Safety Precautions *Please observe the following precautions
• The danger & its extent if the product is handled improperly. • The meaning of the graphic symbol used in the text.
Purpose of use
• This product is to reduces the contact of liquid droplets and dust to the face. Do not use it as a protective device against solids or fire.
Care
• If the film surface become dirty, soak a soft cloth such as tissue or eyeglass cloth with commercially available rubbing
alcohol (excluding gel type) or diluted neutral detergent, and wipe it gently. If uneveness remains after wiping, wipe it gently
with a tissue soaked in water and wrung well. There is concave and convex processing on the film. If you rub it violently,
the uneveness is broken and the function may deteriorate.
Name of each part Instruction on use
Precautions for use
• It cannot be used in places where harmful dust or gas is generated, or for the purpose of preventing them.
• Discontinue use if you have an abnormality on your skin or it does not fit your skin.
• If you feel sick while wearing it, discontinue to use.
• If you feel that your head is tight, adjust the mounting position or insert some material like cushion.
• Please keep out of reach of infants.
• Do not use or stone near fire.
• Store this product away from high temperatures and humidity and places exposed to deirect sunlight.
• When disposing of this product, please dispose of it in accordance with the regulations of the local government.
Warning May cause death or serious injury
Caution Risk of minor injury or property damage
Indicates that you must not do
Indicates that you should do
Warning To prevent injury
Frame
Film
Caution To prevent injury
• If it is damaged, never use it.
• Do not clean with benzene, thinner, kerosene,
acidic detergent, alkaline detergent, etc.
• Do not use in situations where there is a high risk
of this product will fall off.
• Never disassemble or modify the main body or accessories.
• Do not use it only by children or within reach of infants.
• Do not use for purposes other than those described in this manual.
• Do not use while driving a car / motorcycle or bicycle.
• Be careful when handling the film in a way that the edges
of the film do not hurt your hands or face.
• Not use if the film is damaged or dirty.
• Install the film and frame correctly according to the instructions
in this manual.
• Discontinue use if you have an abnormality on your skin
or if it does not fit your skin.
Projection
Projection
SHARP Logo
Hook
Claw
Claw
Hook
Hole Hole Hole Hole
Projecting
Mark
1 2
43
Projecting
Mark
Two holes are provided so that the angle of
the film when the face shield is attached can
be changed in two steps. It becomes shallow
to insert the claws of the frame into the upper
hole, and it becomes deep to insert the claws
of the frame into the pilot holes
Shallow Deep
Film takeout RemovingFitting
Film angle switching hole
Upper: Shallow
Lower: Deep
You can prevent fingerprints from adhering to
the film by taking out only thetop of the film
with holes and attaching the film to the frame.
2.Remove the holes on the
film side in the order
from the claws on the frame.
2 1
1. Remove the two holes
in the center of the film from
the protrusions on the frame.
34
Preparation
• Set the projecting mark on the film towards SHARP logo side on the frame.
Procedure
1. Insert the claws of the frame in the order of holes holes
on the film side.
2. Fit the priorusions of the frame into the two holes and
in the center of the film.
Wearing
• Lightly spread the handle of the frame and attach it to your head.
• Secure the frame on your forehead.
• If it loose, pass a commercially available elastic cord through the
hook of the frame and tighten it.
34
1 2
1
2
4
3
SHARP
Logo
Projecting
Mark
SHARP ELECTRONICS (MALAYSIA) SDN. BHD. (356997-H)
No.1A, Persiaran Kuala Langat, Section 27, 40400 Shah Alam, Selangor Darul Ehsan, Malaysia.
