SEWOO LK-P43 Bedienungsanleitung
All specifications are subject to change without notice
J. STEPHEN Lab., Ltd.
28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do, 18103, Republic of Korea
TEL : +82-31-8077-5000 FAX : +82-31-459-8880
http://www.miniprinter.com
P43(Peeler) Rev. H 01/18
USER’S MANUAL / Peeler
MODEL : LK-P43
1
Risk of explosion if battery is replaced by an incorrectly type.
Dispose of used battery according to the local disposal instructions.
23
Table of Contents
1. Safety Precautions 4
2.
Unpacking
6
3. Product Overview 7
4. Installation & Usage 8
4-1. Display 8
4-2. Installing the Battery 9
4-3. Removing the Battery 10
4-4. Charging the Battery 11
4-5. Battery charger usage 12
4-6. Car charger usage 13
4-7. Installing Belt Clip 14
4-8. Interface Cap Installation 15
4-9. Paper Roll Installation 16
4-10. Install / Uninstall the External Paper Guides 18
4-11. Peel Mode 20
4-12. Shoulder Strap Installation 22
4-13. Diagnostic Test 23
5. Peripherals Connection 25
5-1. Bluetooth(802.11a/b/g) Connection 25
5-1. Wi-Fi(802.11a/b/g) Connection 25
5-2. Interface Cable Connection 26
6. Printer Cleaning 27
6-1. Print-Head Cleaning 27
6-2. Platen Roller Cleaning 28
7. Printer Specication 29
7-1. Specication 29
8. CPCL Command Compatibilit
y
31
9. ESC/POS Command Compatibilit
y
34
10. ZPL Command Compatibilit
y
36
45
For better safety and reliability, adhere to the following precautionary measures.
Read and follow the instructions carefully before operation of the product.
1. Safety Precautions
WARNING
Failure to follow these instructions could result in re, electric shock,
other injuries, or property damage.
Indication
Prohibition
(Potential risk of electric shock or re)
(Potential risk of electric shock or re)
(Potential risk of electric shock or re)
(Potential risk of electric shock or re)
Must follow
Do not disassemble Unplug the power from the
outlet
Grounding to prevent electric
shock
Do not handle the product
with wet hands
Do not pull or touch the power plug with
wet hands.
Do not bend the wire and do not allow the
wire to be pinched or crushed by heavy
objects.
If a power plug is broken or a plug is cut or
worn, do not use it.
Do not overload an electrical outlet.
WARNING
Failure to follow these instructions could result in re, electric shock,
other injuries, or property damage
Failure to follow these instructions could result in re, electric shock,
other injuries, or property damage
(Turn off the power using the power button)
(May cause damage or injury)
(Potential risk of re or unit malfunction)
(Potential risk of re or property damage)
(Potential risk of electric shock or damage)
(Potential risk of malfunction, electric shock,
or re. When the product needs
to be repaired, please contact your reseller)
Dealer
Do not unplug the power cable to turn off
the product.
Do not install the product on an unstable
or inclined surface.
If the product needs to be repaired,
please contact your reseller.
Avoid excessive shock or drops.
Keep product away from the water and
other material.
Do not disassemble, repair or modify the
product.
CAUTION
67
2. Unpacking
SHOULDER
STRAP RING
3. Product Overview
CHARGER
CONNECTOR
COVER OPEN
BUTTON
Front
Bottom
PEELER BODY
PEELER WING
BATTERY
BELT CLIP
CONNECTOR
SERIAL
USB
DISPLAY
Printer Battery Belt Clip
AC cord
Optional
Standard
CD
USB Cable
Quick Reference
Adaptor
Paper
Shoulder Strap
Serial Cable
Battery Cradle
Car Adapter
89
4-1. Display
4. Setting Up the Product
Button
Name
F
unction
Paper Feed /
Down Button
Advances the paper, clears error messages,
and moves down through menu options.
1. Refer to 4-13 for Diagnostic Test information.
2. Refer to the service manual regarding Hexadecimal
Dumping.
Enter Button Selects the highlighted menu option.
Up Button Moves up through menu options.
Power Button
Turns the printer on and off. Press to turn
power on. Press for three seconds to turn power off.
Wakes the printer from sleep mode.
NOTE
1. The battery status LEDs indicate amount of power remaining.
Actual run-time remaining depends on factors such as the contents of output,
distance to computer, etc.
