Shimano MTB SHADOW RD Series Bedienungsanleitung

(English)

DM-RD0001-05

Dealer's Manual

MTB Rear Derailleur

MTB SHADOW RD+

RD-M986

RD-M820

RD-M786

RD-M675

RD-M640

New

RD-M615

MTB SHADOW RD

RD-M981

RD-M781

RD-M670

New

RD-M610

RD-M4000

RD-M3000

CONTENTS

IMPORTANT NOTICE.............................................................................................. 3

TO ENSURE SAFETY............................................................................................... 4

INSTALLATION ....................................................................................................... 6

Direct mount .......................................................................................................................6

Replacing with direct mount type .....................................................................................7

Mode converter (RD-M820)................................................................................................8

ADJUSTMENT ........................................................................................................ 9

How to use the end adjust bolt (SHADOW RD+) ..............................................................9

SIS Adjustment (SHADOW RD+).......................................................................................11

MAINTENANCE.................................................................................................... 12

Replacing the bump stopper/holder (RD-M820).............................................................12

Replacing the plate and the plate tension spring (RD-M986)........................................14

Replacing the plate and the plate tension spring (except RD-M986)............................17

Replacing the B tension spring (RD-M4000 / RD-M3000) ...............................................20

Friction adjustment (RD-M986)........................................................................................21

Friction adjustment (except RD-M986)............................................................................23

Applying grease to the chain stabilizer...........................................................................25

Replacing the pulley .........................................................................................................26

IMPORTANT NOTICE

•

This dealer’s manual is intended primarily for use by professional bicycle mechanics.

Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the

dealer’s manuals.

If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place

of purchase or a local bicycle dealer for their assistance.

•

Make sure to read all instruction manuals included with the product.

•

Do not disassemble or modify the product other than as stated in the information contained in this dealer’s manual.

•

All dealer’s manuals and instruction manuals can be viewed on-line on our website (http://si.shimano.com).

•

Please observe the appropriate rules and regulations of the country, state or region in which you conduct your business as a

dealer.

For safety, be sure to read this dealer's manual thoroughly before use, and follow it for correct use.

The following instructions must be observed at all times in order to prevent personal injury and physical damage to

equipment and surroundings.

The instructions are classified according to the degree of danger or damage which may occur if the product is used

incorrectly.

DANGER

Failure to follow the instructions will result in death or serious injury.

WARNING

Failure to follow the instructions could result in death or serious injury.

CAUTION

Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.

TO ENSURE SAFETY

WARNING

•

When installing components, be sure to follow the instructions that are given in the instruction manuals.

It is recommended that you use only genuine Shimano parts. If parts such as bolts and nuts become loose or damaged, the bicycle

may suddenly fall over, which may cause serious injury.

In addition, if adjustments are not carried out correctly, problems may occur, and the bicycle may suddenly fall over, which may

cause serious injury.

•

Be sure to wear safety glasses or goggles to protect your eyes while performing maintenance tasks such as replacing parts.

•

After reading the dealer’s manual thoroughly, keep it in a safe place for later reference.

Be sure to also inform users of the following:

•

Maintenance interval depends on the usage and riding circumstances. Clean regularly the chain with an

appropriate chain cleaner. Never use alkali based or acid based solvents such as rust cleaners. If those solvent be

used chain might break and cause serious injury.

•

Check the chain for any damage (deformation or crack), skipping, or other abnormalities such as unintended gear shifting. If

any problems are found, consult a dealer or an agency. The chain may break, and you may fall.

CAUTION

For Installation to the Bicycle, and Maintenance:

•

When installing and removing the plate and the plate unit, be careful to avoid injury such as getting your fingers caught by

the strong reaction force of the plate tension spring.

NOTE

Be sure to also inform users of the following:

•

When installing the SHADOW RD+, be sure to install the plate unit cover before riding the bicycle.

•

If gear shifting operations cannot be carried out smoothly, clean the derailleur and lubricate all moving parts.

•

If the amount of looseness in the links is so great that adjustment is not possible, you should replace the derailleur.

•

Products are not guaranteed against natural wear and deterioration from normal use and aging.

•

For maximum performance we highly recommend Shimano lubricants and maintenance products.

For Installation to the Bicycle, and Maintenance:

•

Depending on the shape of the frame, the rear derailleur may interfere with the chain stay.

•

Because the high cable resistance of a frame with internal cable routing would impair the SIS function, this type of frame

should not be used.

•

Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly.

•

Do not let dust adhere on the inner cable. If the grease on the inner cable is wiped off, the application of SIS SP41 grease

(Y04180000) is recommended. Do not use DURA-ACE grease or other types of grease, otherwise they may cause deterioration

in gear shifting performance.

•

For smooth operation, use the specified outer casing and the bottom bracket cable guide.

•

Use an outer casing which still has some length to spare even when the handlebars are turned all the way to both sides.

Furthermore, check that the shifting lever does not touch the bicycle frame when the handlebars are turned all the way.

•

If gear shifting adjustment cannot be carried out, check the degree of parallelism at the rear end of the bicycle. Also check if

the cable is lubricated and if the outer casing is too long or too short.

•

You should periodically clean the derailleur and lubricate all moving parts (mechanism and pulleys).

•

Depending on the model, the guide pulley has arrows on it to indicate the direction of rotation. Install the guide pulley so that

the arrows are pointing counterclockwise when looking at the outer side of the derailleur.

•

The tension pulley has an arrow on it to indicate the direction of rotation. Install the tension pulley so that the arrow is

pointing clockwise when looking at the outer side of the derailleur.

•

If you hear abnormal noise as a result of looseness in a pulley, you should replace the pulley.

The actual product may differ from the illustration because this manual is intended chiefly to explain the procedures for using

the product.

INSTALLATION

List of tools to be used

The following tools are needed to assemble this product.

Where to use Tool

Bracket axle 5 mm Allen key

Mode converter 2 mm Allen key (RD-M820)

End adjust bolt Screwdriver #2

3 mm Allen key (RD-M820)

Bump stopper 3 mm Allen key

1.5 mm Allen key

Plate stopper pin Screwdriver #2

Plate unit cover bolt 2 mm Allen key

Plate axle 4 mm Allen key

Guide pulley/Tension pulley 3 mm Allen key

Top/Low adjustment screw Screwdriver #2

Move the lever switch to the OFF position before installing the SHADOW RD+.

Lever switch

OFF

Refer to "REAR DERAILLEUR FOR MTB/TREKKING" in the General Operations for installation to the frame.



Direct mount

Note:

Direct mount rear derailleurs can only be mounted on direct-mount compatible frames.

The E-ring is not

necessary for installation.

5 mm Allen key

Tightening torque:

8.0 - 10.0 N·m {70 - 87 in. lbs.}



Replacing with direct mount type

If there is an E-ring attached, use a flat-head screwdriver to remove it.

Using a 5 mm Allen key, remove the bracket axle.

•

If there is a spacer, remove it.

•

The E-ring is not necessary for installation.

E-ring 5 mm Allen key

Bracket

Spacer

Tightening torque:

8.0 - 10.0 N·m {70 - 87 in. lbs.}

When replacing the direct mount type with the bracket-equipped type, reverse the procedure.

•

For models with a spacer, insert the spacer into the correct position.



Mode converter (RD-M820)

This derailleur is compatible with two types of sprockets: Freeride mode (11-32T/11-34T/11-36T) and downhill mode (11-23T/12-

25T/11-28T).

If using the freeride mode sprockets, you will also need to use the mode converter.

Removing the mode converter

Mode converter

2 mm Allen key

Tightening torque:

1.0 - 1.5 N·m {9 - 13 in. lbs.}

When a mode converter is installed

When a mode converter is not installed

Bracket

Dropout

ADJUSTMENT

This section describes the adjustment procedure for the SHADOW RD+.

Refer to ”Rear derailleur” in the General Operations for items not explained in this section.



How to use the end adjust bolt (SHADOW RD+)

Note:

Move the lever switch to the OFF position to reduce the tension of the plate tension spring before carrying out this

adjustment.

If the lever switch remains at the ON position so that the screw is difficult to turn, the screw may become damaged if you try to

force it to turn.

Set the rear derailleur to the low gear.

After stopping the wheel, check that the distance between the tip of the guide pulley and the tip of the gear is within the

range shown in the illustration.

Largest sprocket

5 - 6mm

•

Screwdriver #2

End adjust bolt

Turn the crank to shift gears to check that other gears do not have a rough feel.

Checking the distance between the sprocket and the guide pulley (RD-M820/M640)

Note:

If the number of teeth for the cassette sprocket is changed, carry out this setting again.

Set the rear derailleur to the largest (at freeride mode) or the smallest (at downhill mode) gear position.

Stop the wheel from turning, and then check that the distance from the edge of the guide pulley to the edge of the

sprocket is within the range as shown in the illustration.

•

Screwdriver #2

•

3 mm Allen key for

RD-M820 only

End adjust bolt

Freeride mode

Largest sprocket Smallest sprocket

5 - 6mm

Downhill mode

10 - 11mm

If the frame interferes with the rear derailleur on models with a bump stopper when the plate unit is lifted up, turn the end

adjust bolt until there is no interference.

Load:

approx. 49 - 78.4 N

The frame and the rear derailleur should not interfere.

Turn the crank arm to shift gears and check that there is no roughness in the feel.

Note: RD-M640 About freeride specification/downhill specification

RD-M640 differs between freeride specification and downhill specification.

The specification cannot be changed by replacing the bracket only.

A mode converter is not equipped, either.

Downhill specification

Freeride specification

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Shimano Fahrradzubehör Handbücher

Shimano

Shimano BR-M545 Betriebsanleitung

Shimano

Shimano FC-T8000 Bedienungsanleitung

Shimano

Shimano Ultegra ST-6870 Bedienungsanleitung

Shimano

Shimano ALFINE Inter-11 Bedienungsanleitung

Shimano

Shimano FC-R9100-P Bedienungsanleitung

Shimano

Shimano RD-M410 Betriebsanleitung

Shimano

Shimano SL-BS79 Betriebsanleitung

Shimano

Shimano Steps SC-E6100 Bedienungsanleitung

Shimano

Shimano XTR Betriebsanleitung

Shimano

Shimano RD-7800 Bedienungsanleitung

Shimano

Shimano RD-M810 Betriebsanleitung

Shimano

Shimano FD-M665 Betriebsanleitung

Shimano

Shimano SG-3C41 Bedienungsanleitung

Shimano

Shimano DI2 Adapter B Bedienungsanleitung

Shimano

Shimano RD-TX35 Betriebsanleitung

Shimano

Shimano TIAGRA FD-4400 - TECHNICAL Betriebsanleitung

Shimano

Shimano HP-NX10 Betriebsanleitung

Shimano

Shimano NEXUS SG-7C26 Betriebsanleitung

Shimano

Shimano DH-3D71 Betriebsanleitung

Shimano

Shimano DURA-ACE ST-7970 Bedienungsanleitung

Shimano

Shimano XTR FC-M980 Betriebsanleitung

Shimano

Shimano FD-M985-E Bedienungsanleitung

Shimano

Shimano SI-TIREB Betriebsanleitung

Shimano

Shimano SC-MT800 Bedienungsanleitung

Beliebte Fahrradzubehör Handbücher anderer Marken

Sigma

Sigma BC 16.16 Bedienungsanleitung

Playcore

Playcore Dero Setbacks Bedienungsanleitung

VDO Cyclecomputing

VDO Cyclecomputing x3dw Bedienungsanleitung

Cateye

Cateye RAPID X2 Bedienungsanleitung

buratti meccanica

buratti meccanica Clorofilla Trail Bedienungsanleitung

BOB

BOB YAK Bedienungsanleitung

APLIC

APLIC 303303/20190717TW012 Bedienungsanleitung

SRAM

SRAM AXS BlipBox Bedienungsanleitung

Garmin

Garmin EDGE 500 Bedienungsanleitung

Cateye

Cateye V2C - Gebrauchsanweisung

KMART

KMART 43115907 Bedienungsanleitung

SIGMA SPORT

SIGMA SPORT Buster 2000 Bedienungsanleitung

NVO Components

NVO Components STEM Bedienungsanleitung

DAXYS

DAXYS BP188 Bedienungsanleitung

XLC

XLC BV-W17 Bedienungsanleitung

Deda Elementi

Deda Elementi SUPERBOX Bedienungsanleitung

Akku Vision

Akku Vision e-bike vision 10046 Kurzanleitung

Squire

Squire Inigma Bedienungsanleitung