Sharp XG-SV200X Benutzerhandbuch

MODEL

XG-SV100W

XG-SV200X

DATA PROJECTOR

SETUP MANUAL

Connecting Pin Assignments ............................................................ 2

RS-232C Speciﬁcations and Commands ......................................... 4

Operating the Projector Using the PJLinkTM Protocol .................. 10

Setting up the Projector Network Environment

............................... 11

1. Connecting the Projector to a Computer ............................................ 12

2. Setting an IP Address for the Computer ............................................. 13

3. Setting up a Network Connection for the Projector ............................ 15

Controlling the Projector via LAN ................................................... 17

Controlling the Projector Using Internet Explorer.................................... 17

Conﬁrming the Projector Status (Status)................................................. 18

Controlling the Projector (Control)........................................................... 18

Setting and Adjusting the Projector (Settings & Adjustments)................ 19

Setting the Security (Network – Security)................................................ 19

Making General Settings for the Network (Network – General)............... 20

Setting for Sending E-mail when an Error Occurs

(Mail – Originator Settings) ............................................................ 20

Setting Error Items and Destination Addresses to which E-mail is to be

Sent when an Error Occurs (Mail – Recipient Settings) ................ 21

Setting Error Items and the URL that are to be Displayed

when an Error Occurs (Service & Support – Access URL)............ 21

Resetting the Lamp Timer of the Projector via LAN ..................... 22

Troubleshooting................................................................................ 24

-2

Connecting Pin Assignments

COMPUTER/COMPONENT 1, 2 input and COMPUTER/COMPONENT output Terminals:

mini D-sub 15 pin female connector

COMPUTER Input/Output COMPONENT Input/Output

Pin No. Signal Pin No. Signal

10.

11.

12.

13.

14.

15.

Video input (red)

Video input (green/sync on green)

Video input (blue)

Not connected

Earth (red)

Earth (green/sync on green)

Earth (blue)

Not connected

GND

Not connected

Bi-directional data

Horizontal sync signal: TTL level

Vertical sync signal: TTL level

Data clock

10.

11.

12.

13.

14.

15.

PR (CR)

PB (CB)

Not connected

Earth (PR)

Earth (Y)

Earth (PB)

Not connected

HDMI Terminal

Pin No. Name Pin No. Name

10.

T.M.D.S. Data 2+

T.M.D.S. Data 2 Shield

T.M.D.S. Data 2–

T.M.D.S. Data 1+

T.M.D.S. Data 1 Shield

T.M.D.S. Data 1–

T.M.D.S. Data 0+

T.M.D.S. Data 0 Shield

T.M.D.S. Data 0 –

T.M.D.S. Clock+

11.

12.

13.

14.

15.

16.

17.

18.

19.

T.M.D.S. Clock Shield

T.M.D.S. Clock–

CEC

Utility

SCL

SDA

DDC/CEC ground

+5V power

Hot plug detection

RS-232C Terminal: D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor

Pin No. Signal Name I/O Reference

Receive Data

Send Data

Signal Ground

Request to Send

Clear to Send

Input

Output

Not connected

Connected to internal circuit

Not connected

Connected to internal circuit

Not connected

Connected to CS in internal circuit

Connected to RS in internal circuit

Not connected

218

19 1

218

19 1

-3

RS-232C Cable recommended connection: D-sub 9 pin female connector

Pin No. Signal Pin No. Signal

Projector

Pin No.

Computer

Pin No.

USB Terminal: Type B USB connector LAN Terminal: LAN (RJ-45)

Pin No. Signal Name Pin No. Signal Pin No. Signal

VCC

USB–

USB+

USB power

USB data–

USB data+

Signal Ground

TX+

TX–

RX+

RX–

Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the

controlling device (e.g. computer).

•

Note

Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the

controlling device (e.g. computer).

•

Note

8... 18 ... 1

Connecting Pin Assignments

-4

RS-232C Speciﬁcations and Commands

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control cable (cross

type, commercially available) to the projector. (See page 25 of the projector's operation manual for

connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table.

Signal format: Conforms to RS-232C standard. Parity bit: None

Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit

Data length: 8 bits Flow control: None

*Set the projector's baud rate to the same rate as used by the computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and return code.

After the projector processes the command from the computer, it sends a response code to the

computer.

Command format

C1 C2 C3 C4 P1 P2 P3 P4 Return code (0DH)

Command 4-digit Parameter 4-digit

Response code format

Normal response

Problem response (communication error or incorrect command)

OK Return code (0DH) E R R Return code (0DH)

Info

When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds

after the power has been turned on, and then transmit the commands.

After sending an input selection or picture adjustment command and then receiving an “OK” response

code, the projector may take some time to process the command. If a second command is sent while the

projector is still processing the ﬁrst command, you may receive an “ERR” response code. If this happens,

try resending the second command.

When more than one code is being sent, send each command only after the response code for the

previous command from the projector is veriﬁed.

“POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,

“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”

− When the projector receives the special commands shown above:

* The on-screen display will not disappear.

* The “Auto Power Off” timer will not be reset.

− The special commands are available for applications that require continuous polling.

•

If an underbar (_) appears in the parameter column, enter a space.

If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under

Control Contents.

•

Note

-5

Commands

Example: When turning on the projector, make the following setting.

Computer Projector

POWR___1

CONTROL CONTENTS COMMAND PARAMETER

RETURN

Power ON Standby mode

(or 30-second startup time)

Power On P O W R ___1 OK or ERR OK

Off P O W R ___0 OK OK or ERR

Status POWR????1 0

Projector Condition T A B N ___10:Normal

1: Temp High

8: Lamp Life 5% or less

16: Lamp Burn-out

32: Lamp Ignition Failure

0: Normal

1: Temp High

2: Fan Error

4: Cover Open

8: Lamp Life 5% or less

16: Lamp Burn-out

32: Lamp Ignition Failure

64:

Temp Abnormally High

Lamp Status T L P S ___1 0: Off, 1: On, 2: Retry

3: Waiting, 4: Lamp Error

0: Off, 4: Lamp Error

Power Status T P O W ___1 1: On, 2: Cooling 0: Standby

Quantity T L P N ___11

Usage Time(Hour) T L T T ___1 0 – 9999(Integer)

Usage Time(Minute) T L T M ___1 0, 15, 30, 45

Life(Percentage) TLTL___1 0% – 100%(Integer)

Name Model Name Check T N A M ___1XGSV100W/XGSV200X

Model Name Check M N R D ___1 XG-SV100W/XG-SV200X

Projector Name Setting 1

(First 4 characters) *1

PJN1****OKorERR

Projector Name Setting 2

(Middle 4 characters) *1

PJN2****OKorERR

Projector Name Setting 3

(Last 4 characters) *1

PJN3****OKorERR

Projector Name Check P J N 0 ___1ProjectorName

Input Change COMPUTER1 I R G B ___1 OK or ERR ERR

COMPUTER2 *2 I R G B ___2 OK or ERR ERR

HDMI I R G B ___3 OK or ERR ERR

S-VIDEO I V E D ___1 OK or ERR ERR

VIDEO I V E D ___2 OK or ERR ERR

InputRGBCheck IRGB????

1: COMPUTER1, 2: COMPUTER2,

3: HDMI, ERR

ERR

Input Video Check I V E D ? ? ? ? 1: S-VIDEO, 2: VIDEO or ERR ERR

Input Mode Check I M O D ? ? ? ? 1: RGB, 2: VIDEO ERR

InputCheck ICHK????1:COMPUTER1,

2: COMPUTER2, 3: HDMI,

4: S-VIDEO, 5: VIDEO

ERR

Volume Volume(0 – 60) V O L A __**OKorERR ERR

Volume up/down(-10 – +10) V O U D _***OKorERR ERR

Keystone Vertical -80 – +80 K E Y S _***OKorERR ERR

KEYV_***OKorERR ERR

Horizontal -60 – +60 K E Y H _***OKorERR ERR

AV Mute On I M B K ___1 OK or ERR ERR

Off I M B K ___0 OK or ERR ERR

Freeze On F R E Z ___1 OK or ERR ERR

Off F R E Z ___0 OK or ERR ERR

Auto Sync Start A D J S ___1 OK or ERR ERR

Resize COMPUTER1 Normal R A S R ___1 OK or ERR ERR

16:9 R A S R ___2 OK or ERR ERR

Native R A S R ___3 OK or ERR ERR

Full R A S R ___5 OK or ERR ERR

Border (XG-SV200X only) R A S R ___6 OK or ERR ERR

Area Zoom R A S R __10OKorERR ERR

V-Stretch R A S R __11OKorERR ERR

COMPUTER2 Normal R B S R ___1 OK or ERR ERR

16:9 R B S R ___2 OK or ERR ERR

Native R B S R ___3 OK or ERR ERR

Full R B S R ___5 OK or ERR ERR

Border (XG-SV200X only) R B S R ___6 OK or ERR ERR

Area Zoom R B S R __10OKorERR ERR

V-Stretch R B S R __11OKorERR ERR

RS-232C Speciﬁcations and Commands

-6

CONTROL CONTENTS COMMAND PARAMETER

RETURN

Power ON Standby mode

(or 30-second startup time)

Resize HDMI Normal R C S R ___1 OK or ERR ERR

16:9 R C S R ___2 OK or ERR ERR

Native R C S R ___3 OK or ERR ERR

Full R C S R ___5 OK or ERR ERR

Border (XG-SV200X only) R C S R ___6 OK or ERR ERR

Area Zoom R C S R __10OKorERR ERR

V-Stretch R C S R __11OKorERR ERR

S-VIDEO Normal R A S V ___1 OK or ERR ERR

16:9 R A S V ___2 OK or ERR ERR

Border (XG-SV200X only) R A S V ___3 OK or ERR ERR

Area Zoom R A S V __10OKorERR ERR

V-Stretch R A S V __11OKorERR ERR

VIDEO Normal R B S V ___1 OK or ERR ERR

16:9 R B S V ___2 OK or ERR ERR

Border (XG-SV200X only) R B S V ___3 OK or ERR ERR

Area Zoom R B S V __10OKorERR ERR

V-Stretch R B S V __11OKorERR ERR

ALL Reset ALRE___1 OK or ERR ERR

COMPUTER1 INPUT Picture Mode Standard R A P S __10OKorERR ERR

Presentation RAPS__11OKorERR ERR

Movie RAPS__12OKorERR ERR

Game RAPS__13OKorERR ERR

sRGB RAPS__14OKorERR ERR

Contrast -30 – +30 R A P I _* * * OK or ERR ERR

Bright -30 – +30 R A B R _* * * OK or ERR ERR

Red -30 – +30 R A R D _* * * OK or ERR ERR

Blue -30 – +30 R A B E _* * * OK or ERR ERR

Color -30 – +30 R A C O _* * * OK or ERR ERR

Tint -30 – +30 R A T I _* * * OK or ERR ERR

Sharp -30 – +30 R A S H _* * * OK or ERR ERR

CLR Temp -2 – +2 R A C T __**OKorERR ERR

BrilliantColor™

0 – +2 R A W E ___* OK or ERR ERR

DNR Off R A N R ___0 OK or ERR ERR

Level 1 R A N R ___1 OK or ERR ERR

Level 2 R A N R ___2 OK or ERR ERR

Level 3 R A N R ___3 OK or ERR ERR

Picture Reset R A R E ___1 OK or ERR ERR

SignalType Auto IASI___0 OK or ERR ERR

RGB I A S I ___1 OK or ERR ERR

YPbPr I A S I ___2 OK or ERR ERR

Audio Input Audio 1 R A A I ___1 OK or ERR ERR

Audio 2 R A A I ___2 OK or ERR ERR

COMPUTER2 INPUT Picture Mode Standard R B P S __10OKorERR ERR

Presentation R B P S __11OKorERR ERR

Movie R B P S __12OKorERR ERR

Game R B P S __13OKorERR ERR

sRGB R B P S __14OKorERR ERR

Contrast -30 – +30 R B P I _* * * OK or ERR ERR

Bright -30–+30 RBBR_* * * OK or ERR ERR

Red -30 – +30 R B R D _* * * OK or ERR ERR

Blue -30 – +30 R B B E _* * * OK or ERR ERR

Color -30 – +30 R B C O _* * * OK or ERR ERR

Tint -30 – +30 R B T I _* * * OK or ERR ERR

Sharp -30 – +30 R B S H _* * * OK or ERR ERR

CLR Temp -2 – +2 R B C T __**OKorERR ERR

BrilliantColor™

0 – +2 R B W E ___* OK or ERR ERR

DNR Off R B N R ___0 OK or ERR ERR

Level 1 R B N R ___1 OK or ERR ERR

Level 2 R B N R ___2 OK or ERR ERR

Level 3 R B N R ___3 OK or ERR ERR

PictureReset RBRE ___1 OK or ERR ERR

Signal Type Auto I B S I ___0 OK or ERR ERR

RGB I B S I ___1 OK or ERR ERR

YPbPr I B S I ___2 OK or ERR ERR

Audio Input Audio 1 R B A I ___1 OK or ERR ERR

Audio 2 R B A I ___2 OK or ERR ERR

RS-232C Speciﬁcations and Commands

-7

CONTROL CONTENTS COMMAND PARAMETER

RETURN

Power ON Standby mode

(or 30-second startup time)

HDMI INPUT Picture Mode Standard R C P S __10OKorERR ERR

Presentation R C P S __11OKorERR ERR

Movie R C P S __12OKorERR ERR

Game R C P S __13OKorERR ERR

sRGB R C P S __14OKorERR ERR

Contrast -30 – +30 R C P I _***OKorERR ERR

Bright -30 – +30 R C B R _***OKorERR ERR

Red -30 – +30 R C R D _***OKorERR ERR

Blue -30 – +30 R C B E _***OKorERR ERR

Color -30 – +30 R C C O _***OKorERR ERR

Tint -30 – +30 R C T I _***OKorERR ERR

Sharp -30 – +30 R C S H _***OKorERR ERR

CLR Temp -2 – +2 R C C T __**OKorERR ERR

BrilliantColor™

0 – +2 R C W E ___* OK or ERR ERR

DNR Off R C N R ___0 OK or ERR ERR

Level 1 R C N R ___1 OK or ERR ERR

Level 2 R C N R ___2 OK or ERR ERR

Level 3 R C N R ___3 OK or ERR ERR

Picture Reset R C R E ___1 OK or ERR ERR

Signal Type Auto I C S I ___0 OK or ERR ERR

RGB I C S I ___1 OK or ERR ERR

YPbPr I C S I ___2 OK or ERR ERR

Audio Input Audio 1 R C A I ___1 OK or ERR ERR

Audio 2 R C A I ___2 OK or ERR ERR

HDMI R C A I ___3 OK or ERR ERR

Dynamic

Range

Auto H M C D ___0 OK or ERR ERR

Standard H M C D ___1 OK or ERR ERR

Enhanced H M C D ___2 OK or ERR ERR

S-VIDEO INPUT Picture Mode Standard V A P S __10OKorERR ERR

Presentation VAPS__11OKorERR ERR

Movie VAPS__12OKorERR ERR

Game VAPS__13OKorERR ERR

Contrast -30 – +30 V A P I _***OKorERR ERR

Bright -30 – +30 V A B R _***OKorERR ERR

Red -30 – +30 V A R D _***OKorERR ERR

Blue -30 – +30 V A B E _***OKorERR ERR

Color -30 – +30 V A C O _***OKorERR ERR

Tint -30 – +30 V A T I _***OKorERR ERR

Sharp -30 – +30 V A S H _***OKorERR ERR

CLR Temp -2 – +2 V A C T __**OKorERR ERR

BrilliantColor™

0 – +2 V A W E ___* OK or ERR ERR

DNR Off V A N R ___0 OK or ERR ERR

Level 1 V A N R ___1 OK or ERR ERR

Level 2 V A N R ___2 OK or ERR ERR

Level 3 V A N R ___3 OK or ERR ERR

Picture Reset V A R E ___1 OK or ERR ERR

Audio Input Audio 1 V A A I ___1 OK or ERR ERR

Audio 2 V A A I ___2 OK or ERR ERR

VIDEO INPUT Picture Mode Standard V B P S __10OKorERR ERR

Presentation V B P S __11OKorERR ERR

Movie V B P S __12OKorERR ERR

Game V B P S __13OKorERR ERR

Contrast -30 – +30 V B P I _***OKorERR ERR

Bright -30 – +30 V B B R _***OKorERR ERR

Red -30 – +30 V B R D _***OKorERR ERR

Blue -30 – +30 V B B E _***OKorERR ERR

Color -30 – +30 V B C O _***OKorERR ERR

Tint -30 – +30 V B T I _***OKorERR ERR

Sharp -30 – +30 V B S H _***OKorERR ERR

CLR Temp -2 – +2 V B C T __**OKorERR ERR

BrilliantColor™

0 – +2 V B W E ___* OK or ERR ERR

DNR Off V B N R ___0 OK or ERR ERR

Level 1 V B N R ___1 OK or ERR ERR

Level 2 V B N R ___2 OK or ERR ERR

Level 3 V B N R ___3 OK or ERR ERR

Picture Reset V B R E ___1 OK or ERR ERR

Audio Input Audio 1 V B A I ___1 OK or ERR ERR

Audio 2 V B A I ___2 OK or ERR ERR

RS-232C Speciﬁcations and Commands

-8

CONTROL CONTENTS COMMAND PARAMETER

RETURN

Power ON Standby mode

(or 30-second startup time)

Clock -150 – +150 I N C L * * * * OK or ERR ERR

Phase -30 – +30 I N P H _* * * OK or ERR ERR

H-position -150–+150 IAHP****OKorERR ERR

V-position -60 – +60 I A V P _* * * OK or ERR ERR

Fine Sync Adjustment Reset I A R E ___1 OK or ERR ERR

Overscan On O V S N ___1 OK or ERR ERR

Off O V S N ___0 OK or ERR ERR

OSD Display On I M D I ___1 OK or ERR ERR

Off I M D I ___0 OK or ERR ERR

Video System Auto M E S Y ___1 OK or ERR ERR

PAL M E S Y ___2 OK or ERR ERR

SECAM M E S Y ___3 OK or ERR ERR

NTSC4.43 M E S Y ___4 OK or ERR ERR

NTSC3.58 M E S Y ___5 OK or ERR ERR

PAL-M M E S Y ___6 OK or ERR ERR

PAL-N M E S Y ___7 OK or ERR ERR

PAL-60 M E S Y ___8 OK or ERR ERR

Background Logo I M B G ___1 OK or ERR ERR

Blue I M B G ___3 OK or ERR ERR

None I M B G ___4 OK or ERR ERR

Eco+Quiet On T H M D ___1 OK or ERR ERR

Off T H M D ___0 OK or ERR ERR

Auto Sync On A A D J ___1 OK or ERR ERR

Off A A D J ___0 OK or ERR ERR

Auto Power Off On A P O W ___1 OK or ERR ERR

Off A P O W ___0 OK or ERR ERR

Auto Restart On A R E S ___1 OK or ERR ERR

Off A R E S ___0 OK or ERR ERR

STANDBY Mode Standard M O U T ___1 OK or ERR ERR

Eco M O U T ___0 OK or ERR ERR

PRJ Mode Reverse On I M R E ___1 OK or ERR ERR

Off I M R E ___0 OK or ERR ERR

Invert On I M I N ___1 OK or ERR ERR

Off I M I N ___0 OK or ERR ERR

Language English M E L A ___1 OK or ERR ERR

Deutsch M E L A ___2 OK or ERR ERR

Español M E L A ___3 OK or ERR ERR

Nederlands M E L A ___4 OK or ERR ERR

Français M E L A ___5 OK or ERR ERR

Italiano M E L A ___6 OK or ERR ERR

Svenska M E L A ___7 OK or ERR ERR

ME L A ___8 OK or ERR ERR

Português M E L A ___9 OK or ERR ERR

ME L A __10OKorERR ERR

ME L A __11OKorERR ERR

ME L A __12OKorERR ERR

ME L A __13OKorERR ERR

polski M E L A __14OKorERR ERR

Türkçe M E L A __15OKorERR ERR

ME L A __16OKorERR ERR

Magyar M E L A __17OKorERR ERR

TiӃng ViӋtME L A __18

OK or ERR ERR

Audio Out FAO A O U T ___1 OK or ERR ERR

VAO A O U T ___2 OK or ERR ERR

InternalSpeaker On ASPK___1 OK or ERR ERR

Off ASPK___0 OK or ERR ERR

RGB Frequency Check Horizontal T F R Q ___1 kHz(***.* or ERR) ERR

Vertical T F R Q ___2 Hz(***.* or ERR) ERR

Fan Mode Normal H L M D ___0 OK or ERR ERR

High H L M D ___1 OK or ERR ERR

Treble -30 − +30 A A T E _***OKorERR ERR

Bass -30 − +30 A A B A _***OKorERR ERR

WallColor Off WLCO _ _ _ 0OKorERR ERR

Blackboard WLCO _ _ _ 1OKorERR ERR

Whiteboard WLCO_ _ _ 2OKorERR ERR

COMPUTER2 Select *3 Input R B S E _ _ _ 0 OK or ERR ERR

Monitor Output R B S E _ _ _ 1 OK or ERR ERR

DLP®LinkTM Off 3 D E N _ _ _ 0 OK or ERR ERR

On 3 D E N _ _ _ 1 OK or ERR ERR

DLP®LinkTM Invert 3 D I V _ _ _ 1 OK or ERR ERR

RS-232C Speciﬁcations and Commands

-9

CONTROL CONTENTS COMMAND PARAMETER

RETURN

Power ON Standby mode

(or 30-second startup time)

Video Setup 0 IRE V I S U _ _ _ 0 OK or ERR ERR

7.5 IRE V I S U _ _ _ 1 OK or ERR ERR

Closed Caption

(For Americas only)

Off C L C A _ _ _ 0 OK or ERR ERR

CC1 C L C A _ _ _ 1 OK or ERR ERR

CC2 C L C A _ _ _ 2 OK or ERR ERR

LENS Focus(-255-+255) LNFO****OKorERR ERR

Zoom(-255-+255) LNZO****OKorERR ERR

VerticalLensShift(-800-+800)*6 LNSH****OKorERR ERR

LNUD****OKorERR ERR

HorizontalLensShift(-800-+800)*6 LNLR****OKorERR ERR

Lens Shift Center *6 L N P D _ _ _ 1 OK or ERR ERR

ROTATE*4 -800−+800 SVLR****OKorERR ERR

Rotate Indicator *4 On S V B L ___1 OK or ERR ERR

Off S V B L ___0 OK or ERR ERR

MEMORY Save(1-8) LNSV****OKorERR ERR

Load(1-8)*6 LNLO****OKorERR ERR

Clear(1-8) LNCR****OKorERR ERR

Mute On LNMM___1OKorERR ERR

Off LNMM___0OKorERR ERR

Lock On LNML___1OKorERR ERR

Off LNML___0OKorERR ERR

Reset Network Setting L N R E _ _ _ 1 OK or ERR OK or ERR

Restart Network L R E S _ _ _ 1 OK or ERR OK or ERR

LampTimerReset*5 LPRE0001ERR OKorERR

*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.

*2 When “COMPUTER2 Select” is set to “Monitor Output”, you may receive an “ERR” response code.

*3 When “COMPUTER2” is selected in the INPUT list, “COMPUTER2 Select” cannot be set to “Monitor

Output”.

*4 This command can send only when the ceiling-mount rotating module (AN-SV100T: commercially available)

is connected to the projector.

*5 The Lamp Timer Reset command is available only in standby mode.

*6 If the lens cover is not correctly attached, you may receive an “ERR” response code.

RS-232C Speciﬁcations and Commands

-10

Operating the Projector Using the PJLinkTM Protocol

The projector conforms with the PJLinkTM standard Class 1.

The commands to be used in controlling the projector by the PJLinkTM protocol are as

shown below.

CONTROL CONTENTS COMMAND RETURN

Power Control Off P O W R _ 0 OK or ERR3

On P O W R _ 1 OK or ERR3

Power Status Query P O W R _ ? 0: Standby Mode

1: Power On

2: Standby (Cooling)

3: Power On (Warming up)

Input List Query I N S T _ ? 11 12 21 22 31

Input Change COMPUTER1 I N P T _ 1 1 OK or ERR3

COMPUTER2 I N P T _ 1 2 OK or ERR3

HDMI I N P T _ 3 1 OK or ERR3

S-VIDEO I N P T _ 2 1 OK or ERR3

VIDEO I N P T _ 2 2 OK or ERR3

Input Status Query I N P T _ ? 11: COMPUTER1

12: COMPUTER2

31: HDMI

21: S-VIDEO

22: VIDEO

or ERR3

AV Mute Off A V M T _ 3 0 OK or ERR3

On A V M T _ 3 1 OK or ERR3

AV Mute Status Query A V M T _ ? 30: Off

31: On

or ERR3

Lamp Query L A M P _ ? 1st Number: Lamp Usage Time (Hour)

2nd Number: 0: Lamp Off 1: Lamp on

Error Condition Query E R S T _ ? 1st Byte: Fan Error Status

2nd Byte: Lamp Error Status

3rd Byte: Temp. Error Status

4th Byte: Cover Open Status

5th Byte: Not Used, Return 0

6th Byte: Other Error Status

0: No Error Detected

1: Warning

2: Error Detected

Projector Name Query * N A M E _ ? Projector Name

Manufacture Name Query I N F 1 _ ? SHARP

Pruduct Name Query I N F 2 _ ? XG-SV100W/XG-SV200X

Other Information Query I N F O _ ? Not used

Class Information Query C L S S _ ? 1

* You can set “Projector Name” at “Making General Setting for the Network (Network-General)” on page 20.

PJLinkTM Authentication:

The password to be used for PJLinkTM is the same as the one you have set in “Setting the Security (Network-

Security)” (page 19). When operating without authentication, do not set a password.

PJLinkTM Compliant:

This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.

This product conﬁrms with the PJLink standard speciﬁcation version 1.00.

For additional information, visit “http://pjlink.jbmia.or.jp/english/”.

Andere Handbücher für XG-SV200X

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sharp Projektor Handbücher

Sharp

Sharp XV-Z3100U Bedienungsanleitung

Sharp

Sharp Notevision PG-A10S Bedienungsanleitung

Sharp

Sharp Notevision XG-C40XU Bedienungsanleitung

Sharp

Sharp XR40X - XGA DLP Projector Bedienungsanleitung

Sharp

Sharp PG-M20XU Bedienungsanleitung

Sharp

Sharp XG-F315X Bedienungsanleitung

Sharp

Sharp XV-Z90E Bedienungsanleitung

Sharp

Sharp XV-Z3100U Bedienungsanleitung

Sharp

Sharp Notevision XG-C435X-L Bedienungsanleitung

Sharp

Sharp XG-P25X - Conference Series XGA LCD... Bedienungsanleitung

Sharp

Sharp PG-D210U Bedienungsanleitung

Sharp

Sharp XV-Z30000 Operation Bedienungsanleitung

Sharp

Sharp PG-D2500X Bedienungsanleitung

Sharp

Sharp PG-D120U - Pro - LCD Projector Bedienungsanleitung

Sharp

Sharp PG-LX3000 Handbuch

Sharp

Sharp XG-PH50X - XGA DLP Projector Bedienungsanleitung

Sharp

Sharp EL-99T Bedienungsanleitung

Sharp

Sharp Notevision XG-NV7XU Bedienungsanleitung

Sharp

Sharp XV-Z200U/E Bedienungsanleitung

Sharp

Sharp Notevision PG-MB60X Bedienungsanleitung

Sharp

Sharp PG-D3750W - WXGA DLP Projector 720p Bedienungsanleitung

Sharp

Sharp DT-500 Bedienungsanleitung

Sharp

Sharp NoteVision PG-LS2000 Bedienungsanleitung

Sharp

Sharp Notevision XR-20XA Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung