Sewhacnm SI Digital Indicator Series Bedienungsanleitung

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

1 / 22

SEWHA CNM CO., LTD

SI Digital Indicator Series

Support version

V3.0 and over

XDesignerPlus

2.1.0.0 and over

CONTENTS

Thank you for using TOP series of M2I corporation.

Please read this manual carefully to know connection methods and

procedures of “TOP to External device”.

1. System configuration

Page 2

A section for showing connectable external devices, serial signal

types, connection configurations. Refer this section to select the

right system configuration.

2. Selection of TOP, External device

Page 3

A section for selecting a Top model and the external device.

3. Example of system setting

Page 4

A section for explaining examples to connect communications of

TOP to External Device.

Select the correct example in your case according to “1. System

configuration”

4. Communication setting

Page 8

A section for Communication setting.

The setting should be the same with the external device.

5. Cable diagram

Page 11

A section for cable to connect to external device.

Select a suitable cable diagram for your system.

6. Usable address

Page 13

A section for usable address to communicate with external

device.

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

2 / 22

1. System configuration

System configurations of TOP and “SEWHA CNM –SI Digital Indicator Series”

Indicator Model

Link I/F

Com type

Setting system

Cable

SI 580

SI 480

RS232C I/F

(D-sub 9 pin)

RS–232C

3.1 setting ex 1

( Page 4 )

5.1 Cable diagram 1

(Page 11 )

RS232C I/F

(Terminal Block 3 pin)

RS–232C

3.1 setting ex 1

(Page 4 )

5.2 Cable diagram 2

(Page 11 )

RS485 I/F

(Terminal Block 4 pin)

RS–485

(2 wire)

3.2 setting ex 2

(Page 6 )

5.3 Cable diagram 3

(Page 12 )

SI 4500

SI 4410

SI 4400

SI 4300

SI 4200

SI 4100

SI 4010

SI 4000

RS232C I/F

(D-sub 9 pin)

RS–232C

3.3 setting ex 3

(Page 4 )

5.1 Cable diagram 1

(Page 11 )

RS232C I/F

(Terminal Block 3 pin)

RS–232C

3.3 setting ex 3

(Page 4 )

5.2 Cable diagram 2

(Page 11 )

RS485 I/F

(Terminal Block 4 pin)

RS–485

(2 wire)

3.4 setting ex 4

(Page 6 )

5.3 Cable diagram 3

(Page 12 )

■Connection configuration

ㆍ1 : 1(TOP 1 unit to External device 1 unit) connection –It is available with RS232C/422/485.

ㆍ1 : N(TOP 1 unit to External device N unit) connection –It is available with RS422/485.

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

3 / 22

2. Selection of TOP, External device.

Select a external device which is communicated to the TOP..

Setting Items

Description

TOP

Series

Select a TOP series which is communicated with the external device.

Install a OS file v3.1 as diagram below before download a project file you have made.

Series

OS version

XTOP / HTOP

V3.1

Name

Select a TOP model which is communicated with the external device.

External

Device

Vendor

Select vendor of the external device which is communicated with the TOP.

Select “SEWHA CNM”.

PLC

Select a model name of the external device which is communicated with the TOP.

Select “SI Digital Indicator Series”.

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

4 / 22

3. Example of system setting

Set setting of communication interface of TOP and SI Digital Indicator Series.

3.1 Example 1

Set your system as below.

Item

TOP

“SI Digital Indicator Series”

Serial Signal Level (port/channel)

RS-232C

User set

Station number(Instrument Address)

─

User set

Serial Baud rate

[BPS]

9600

User set

Serial data bit

[Bit]

User set

Serial stop bit

[Bit]

User set

Serial parity bit

[Bit]

NONE

User set

(1) XDesignerPlus setting

Set [project property] of XDesignerPlus as below and download it to TOP..

■[Project > Project property > project > TOP Setting > TOP’s Name]

Set communication interface of TOP.

■External device setup

Set [PLC Comm. Info] of SI Digital Indicator Series.

-Equipment No.: Number of external device.

