Sharp UP-600 Bedienungsanleitung
MODEL UP-600
UP-700
CHAPTER 1. REMOVING THE REAR COVER...............................................1
CHAPTER 2. REMOVING THE TOP CABINET...............................................1
CHAPTER 3. REMOVING THE LCD UNIT......................................................2
CHAPTER 4. REMOVING THE PRINTER UNIT .............................................3
CHAPTER 5. REMOVING THE STANDARD DRAWER unit
(For KA, KB version) ..................................................................4
CHAPTER 6. EXPANSION RAM BOARD : UP-S02MB/04MB ........................5
CHAPTER 7. IN-LINE I/F : UP-E10IN..............................................................5
CHAPTER 8. MCR UNIT : UP-E13MR.............................................................6
CHAPTER 9. POLE DISPLAY UNIT : UP-P16DP............................................7
CHAPTER 10. RE-232 I/F : ER-A5RS, EFT & RS-232 I/F : ER-01EF.............7
CHAPTER 11. HAND SCANNER : ER-A6HS1................................................8
CHAPTER 12. REMOTE DRAWER : ER-04DW/05DW...................................9
CHAPTER 13. RS232DEVICES.......................................................................9
CHAPTER 14. ONE HOLE CLERK KIT : DKIT-8669BHZZ (For UP-600) .....10
CHAPTER 15. DRAWER SEPARATION KIT :
DKIT-3409BHZZ (For KA/KB version) ...................................11
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UP-700 UP-600
UP-P16DP
UP-E13MR
In-Line cable
RS232devices
ER-A6HS1
and
RS232devices
>>>>> USE FONT <<<<<
Helvetica/ Helvetica-Condensed/ Century-Schoolbook/ Symbol & OriginalFonts: (RingWorld2/RingFont2/Pa
Symbol/PartsCod)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
CHAPTER 1. REMOVING THE REAR
COVER
1. REMOVING THE REAR COVER
1) Remove the two screws .
2) Remove the rear cover .
2. REPLACING THE REAR COVER
Install the rear cover in the reverse order of removing.
CHAPTER 2. REMOVING THE TOP
CABINET
1. REMOVING THE TOP CABINET
1) Open the printer cover .
2) Lift the pop-up display unit .
3) Remove the three screws .
1
21
1
3
32
3
4) Slightly lift and slide the top cabinet, and remove the grounding
wire .
Note: Do not pull up the top cabinet unit the grounding wire
and connector cables from the top Cabinet are re-
moved.
5) Remove the following cable between the top cabinet and the
main PWB.
Cable between the MAIN PWB and the CKDC PWB.
2. REPLACING THE TOP CABINET
Install the top cabinet in the reverse order of removing.
CHAPTER 3. REMOVING THE LCD
UNIT
1. REMOVING THE LCD UNIT
1) Remove the top cabinet from the bottom cabinet.
2) Remove the LCD flat cable and the earth wire from the
CKDC PWB .
3) Remove the two screws from the LCD HINGE .
4) Remove the LCD unit from the top cabinet.
Insert a flat-bladed screwdriver into the right and left mounting
areas and remove.
4
4
5
3
1
2
4
5
5) With a flat-bladed screwdriver, remove the two latches of each
of the LCD rear cabinet and the LCD filer .
Turn of A and B when you remove it.
2. REPLACING THE LCD UNIT
Install the LCD unit in the reverse order of removing.
CHAPTER 4. REMOVING THE
PRINTER UNIT
1. REMOVING THE PRINTER UNIT
1) Remove the top cabinet.
2) Remove the two screws fixed on the printer unit.
3) Remove the screw fixed on the earth wire .
4) Remove the printer cable from the MAIN PWB (CN9).
2. REPLACING THE PRINTER UNIT
Install the printer unit in the reverse order of removing
6
7
A
B
LCD volum PWB
LCD HS unit
LCD back light
4
11
2
3
CHAPTER 5. REMOVING THE
STANDARD DRAWER
unit (For KA,KB version)
1. REMOVING THE STANDARD DRAWER
UNIT
1) Open the printer cover .
2) Remove the screw fixed on the drawe unit.
3) Stand the main drawer sideways as illusted above, and re-
move the drawer connector from the MAIN PWB (CN:5 ).
2. REPLACING THE STANDARD DRAWER
UNIT
Install the standard drawer unit in the reverse order of removing
The drawer top has the following holes with which the drawer position
can be changed.
A
B
2
2
1
DRCN2
CN4CN5
: Standard position
: Rear position
CHAPTER 6. EXPANSION RAM
BOARD :
UP-S02MB/04MB
1) Open the ROM/RAM case .
2) Install the two spacers on the ROM/RAM PWB unit .
3) Connect the UP-S02MB/04MB to the ROM/RAM PWB unit
(CN:303)
NOTE: The UP-S02MB/S04MB has an electric double layer ca-
pacitor (C21). When removing it after using, use caution
not to bring it close to any conductor.
CHAPTER 7. IN-LINE I/F : UP-E10IN
1) Remove the top cabinet.
2) Install the spacer on the MAIN PWB .
3) Connect the UP-E10IN to the MAIN PWB (CN:304).
4) Fix the UP-E10IN to the spacer with a screw .
5) Pass the TCP/IP cable through the two standard holder
and one core to the following PWB.
UP-E10IN side : CN3, MCR POLE RELAY PWB side :
CN504
7) Remove the rear cover.
8) Connect the LAN cable to the LAN connector .
1
2
3
4
1
2
3
4
5
8
8
9
7
6
9) Install the core to the LAN cable .
NOTE: Install the ferrite core in a position less than 50 mm from
the cabinet.
CHAPTER 8. MCR UNIT : UP-E13MR
1) Align the MCR sheet with the positioning line of the top
cabinet .
2) Mark 3 points of the asterisk mark on the MCR sheet .
3) Aligning with the markings, secure the MCR angle 1 to the
top cabinet with 3 screws .
4) Install the MCR unit to the MCR angle 1 and secure with
2 screws .
5) Remove the rear cover.
6) Connect the MCR cable to the MCR connector .
7) Fix the earth wire to the main chassis with a screw .
8) Install the core to the MCR cable and earth wire with
two wire bands.
10
11
12
IN-LINE cable
Cabinet
Within 50mm
Core
2 2
1
34
4
6
5
7
8
910
11
12
NOTE: Install the ferrite core in a position less than 50 mm from
the cabinet.
CHAPTER 9. POLE DISPLAY UNIT :
UP-P16DP
1) Remove the rear cover.
2) Connect the display cable to the POLE connector .
3) Fix the earth wire to the main chassis with a screw .
4) Install the core to the display cable and earth wire .
Secure the core with two wire bands.
NOTE: Install the ferrite core in a position less than 50 mm from
the cabinet.
CHAPTER 10. RS-232 I/F :ER-A5RS ,
EFT & RS-232 I/F:
ER-01EF
1) Connect the extrnal cables to the I/F board.
<ER-A5RS>
•Install the core (RC0RF6700BHZZ) to the cable with a band.
<ER-01EF>
•Install the core (RC0RF6700BHZZ) to the cable with a band.
NOTE: Install ferrite core in a position less than 10 mm from the
D-sub connector.
Earth wire
Cabinet
MCR cable Wire bandWire band
Core
Within 50mm
2
1
3
5
4
6
Earth wire
Cabinet
MCR cable Wire bandWire band
Core
Within 50mm
Cable
Core
Wire band
D-sub connector
Within 10mm
2) Remove the rear cover.
3) Insert the I/F PWB to the connector of the MAIN PWB
4) Fix the I/F angle to the main chassis with two screws .
CHAPTER 11. HAND SCANNER :
ER-A6HS1
1) Remove the rear cover.
2) Connect the scanner cable to the RS232 CH1 connector.
3) Change the slide switch to the +5V side of the RS232 Relay
PWB unit.
1
24
3
+5V CI
S401
1
Andere Handbücher für UP-600
9
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Sharp Kasse Handbücher
Sharp
Sharp ER-A310 Bedienungsanleitung
Sharp
Sharp XE-A212 Installationsanleitung
Sharp
Sharp XE-A152 Bedienungsanleitung
Sharp
Sharp ER-A320 Bedienungsanleitung
Sharp
Sharp XE-A201 Stücklistenhandbuch
Sharp
Sharp ER-A220 Bedienungsanleitung
Sharp
Sharp UP-600 Bedienungsanleitung
Sharp
Sharp XE-A22S Bedienungsanleitung
Sharp
Sharp XE-A147-BK Bedienungsanleitung
Sharp
Sharp XE-A201 Bedienungsanleitung
Sharp
Sharp ER-A520 Bedienungsanleitung
Sharp
Sharp XE-A407 Bedienungsanleitung
Sharp
Sharp XE-A101 Bedienungsanleitung
Sharp
Sharp ER-3630 Bedienungsanleitung
Sharp
Sharp ER-A250 Bedienungsanleitung
Sharp
Sharp BE-2520 Bedienungsanleitung
Sharp
Sharp UP-3301 Bedienungsanleitung
Sharp
Sharp XE-A207 Bedienungsanleitung
Sharp
Sharp XE-A101 Bedienungsanleitung
Sharp
Sharp XE-A505 - Cash Register, Thermal Printing Bedienungsanleitung
