Sensor.

a) On the back of the Display Unit, check that none of the 37 pins are missing, bent, or

recessed. Look at the pins on an angle to confirm they are all flush with one another.

If one is bent or recessed, gently bend the pin back straight and flush with the other

pins. Then reconnect the cable and try powering the LMX system again.

b) Check all 37 sockets at the LMX connector, ensuring that none are blocked with debris.

If so, clean out the debris, reconnect the cable and try powering the system again.

5) Replace the Cable

If you have a spare cable, replace the current cable. If the system does not power on

or if the LMX Sensor is not detected with either cable, please contact your GPR

supplier for further assistance.

6) Test the Cable

a) On the end of the cable that connects to the LMX Sensor, check that none of the 37 pins

are missing, bent, or recessed. Look at the pins on an angle to confirm they are all flush

with one another. If one is bent or recessed, gently bend the pin back straight and flush

with the other pins. Connect the cable to the LMX Sensor and try powering the LMX

system again.

b) Disconnect the end of the cable that connects to the back of the Display Unit.

c) Check all 37 sockets at the end of the cable, ensuring that none are blocked with debris.

If so, clean out the debris, reconnect the cable and try powering the Display Unit again.

d) With the cable connected to the LMX Sensor and the battery connected to the system,

check the power from the battery is reaching the Display Unit through the cable by using a

multimeter to measure the voltage between socket #21 (ground, using the black probe)

and sockets #1 or #2 (power, using the red probe) on the end of the cable. If the voltage

is zero, there may be a problem with the cable. If the voltage is at least 10.5 volts, the

problem may be the Display Unit. Please contact your GPR supplier for further assistance.

Display Unit Screen turns White After Powering Up

If the Display Unit screen turns completely white after powering up the system, the battery does not

have enough voltage to completely power the system. Recharge or replace the battery

Andere Handbücher für LMX100

Inhaltsverzeichnis

Andere Sensors & Software Radar Handbücher

Sensors & Software

Sensors & Software pulseEKKO Pro Bedienungsanleitung

Sensors & Software

Sensors & Software CONQUEST 100 Bedienungsanleitung

Sensors & Software

Sensors & Software Noggin 100 Bedienungsanleitung

Sensors & Software

Sensors & Software Conquest Series Bedienungsanleitung

Sensors & Software

Sensors & Software pulseEKKO Bedienungsanleitung

Sensors & Software

Sensors & Software LMX200 Series Bedienungsanleitung

Beliebte Radar Handbücher anderer Marken

SAW D2L

SAW D2L Valentine One Gen2 Bedienungsanleitung

Raymarine

Raymarine Raytheon R20X Bedienungsanleitung

Simrad

Simrad CA34 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot FMR67B Technische Daten

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Bedienungsanleitung

ECHOMAX

ECHOMAX Active-X-Band Bedienungsanleitung

AGD

AGD 340 Bedienungsanleitung

Kustom Signals

Kustom Signals Eagle 3 Bedienungsanleitung

SYMEO

SYMEO STU Bedienungsanleitung

Axis

Axis D2110-VE Bedienungsanleitung

MALA

MALA MIRA Bedienungsanleitung

Emerson

Emerson ROSEMOUNT 5300 Bedienungsanleitung

Rosemount

Rosemount 5300 Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex FMP56 Technische Daten

TERMA

TERMA SCANTER 5102 Bedienungsanleitung

GSSI

GSSI UtilityScan Bedienungsanleitung

Acconeer

Acconeer A111 Bedienungsanleitung

Crosley

Crosley CR37 Bedienungsanleitung