-Series : Select the name of external device.

(2) External device setup

Set the Menu of “F-FUNCTION”as below by the keys of front panel and reboot external device after setting.

If you need details of setting, please read manual of external device.

(1) Communication/Extended mode “SI Digital Indicator Series”of are both available to use.

This section explains about setting of communication mode.

(2) .If a loadcell is not connected to a indicator, the indicator does not operate and the communication

is not operated, too.

1. Set “F-FUNCTION”as below.

F-FUNCTION

Setting

Descriptions

Remarks

F18

Select “Instrument No.”of the indicator.

–

F30

Data bit : 8 bit, Stop bit : 1 bit, Parity bit : None

–

F31

9600 bps

–

F32

Command Mode

necessary

F34

Check sum Command Mode is set disable.

necessary

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

5 / 22

3.2 Example 2

Set your system as below.

Item

TOP

“SI Digital Indicator Series”

Serial Signal Level (port/channel)

RS-485 (COM2)

RS-485

User set

Station number(Instrument Address)

─

User set

Serial Baud rate

[BPS]

9600

User set

Serial data bit

[Bit]

User set

Serial stop bit

[Bit]

User set

Serial parity bit

[Bit]

NONE

User set

(1) XDesignerPlus setting

Set [project property] of XDesignerPlus as below and download it to TOP..

■[Project > Project property > project > TOP Setting > TOP’s Name]

Set communication interface of TOP.

■External device setup

Set [PLC Comm. Info] of SI Digital Indicator Series.

-Equipment No.: Number of external device.

-Series : Select the name of external device.

(2) External device setup

Set the Menu of “F-FUNCTION”as below by the keys of front panel and reboot external device after setting.

If you need details of setting, please read manual of external device.

(1) Communication/Extended mode “SI Digital Indicator Series”of are both available to use.

This section explains about setting of communication mode.

(2) .If a loadcell is not connected to a indicator, the indicator dose not operate and the communication

is not operated, too.

1. Set “F-FUNCTION”as below.

F-FUNCTION

Setting

Descriptions

Remarks

F18

Select “Instrument No.”of the indicator.

–

F30

Data bit : 8 bit, Stop bit : 1 bit, Parity bit : None

–

F31

9600 bps

–

F32

Command Mode

necessary

F34

Check sum Command Mode is set disable.

necessary

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

6 / 22

3.3 Example 3

Set your system as below.

Item

TOP

“SI Digital Indicator Series”

Serial Signal Level (port/channel)

RS-232C

User set

Station number(Instrument Address)

─

User set

Serial Baud rate

[BPS]

9600

User set

Serial data bit

[Bit]

User set

Serial stop bit

[Bit]

User set

Serial parity bit

[Bit]

NONE

User set

(1) XDesignerPlus setting

Set [project property] of XDesignerPlus as below and download it to TOP..

■[Project > Project property > project > TOP Setting > TOP’s Name]

Set communication interface of TOP.

■External device setup

Set [PLC Comm. Info] of SI Digital Indicator Series.

-Equipment No.: Number of external device.

-Series : Select the name of external device.

(2) External device setup

Set the Menu of “F-FUNCTION”as below by the keys of front panel and reboot external device after setting.

If you need details of setting, please read manual of external device.

(1) Communication/Extended mode “SI Digital Indicator Series”of are both available to use.

This section explains about setting of communication mode.

(2) .If a loadcell is not connected to a indicator, the indicator dose not operate and the communication

is not operated, too.

1. Set “F-FUNCTION”as below.

F-FUNCTION

Setting

Descriptions

Remarks

F18

Select “Instrument No.”of the indicator.

–

F30

Data bit : 8 bit, Stop bit : 1 bit, Parity bit : None

–

F31

9600 bps

–

F32

Command Mode

necessary

F34

Check sum Command Mode is set disable.

necessary

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

7 / 22

3.4 Example 4

Set your system as below.

