Sesamo Icon Bedienungsanleitung
2 (SUMMARY)
Sesamo - Icon
EN
SUMMARY
SUMMARY.............................................................................................................................................................................2
GENERAL INFORMATION - INSTALLATION AND WIRING.....................................................................................................3
KEY FUNCTIONS - LED INDICATIONS.....................................................................................................................................5
FUNZIONALITÀ BASE - LOGICHE ...........................................................................................................................................6
FUNCTIONALITY - SERVICE KEYS...........................................................................................................................................7
PROGRAMMING MODES ......................................................................................................................................................8
TRASPONDER FUNCTIONALITY...........................................................................................................................................12
MICRO-USB FUNCTIONALITY ..............................................................................................................................................19
3 (SUMMARY)
Sesamo - Icon
EN
GENERAL INFORMATION - INSTALLATION AND WIRING
The "ICON" selector was created to work with all SESAMO operators, designed to be used both by the user for
managing the door functionality and by the installer for adjusting the basic parameters of the door.
ICON must be installed inside of buildings.
H=118mm
B=81mm
SP=18mm
5 (SUMMARY)
Sesamo - Icon
EN
KEY FUNCTIONS - LED INDICATIONS
•To activate a logic / programming / choice, place your finger inside the key area indicated with a rectangle
•Keep your finger resting 1 second
•The LEDs next to the key areas indicate, if fixed, that the logic has been set correctly.
•The LEDs, if flashing, may have various indications based on the action you want to perform (they will be
explained in the various paragraphs dedicated to the selector functions).
•The icon with the battery drawn and a LED in the center indicates:
oif it is fixed that the automation is battery powered
oif flashing that the batteries may be flat, malfunctioning or with a possible anomaly.
•The Micro - usb icon indicates the presence of a micro - usb port. To gain access, remove the upper body of the
selector applied by interlocking.
Led batteries
Key
Led
Transponder functionality area
Icon Micro-usb
6 (SUMMARY)
Sesamo - Icon
EN
FUNZIONALITÀ BASE - LOGICHE
List of logics available:
1. 2 Radar (automatic)
2. 1 Radar (only exit)
3. Stop open
4. Stop close
5. Manual
Actions to be performed in order to set the chosen logic:
1. Place your finger in the desired key area for 1 second.
2. You will hear 1 beep.
3. The LED will turn on steadily
4. Logic is set.
7 (SUMMARY)
Sesamo - Icon
EN
FUNCTIONALITY - SERVICE KEYS
Read the warnings carefully!!!!
RESET - by placing the finger for 3 seconds, a reset command is confirmed to the main board
For sliding: by placing your finger (1 beep plus fixed LED) I link the "partial opening" logic to the logic
previously preset (on the selector I will find two LEDs lit, one on the logic and the other on the
snowflake icon)
For swing: not used
1. In case of partial opening selection with Stop
open logic already active, it will be necessary
to let the automation perform a complete
opening cycle to make the partial opening
settings active.
2. In case of Reset, partial opening is disabled,
unless a logic after reset (with Digidor) has
been set already.
3. The stop close logic is the only logic that
cannot be combined with partial opening.
8 (SUMMARY)
Sesamo - Icon
EN
PROGRAMMING MODES
To be able to enter programming mode:
PR+ESC at the same time:
placing your fingers on the two keys at the same time for more than 3 ”(1 beep as an indication) you
enter the programming menu of the selector from where you can adjust some basic parameters. (see
list with relative sequence explained below).
ATTENTION!!!
I understand that I have entered the programming menu because all the LEDs are flashing.
9 (SUMMARY)
Sesamo - Icon
EN
Sequence for setting parameters:
At this stage they are inside programming and all LEDs are flashing - choose the parameter to be set by placing your
finger on the corresponding button.
Once the parameter to be adjusted has been chosen, the lit LEDs will indicate the adjustment level (1 minimum - 5
maximum - see tables for automation references / values). By placing your finger on the button, I increase (if the LED is
not on) or decrease (if the LED is on) the adjustment level
1 –Opening speed
2 –Closing speed
3 –Idle time
4 –% Partial opening
SLIDING
5 –Anti-crashing
SLIDING
Minimum value
4 –Anti-crashing
in opening - SWING
5 –Anti-crashing
in closing - SWING
Maximum value
10 (SUMMARY)
Sesamo - Icon
EN
After adjusting the selected parameter to be able to store the adjustment:
In case you do not want to memorize the adjusted parameter:
By placing your finger once
I STORE ONLY THE SETTING
SET, I automatically return to
the parameter selection mode
(to be able to choose and set
another parameter if
necessary).
By placing your finger once
I EXIT WITHOUT SETTING,
I automatically return to the
parameter selection mode (to
be able to choose and set
another parameter if
necessary).
Placing the finger a
second time I ACTIVATE
THE SET VALUES and go
back to the logic selection
Placing the finger, a second
time I RETURN TO THE
LOGIC SELECTION
WITHOUT ACTIVATING
ANYTHING
1° press
2° press
1° press
2° press
Inhaltsverzeichnis