2. When the battery level is very low, high density printing can result in the printer
switching off during printing resulting in possible loss of data.
4-2. Installing the Battery
NOTE
Insert the battery as shown.
You must fully charge the battery when you receive the printer.
Batteries can be charged in the printer or in an optional external cradle.
10 11
4-3. Removing the Battery
Remove the battery as shown.
4-4. Charging the Battery
1. Be sure the printer is turned off.
2. After opening the DC JACK cover, insert DC JACK into the printer.
3. Plug the power cord into the electrical outlet.
4-4-1 The charge indicator LED
Status Charging Charging Completed
Charging Lamp
Red
Green
If there is trouble while charging the battery, the charge indicator LED blinks green.
Try unplugging and reconnecting charger, charging should resume.
Charging is complete when the LED changes to solid green.
NOTE
12 13
4-5-1 The charging status LED
Status charging charging complete
Charging Lamp
Red
Green
NOTE
4-5 Battery charger usage
1. Insert the battery into the battery charger as shown above.
2. Connect the DC JACK to the electrical outlet.
3. Plug the power cord into the electrical outlet.
4. Once the charging is completed, remove the battery from the charger.
Optional
In the case the battery is not inserted properly, the red LED will blink.
Remove and reinsert the battery.
Connect the car charger to the printer.
4-6. Car charger usage
Optional
Input 12V ~ 24V
9.5V / 3A
Output
Connect the car charger to the printer.
NOTE
Lamp
14 15
The belt clip is included with the printer but is not required to be used or installed!
4-7. Belt Clip Usage
Insert screw into belt clip.
Tighten the screw with a screwdriver as shown.
1
2
NOTE
4-8. Interface Cap Installation
1 2
34
When the Interface Cap is disconnected
from the printer, try to orient the Cap Hook
horizontally as shown in the image.
Using a sharp tool, insert the Cap Hook
into the hole located on the right
side of Interface Cap.
When the Cap Hook is inserted, install the
Cap Cover in the direction of the arrow as
shown in the image.
Close the Interface Cap cover.
16 17
NOTE
If the users close the cover with one hand,
it would not be closed completely.
Please use both hands to close.
4-9. Paper Roll Installation
1 2
34
Insert the paper roll so it unrolls from
the bottom. Remove the paper core
when the roll is empty. Pull a short
length of paper out of the printer.
Open the Paper cover by pressing the
Open button. You can set the width of
paper guide by turning the knob with
your nger.
After inserting the paper, adjust the paper
guide so it is slightly wider than paper
size. Then pull the paper out and close the
paper cover.
Close the Paper cover with both hands and
feed some paper by pressing
the Feed button.
Be cautious when handling the product while the Printer Cover is open.
You may have a potential risk of injury when the Paper Cover closes.
CAUTION
Andere Handbücher für LK-P43
3
Inhaltsverzeichnis
Andere SEWOO Drucker Handbücher
SEWOO
SEWOO SLK-TS400 Bedienungsanleitung
SEWOO
SEWOO LK-P20B Bedienungsanleitung
SEWOO
SEWOO SLK-TL12X Series Bedienungsanleitung
SEWOO
SEWOO SLK-TL21 Series Bedienungsanleitung
SEWOO
SEWOO LK-P400 Bedienungsanleitung
SEWOO
SEWOO LK-TL320 Bedienungsanleitung
SEWOO
SEWOO LK-P24 Installationsanleitung
SEWOO
SEWOO SLK-TS400EB Bedienungsanleitung
SEWOO
SEWOO LK-P43 Bedienungsanleitung
SEWOO
SEWOO LK-P12 Bedienungsanleitung
SEWOO
SEWOO SLK-TE122 Bedienungsanleitung
SEWOO
SEWOO SLK-TL20X Series Bedienungsanleitung
SEWOO
SEWOO SLK-T12EB Bedienungsanleitung
SEWOO
SEWOO LK-P25 Bedienungsanleitung
SEWOO
SEWOO LK-P12B Bedienungsanleitung
SEWOO
SEWOO SLK-T21EB Series Bedienungsanleitung
SEWOO
SEWOO LK-P20II Bedienungsanleitung
SEWOO
SEWOO SLK-TE25 Bedienungsanleitung
SEWOO
SEWOO SLK-TL122 Bedienungsanleitung
SEWOO
SEWOO LK-TL200 Bedienungsanleitung