Item

TOP

“SI Digital Indicator Series”

Serial Signal Level (port/channel)

RS-485 (COM2)

RS-485

User set

Station number(Instrument Address)

─

User set

Serial Baud rate

[BPS]

9600

User set

Serial data bit

[Bit]

User set

Serial stop bit

[Bit]

User set

Serial parity bit

[Bit]

NONE

User set

(1) XDesignerPlus setting

Set [project property] of XDesignerPlus as below and download it to TOP..

■[Project > Project property > project > TOP Setting > TOP’s Name]

Set communication interface of TOP.

■External device setup

Set [PLC Comm. Info] of SI Digital Indicator Series.

-Equipment No.: Number of external device.

-Series : Select the name of external device.

(2) External device setup

Set the Menu of “F-FUNCTION”as below by the keys of front panel and reboot external device after setting.

If you need details of setting, please read manual of external device.

(1) Communication/Extended mode “SI Digital Indicator Series”of are both available to use.

This section explains about setting of communication mode.

(2) .If a loadcell is not connected to a indicator, the indicator dose not operate and the communication

is not operated, too.

1. Set “F-FUNCTION”as below.

F-FUNCTION

Setting

Descriptions

Remarks

F18

Select “Instrument No.”of the indicator.

–

F30

Data bit : 8 bit, Stop bit : 1 bit, Parity bit : None

–

F31

9600 bps

–

F32

Command Mode

necessary

F34

Check sum Command Mode is set disable.

necessary

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

8 / 22

4. Communication setting

Communication setting can be set on XDesignerPlus or TOP Main Menu. The setting should be the same with the external device.

4.1 XDesignerPlus setup

Set [project property] of XDesignerPlus as below and download it to TOP.

■[Project > Project property > project > TOP Setting > TOP’s Name]

Set communication interface of TOP..

■External device setup

Set [PLC Comm. Info] of SI Digital Indicator Series.

■Setting communication Interface

Item

Description

Serial Baud Rate

Setup [communications Baud rate] of PLC connected with COM2/1 port.

Serial Data Bit

Setup [Data Bit] of PLC connected with COM2/1 port.

Serial Stop Bit

Setup [Stop Bit] of PLC connected with COM2/1 port.

Serial Parity Bit

Setup [Parity Bit] of PLC connected with COM2/1 port.

Serial Signal Level

Setup signal level(RS-232C/422/485) of PLC connected with COM2/1 port.

Station Num. In Diag [0~31]

Setup [Station Number] (use when communications diagnosis) of PLC connected with COM2/1 port.

Time Out [ x100 mSec ]

Setup [Time Out] of PLC connected with COM2/1 port. (Timeout:: waiting time for answer of PLC)

Send Wait [ x10 mSec ]

Setup [Send Wait] of PLC connected with COM2/1 port.

(Send Wait: communicate after waiting setting time when touch screen requires communications.)

■Setting N:1 communication Interface

Item

Description

N:1 Use

Decide if use function of [N:1] function.

[N:1] is the communications between multiple Touch machines and one PLC.

If set [No], setup of No.17 and 18 below are to be ignored.

N:1 Station Number (0~31)

Setup [Station Number] when use [N:1] function.

N:1 Max Machine (2~31)

Setup number of touch machine when use [N:1] function.

■Setting external device

Item

Description

Equipment No.

Number of external device. [ 01 –99 ] ([1] is default)

Series

Select the name of external device.

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

9 / 22

4.2 Setting TOP Main Menu

[In to the Main Menu] While the power of TOP is turned on and the buzzer beeps once, Touch the

screen’s upper part under the TOP logo on the front sheet.

Note: When turn on the power while pressing the touch, it does not convert into the Menu mode.

When the buzzer sound is unable to confirm because of the noise surroundings, the power of

touch shall be allowed while continuously press and off on the lower part of the logo.

■[Main Menu > Comm. Setup]

Communication setup

1. COM2 Serial Baud Rate : 38400 [BPS]

COM 2 port

2 COM2 Serial Data Bit : 8 [BIT]

Setting communication

3 COM2 Serial Stop Bit : 1 [BIT]

Interface

4 COM2 Serial Parity Bit : NONE [BIT]

5 COM2 Serial Signal Level : RS-232C

6 COM2 Station Num. In Diag.(0~31) : 00

7 COM2 Time Out : 10 * 100 [mSec]

8 COM2 Send Wait : 00* 10 [mSec]

9 COM1 Serial Baud Rate : 38400 [BPS]

COM 1 port

10. COM1 Serial Data Bit : 8 [BIT]

Setting communication

11. COM1 Serial Stop Bit : 1 [BIT]

Interface

12. COM1 Serial Parity Bit : NONE [BIT]

13. COM1 Serial Signal Level (0~31) : 00

14. COM1 Time Out : 10 * 100 [mSec]

15. COM1 Send Wait : 00* 10 [mSec]

16. N:1 Use : No

COM 2 port

17. N:1 Station Number (0~31) : 00

Setting N:1 communication

18. N:1 Max Machine (2~31) : 02

Interface

■Setting communication Interface

Item

Description

Serial Baud Rate

Setup [communications Baud rate] of PLC connected with COM2/1 port.

Serial Data Bit

Setup [Data Bit] of PLC connected with COM2/1 port.

Serial Stop Bit

Setup [Stop Bit] of PLC connected with COM2/1 port.

Serial Parity Bit

Setup [Parity Bit] of PLC connected with COM2/1 port.

Serial Signal Level

Setup signal level(RS-232C/422/485) of PLC connected with COM2/1 port.

Time Out [ x100 mSec ]

Setup [Time Out] of PLC connected with COM2/1 port. (Timeout:: waiting time for answer of PLC)

Send Wait [ x10 mSec ]

Setup [Send Wait] of PLC connected with COM2/1 port.

(Send Wait: communicate after waiting setting time when touch screen requires communications.)

Station Num. In Diag [0~31]

Setup [Station Number] (when use communications diagnosis) of PLC connected with COM2/1 port.

■Setting N:1 communication Interface

Item

Description

N:1 Use

Decide if use function of [N:1] function.

[N:1] is the communications between multiple Touch machines and one PLC.

If set [No], setup of No.17 and 18 below are to be ignored.

N:1 Station Number (0~31)

Setup [Station Number] when use [N:1] function.

N:1 Max Machine (2~31)

Setup number of touch machine when use [N:1] function.

XDesignerPlus Ver2.0 외부 장치 접속 매뉴얼

10 / 22

4.3 Communication Diagnosis

■TOP –Check interface setting of external device and TOP

- Touch the top of screen to go into the Main Menu after reset the power of TOP.

- Check [Comm. Setup] whether it is the same of external device’s setup or not.

■Diagnosis of error of communication status

- “Diagnosis > Touch Start of “Com2 or Com1 Communication Diagnosis ”.

- A dialog box of diagnostics is showed and check Setting of TOP and external device with the communication Diagnosis Sheet

below if the dialog box shows “Time Out Error!”

OK!

The communication status is good

Time Out Error!

The communication status is error

- Error of the cable or Setting of TOP/External device

■communication Diagnosis Sheet

- If you have problems of communication of TOP/External device, check your system with the sheet below.

Subject

Contents

Check

TOP

Version information

xDesignerPlus :

O.S :

Using port

COM 2

COM 1

The name of driver

Others setting state

Station No.

Project property

Comm. diagnosis

Serial

Baud rate

[BPS]

Parameter

Data bit

[BIT]

Stop bit

[BIT]

Parity bit

[BIT]

System

configuration

Type of system connection

1:1

1:N

N:1

1:1 (RS-232C is fixed)

The name of cable connected

External

The name of CPU

Device

The name of comm.. port

(the name of module)

protocol(mode)

Station number

Others setting state

Serial

Baud rate

[BPS]

Parameter

Data bit

[BIT]

Stop bit

[BIT]

Parity bit

[BIT]

Range of available address

(6. Usable address)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sewhacnm Touchscreen Handbücher

Sewhacnm

Sewhacnm SI 400 Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung