SEWOO LK-T200 Bedienungsanleitung

All specifications are subject to change without notice

Receipt Printer User’s Manual

MODEL : LK-T200

Rev. 1.0

SEWOO TECH CO.,LTD.

Doosung BD, 689-20, Geumjeong-dong, Gunpo-si, Gyeonggi-do, 435-862, Korea

TEL : +82-31-459-8200 FAX : +82-31-459-8880

www.miniprinter.com

1. Parts Identications 3

2. Setting up the printer 4

2.1 Unpacking 4

2.2 Connecting the cables 5

2.3 Loading the roll paper 9

2.4 Dip switch setting 11

3. Control panel and other functions 14

3.1 Control panel 14

3.2 Error Indicating 14

4. Self Test 15

5. Hexadecimal Dump 16

6. Specications 17

6.1. General Specications 17

6.2. Auto Cutter Specications 19

6.3. Interface 19

6.4. Electrical Characteristics 19

6.5. Environmental Requirements 20

6.6. Reliability 20

6.7. Certication 20

7. Command List 21

Table of Contents 1. Parts Identifications

PRINTER COVER

POWER SWITCH

COVER OPEN LEVER

CONTROL PANEL

Open this cover to

load or replace paper.

Used to turn on/off

power to the printer.

Pull down this lever to

open the printer cover.

Features LED indicators

to indicate printer status

and switches to operate

the printer.

INTERFACE CONNECTOR INTERFACE CONNECTOR(USB)

PERIPHERAL DRIVE CONNECTOR

POWER CONNECTOR

2-2. Connecting the Cables

You can connect up the cables required for printing to the printer.

They all connect to the connector panel on the back of the printer, which is shown below :

Before connecting any of the cables, make sure that both the printer and the computer are turned off.

2-1. Unpacking

Your printer box should include these items. If any items are damaged or missing, please contact your

dealer for assistance.

The Printer User's Manual Roll Paper

Interface Cable(optional) Adaptor(Optional)

2. Setting Up the Printer

For connection to a

host computer.

For connection to a

host computer. For connection of

the AC adapter.

Never unplug the

AC adapter while

the printer is on.

Connects to peripheral units

such as cash drawers, etc.

Do not connect this to

a telephone.

INTERFACE CONNECTOR INTERFACE CONNECTOR(USB)

PERIPHERAL DRIVE CONNECTOR

POWER CONNECTOR

Centronics Parallel Interface

PIN SIGNAL I/O DESCRIPTION

1 STROBE- Input Synchronize signal Data received

2~9 DATA0~7 Input/Output Data bit Transmitted 0~7

10 ACK- Output Data receiving completed.

11 BUSY Output Impossible to print of data receiving.

12 PE Output Paper empty

13 SELECT Output Printer status for ON/OFF line

14 AUTO FEED- Input Paper auto feed signal

15 GROUND - System ground

16 GROUND - System ground

17 NC -

18 LOGIC-H - +3.3V

19~30 GROUND - System ground

31 INIT- Input Initialize

32 ERROR- Output Printer error

33 GROUND - System ground

34 NC -

35 NC -

36 SELLECT IN- Input Printer select signal

Ethernet Interface

PIN SIGNAL I/O

1 Data Out + Output Data +

2 Data Out - Output Data -

3 GND Ground

4 Data IN + Input Data +

5Data IN - Input Data -

6 N.C

7 N.C

8 N.C

2-2-1. Interface Connector

<D-SUB 25 Female Serial> <Centronics Parallel>

USB Interface

PIN SIGNAL I/O DESCRIPTION

1 +5V - +5V

2DATA- - Printer transmit data line

3 DATA+ - Printer transmit data line

4 GND - System Ground

Serial Interface

PIN SIGNAL I/O DESCRIPTION

2 TxD Output Printer transmit data line RS-232C level

3 RxD Input Printer receive data line RS-232C level

4, 20 DTR Output Printer handshake to host line RS-232C level

6 DSR Input Data Send Ready

1, 7 GND - System Ground

2-3. Loading the Roll Paper

Notes: Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the

paper glued to the core because the printer cannot detect the paper end correctly.

(Turn off power switch)

1. Make sure that the printer is not receiving data; Otherwise, data may be lost.

2. Open the paper roll cover by pushing down the cover open button.

3. Remove the used paper roll core if there is one inside.

4. Insert new paper roll as shown.

2-2-2. Cash Drawer Connector

The printer can operate two cash drawers with a 6 pin RJ-11 modular connector.

The driver is capable of supplying a maximum current of 0.1A for 510ms or less when not printing.

PIN SIGNAL DESCRIPTION

1 Signal GND -

2 Drawer kick-out drive signal 1 Output

3 Drawer open/close signal Input

4 +24V -

5 Drawer kick-out drive signal 2 Output

6 Signal GND -

2-4. Dip Switch Setting

The printer is set up at the factory to be appropriate for almost all users. On the other hand,

offers some more settings for users with special requirements.

It has DIP switches that allow you to change communication setting, such as handshaking and parity

check, as well as print density.

Your printer has two sets of DIP switches. The functions of the switches are shown in the following

tables.

♣Note : Power off. And open the cover of Dip Switch and change setting.

2-4-1. Serial Interface Specification

DIP Switch Setting (Standard)

SW FUNCTION ON OFF

2 Hexadecimal HEXDUMP NORMAL

5 Cut Mode Full Cut Partial Cut

6 Handshaking XON/XOFF DTR/DSR

8 Paper Low Mode Paper Low Detect Do not detect

Print Density

Function SW-3 SW-4

Low Power ON ON

Normal OFF ON

Normal ON OFF

Dark OFF OFF

Baud rate selection

Transmission Speed SW-9 SW-10

115200 BPS ON ON

9600 BPS OFF ON

19200 BPS ON OFF

38400BPS OFF OFF

5. Be sure to note the correct direction that the paper comes off the roll.

6. Pull out a small amount of paper, as shown. Then, close the cover.

7. Tear off the paper as shown.

♣CAUTION:

Turn off the printer while removing the DIP switch cover to prevent an electric short, which can

damage the printer.

1. Make sure the printer is turned off.

2. Take off the DIP switch cover as shown in the illustration below.

3. Set the switches using a pointed tool, such as tweezers or a small screwdriver.

4. Replace the DIP switch cover. .

The new settings take effect when you turn on the printer.

♣CAUTION:

When the paper is jammed with cutter, the top cover might be stuck. In this case, repeat power on

and off several times.

If the top cover is still stuck, please follow the steps to release the papers from jamming.

1. Make sure the printer is turned off.

2. Take out DIP switch cover as shown.

3. Turn screw with drivers to a direction until paper is released from the cutter.

3-1. Control panel

You can control the basic paper feeding operations of the printer with the button on the control panel.

The indicator lights help you to monitor the printer’sstatus.

Control Panel

Button

The button can be disabled by the ESC c 5 command.

Press the FEED button once to advance paper one line. You can also hold down the FEED button to

feed paper continuously.

3-2. Error indicators

This section explains the different patterns signaled by the three LED indicators located on the top

cover of the printer.

STATUS PAPER ERROR POWER REMARKS

RED RED GREEN

Power off OFF OFF OFF Normal power is not supplied to

the printer

Power on OFF OFF ON Normal power is supplied to the

printer

On line OFF OFF ON Normal error-free mode

Cover open OFF ON ON Close cover

Paper empty OFF ON ON Insert new paper roll

Paper near end ON OFF ON Paper is low

Test mode OFF OFF ON Ignored error led

3. Control panel and other functions

The self-test lets you know if your printer is operating properly. It checks the control circuits, printer

mechanisms, print quality, ROM version and DIP switch settings.

This test is independent of any other equipment or software.

Running the self test

1. Make sure the printer is turned off and the printer cover is closed properly.

2. While holding down the FEED button, turn on the printer using the switch on the front of

the printer to begin the self-test. The Self Test prints the printer settings and then prints the

following, Cuts the paper, and pauses. (Error LED On)

Self-test printing

Please press the PAPER FEED button.

3. Press the FEED button to continue printing.

The printer prints a pattern using the built-in character set.

4. The self test automatically ends and cuts the paper after printing the following.

*** Completed ***

The printer is ready to receive data as soon as it completes the self-test.

4. Self Test

This feature allows experienced users to see exactly what data is coming to the printer. This can be

useful in finding software problems.

When you turn on the hex dump function, the printer prints all commands and other data in

hexadecimal format along with a guide section to help you find specific commands.

To use the hex dump feature, follow these steps

1. After you make sure that the printer is off and Dip s/w 1-2 is ON, turn on the printer.

2. Run any software program that sends data to the printer. The printer prints “Hexadecimal Dump”

and then all the codes it receives in a two-column format. The first column contains the hexadecimal

codes and the second column gives the ASCⅡ characters that correspond to the codes.

Hexadecimal Dump

1B 21 00 1B 26 02 40 40 .!..& . @ @

1B 25 01 1B 63 34 00 1B .%.. c4 ..

41 42 43 44 45 46 47 48 ABCDEFGH

□A period (.) is printed for each code that has no ASCⅡequivalent.

3. Turn off the printer, and make sure that Dip sw 1-2 off.

4. Turn on the printer.

5. Hexadecimal Dump 6. Specifications

Appendix A : Specifications

6-1. General Specifications

(1) Printing Method Direct line thermal printing.

(2) Print speed 160mm/sec

(3) Dot density

180 DPI (Hor / Ver) 180 / 180 (0.142mm / 0.142mm dot)

203 DPI (Hor / Ver) 203 / 180 (0.125mm / 0.142mm dot)

(4) Printing Width

180 DPI Max 72mm (512 dots)

203 DPI Max 72mm (576 dots)

(5) Number of print columns.

No. of columns

Font “A” Font “B”

180 DPI 42 56

203 DPI 48 64

(6) Roll paper Refer to chapter 2 for details on the recommended roll Paper.

Paper width : 50mm~82.5mm

Roll diameter : Max. Ø80mm

(7) Weight 3.75 lbs (1.7Kg)

Inhaltsverzeichnis

Andere SEWOO Drucker Handbücher

SEWOO

SEWOO LK-P400 Bedienungsanleitung

SEWOO

SEWOO LK-P20II Bedienungsanleitung

SEWOO

SEWOO LK-P11B Bedienungsanleitung

SEWOO

SEWOO LK-P22 Bedienungsanleitung

SEWOO

SEWOO SLK-TL122 Bedienungsanleitung

SEWOO

SEWOO SLK-TL21 Series Bedienungsanleitung

SEWOO

SEWOO LK-P400 Bedienungsanleitung

SEWOO

SEWOO LK-P43B Bedienungsanleitung

SEWOO

SEWOO LK-P31 Bedienungsanleitung

SEWOO

SEWOO LUKHAN LK-P21B Bedienungsanleitung

SEWOO

SEWOO LK-P12W Bedienungsanleitung

SEWOO

SEWOO SLK-TS100 Bedienungsanleitung

SEWOO

SEWOO LK-PXX Bedienungsanleitung

SEWOO

SEWOO WTP-100 Bedienungsanleitung

SEWOO

SEWOO SLK-TL122 Bedienungsanleitung

SEWOO

SEWOO SLK-T32EB Series Bedienungsanleitung

SEWOO

SEWOO LK-P43II Bedienungsanleitung

SEWOO

SEWOO LUKHAN LK-P21B Bedienungsanleitung

SEWOO

SEWOO LK-D10 Bedienungsanleitung

SEWOO

SEWOO LK-P30 Montageanleitung

SEWOO

SEWOO LK-P30 II Bedienungsanleitung

SEWOO

SEWOO STL202II Bedienungsanleitung

SEWOO

SEWOO SLK-T42 Bedienungsanleitung

SEWOO

SEWOO TL32 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung