Shinybow USA SB-6355 Bedienungsanleitung

SB-6355 KIT

HDMI HDBaseT™ 4K/UHD Tx & Rx Extender KIT up to 330 Feet (100M)

(PoH, Dual LAN, 2-way IR, RS-232, SPDIF, Analog Audio, HDMI)

INSTRUCTION MANUAL

RECEIVER

TRANSMITTER

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.

Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and

excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience

receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the

means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC

voltage is not covered by any warranty.

10. Turn power off and disconnect unit from AC current before making connections.

11. Never hold a power switch in the “ON” position.

12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use

the unit near stoves, heat registers, radiators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal

ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky

environment, the unit should be periodically “blown free” of foreign dust and matter.

14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to

qualied service personnel. There are no user serviceable parts inside.

15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to

other devices.

16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,

use only the original factory packing.

19. Service Information Equipment should be serviced by qualier service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain

D. The equipment does not appear to operate normally, or exhibits a marked change in performance

E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

CONTENTS

INTRODUCTION ..............................................................1

FEATURES&CONTENTS................................................2

SPECIFICATIONS ........................................................... 3

TRANSMITTER PANELS ................................................ 4

RECEIVER PANELS ....................................................... 6

IR PIN CONFIGURATION ............................................... 8

RS-232 PIN CONFIGURATION ...................................... 10

TYPICAL HDBaseT™ APPLICATION ........................... 12

RACK MOUNTS (OPTIONAL) ....................................... 13

WALL MOUNT APPLICATIONS .................................... 15

INTRODUCTION

Congratulations on your purchase of one of the most innovative

HDMI 1.4a over single category cable HDBaseT™ Transmitter/

Receiver with POH (Power Over HDBaseT™) on the market

today. SB-6355T HDBaseT™ Transmitter can transmit the HDMI,

Ethernet, PoE with power (48VDC), IR Remote signals input to

Receiver or output to destination and the RS-232 interface signal

I/O to HDBaseT™ Receiver SB-6355R via single LAN (category)

cable for the long distance Maximum 328 feet (100M). Transmitter

use the single UTP/FTP (category cable) CAT6, CAT6a or CAT7

via RJ-45 8P8C female socket (Support 568a/b). This product

provide higher full HD HDMI 1.4a, Resolution supports 480i/p,

720p,1080i/p or High full 4K2K-30Hz/24bpp, 4K2K-60Hz/24bpp

with 4:2:0 pixel fromet quality that are identical to the source high

quality full HDMI 1.4 signals. The Transmitter is useful for sending

the 4K2K HDMI digital Video / multi-channel digital audio format,

IR remote in or out, Ethernet, RS-232 in-out, KVM (USB2.0) and

48VDC power over HDBaseT™ (PoH) to HDBaseT™ Receiver.

Controls signals via Single category cable transmit to the

HDBaseT™ Transmitter and HDBaseT™ Receiver.

HDBaseT™ with PoH 100M EXTENDER Series

Thank you for purchasing the SB-6355x Kit HDBaseT™ with PoH Transmitter and Receiver. You will nd this unit easy to

install and highly reliable but it is essential that you read this manual thoroughly before attempting to use the converter.

TABLE OF CONTENTS

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the

PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. We assume no responsibility for any

infringements of patents or other rights of third parties which may

result from its use.

We assume no responsibility for any inaccuracies that may be

contained in this document. We make no commitment to update

or to keep current the information contained in this document.

We reserve the right to make improvements to this document

and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means

— electronic, mechanical, magnetic, optical, chemical, manual,

or otherwise — without express written permission and consent

Version 2.0 JUNE 2015

6355TR-20150623-002

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may

be trademarks of the companies with which they are associated.

FEATURES

• HDBaseT™ HDMI / DVI extender over CATX (UTP/STP) cable

• Compatible with HDMI 2.0 and HDCP 1.x, 2.2 complient

• Supports 5play feature set over a single LAN cable. Transmits HDMI, Digital Audio, Bi-directional IR(CIR), 100Base-Tx Ethernet,

USB 2.0, RS-232 I/O, SPDIF I/O and 13W PoH

• Application NxK AV matrixes, AV receivers, HD projectors, Single wire Tvs and Two-box Tvx, KVM (Keyboard, Video, Mouse)

extension, digital signage display

• HDMI 1080p@60 video V1.4a 3D and Ultra HD 4K2K video, CEC / HDCP compliant

• Supports link speeds of up to Video, TMDS format Max. 10.2 Gbit/s, Signal 340MHz Deep Color, Full HD 1080p@60Hz@24/36/48bit/pixels

• Supports 1080p TV’s at 24/30/60/100/200/240 Hz and above as well as Blu-rays at 24 FPS

• Supports Digital Audio 7.1 LPCM 192KHz, 24bits, Full HD Dolby TrueHD and DTS-HD Master

• Audio uncompressed HD audio formats

• Transfer Bi-directional Infrared control signal together with the HDMI signal

• Supports HDMI CEC between your connected Source and display gear

• With LED indicators to show the POWER/POE/LINK/HDCP status

• Support external Bi-Directional SPDIF in/out and available for multichannel audio

• Support stereo audio I/O with PCM 2CH

• Support Super Audio CD (DSD), CEC commands protocol table

• Extend long distance 4K2K 340MHz/328 feet(100 Meters) or 1080p 148.5MHz/429 feet(150 M)

• Surface Mounting bracket included, Other mounting brackets available as a separate option

• Power Input Tx & Rx 48VDC(12.48W), Rx 12VDC(4.8W) with Low power consumes (4K load 500mA)

• Power supply using universal power switch 50/60Hz,100~240VAC

PACKAGE CONTENTS

Check that you have the following components;

• SB-6355x HDBaseT™ Extender console

• SB-100 set (IR Receiver Extender assy plug)

• SB-100C cable (IR Receiver Cable)

• SB-101 set (IR Transmitter Extender assy plug)

• SB-101C cable (IR Transmitter Cable)

• 1 inch High Wall mount pack (Part # WM-1INCH-L210MM)

• Users Guide

• AC Adaptor :

• Transmitter: 48VDC/1A (universal power switch 50/60Hz,100~240VAC)

• Receiver: 12VDC/1A (universal power switch 50/60Hz,100~240VAC)

Optional Accessories :

• CAT6 Category cable distance 328 feet (100Meter), (P/N: UTP6-100)

FEATURES & CONTENTS

SPECIFICATIONS

• Type of Extender: HDBaseT™ 5play set over a single LAN category UTP/STP Cable

• Transmit Signals: HD Video/Audio, 100Base-TX Ethernet, USB (KVM), SPDIF input, SPDIF output, RS-232 i/o, IR input, IR output

and PoE (48VDC)

• HDMl Supports: HDMI 1.4 and HDMI 2.0

• HDCP Supports: HDCP 1.X, 2.2 compliant

• Video Support: Ultra HD (4K2K@30Hz) with YCbCr 4:4:4 and 4K2K@60Hz YCbCr 4:2:0, format up to 1080p@60Hz@48b/pixel

and deep color, 3D

• Video Bandwidth: 10.2 Gbps (340MHz)

• Audio I/O Supports: Multi Audio Formats 5.1/7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital, DTS, DTS-HD Master,

(PCM-2CH)

• Extra S/PDIF I/O: External Bi-Directional SPDIF in/out, Dolby Digital, DTS, Dolby TrueHD, DTS HD-Master Audio, Dolby Pro Logic

Iiz 7.1 & 9.1, and more.

• Ethernet Support: 100bps BaseTx

• KVM Support: USB 2.0

• IR Infrared Frequency: 38Khz

• Power Over HDBaseT™: 48VDC (100W power using PoH)

• Category Cable Support: CAT6, CAT6a, CAT7 UTP/STP cable

• Scan Rate Accepted: Supports HDMI full HD Resolution; Frequency 24Hz to 240Hz

• Controls: 1x IR in, 1x IR out, 1x RS-232 I/O, 1x USB (Host), 2x USB (Device) and 2x LAN series interface

• Transfer Distance: Up to 10.2Ghz/297Mhz, 328 feet(100 meters)/4K2K / Up to 4GHz/148.5Mhz, 492 feet(150 Meters)/1080p

• HDMI I/O Connectors: HDMI Type A-SMD 19pin Female Type

• HDBaseT™ I/O Connectors: HDBaseT™ RJ-45, 8p8c Female socket

• PoE Support: Transmitter (48VDC) to Receiver

• Temperature: Operating Temperature 32°F - 100°F (0°C - 38°C)

• Chassis Material/Color: Metal (think 1mm) / Black

• Dimensions (LxWxH): 8.26 x 4.45 x 1.06 in (210x113x 27 mm)

• Rack Mount (19 inch): #1U high 19 inch install 1x Unit. / #5U high 19 inch install Total 10 pcs Rack mountable

• Shipping Weight (net): Transmitter: 0.70 kgs/1.54 lb - Receiver: 0.58 kgs/1.27 lb

• Safety Approvals: CE, FCC, VCCI & REACH

• Power Consumption:

•Transmitter: 4K Full load

•w/ PoE: Max 300mA (48VDC, 12.48W)

•w/o PoE: Max 400mA (12VDC, 4.8W)

•Receiver: 4K Full load

•w/o PoE: Extra power Max 500mA (12VDC, 6.0W)

• Transmitter Power Supply: Power Input +48VDC, 1A (Universal Type 50/60Hz, 100~240 VAC)

• Receiver Power Supply: Extra Power Input +12VDC, 1A (Universal Type 50/60Hz, 100~240 VAC) (Using Exra power when

HDBaseT™ Transmitter w/o support PoE)

As product improvements are continuous, specications are subject to change and without notice.

SPECIFICATIONS

TRANSMITTER FRONT PANEL

FRONT PANEL

1. POWER ON SWITCH: The power switch turns the unit on and off. The LED will illuminate blue to indicate that the switcher is ON and

is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last

conguration will be evoked.

2. PoE LED DISPLAY: Power over HDBaseT™ boot on and off status via LED show out.

3. LINK LED DISPLAY: HDBaseT™ link status via LED illuminates blue to indicate that a HDBaseT™ is present on that input.

4. HDCP LED DISPLAY: HDCP status via LED show out.

5. FIRMWARE UPDATE: Firmware Update connection this OD3.5mm jack port.

6.DISTANCE SELECT SWITCH: Select Extend distance for 100 meters / 4K2K or 150 meters / 1080p.

7. USB HOST: Setup the USB port is HOST.

8. USB DEVICE: Setup the USB port is DEVICE.

9. SELECT HOST OR DEVICE SWITCH: Switch Select the USB is HOST or DEVICE.

TRANSMITTER BACK PANEL

BACK PANEL

1. POWER INPUT: DC48V, 1A, (Din-4pins Male Plug).

2. RS-232 I/O: Send RS-232 via HDBaseT™ CATx cable.

3. SPDIF OUTPUT: Receive the SPDIF signal from HDBaseT™

Receiver via HDBaseT™ CATx cable.

4. SPDIF INPUT: Send the SPDIF signal to HDBaseT™ Receiver via

HDBaseT™ CATx cable.

5. HDBaseT™ OUTPUT (Transmitter): HDBaseT™ send HDMI

Source signal to Receiver via HDBaseT™ RJ-45

connector.

6. HDMI INPUT: HDMI signal Input.

7/8. AUDIO INPUT: Extra Stereo Audio signal Input.

9/10. LAN I/O: LAN controls I/O.

11. IR OUTPUT: Receive Bi-directional IR signal from HDBaseT™

Receiver to Control source device.

12. IR INPUT: Send Bi-directional IR signal to HDBaseT™ Receiver

to Control destination device.

RECEIVER FRONT PANEL

FRONT PANEL

1. POWER LED DISPLAY: The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and

is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last

conguration will be evoked.

2. PoE LED DISPLAY: Power over HDBaseT™ boot on and off status via LED show out.

3. LINK LED DISPLAY: HDBaseT™ link status via LED illuminates blue to indicate that a HDBaseT™ is present on that input.

4. HDCP LED DISPLAY: HDCP status via LED show out.

5. FIRMWARE UPDATE: Firmware Update connection this OD3.5mm jack port.

6. DISTANCE SELECT SWITCH: Select Extend distance for 100M / 4K2K or 150M / 1080p.

7. USB HOST: Setup the USB port is HOST.

8. USB DEVICE: Setup the USB port is DEVICE.

9. SELECT HOST OR DEVICE SWITCH: Switch Select the USB is HOST or DEVICE.

RECEIVER BACK PANEL

BACK PANEL

1. POWER INPUT (Extra): DC12V, 1A, (Male Plug). Extra power offer

when Transmitter PoE absent.

2. RS-232 I/O: Send RS-232 via HDBaseT™ CATx cable.

3. SPDIF INPUT: Send the SPDIF signal to HDBaseT™ Receiver via

HDBaseT™ CATx cable.

4. SPDIF OUTPUT: Receive the SPDIF signal from HDBaseT™

Receiver via HDBaseT™ CATx cable.

5. HDBaseT™ INPUT: ( From Transmitter) HDBaseT™ sends HDMI

Source signal from Transmitter via HDBT RJ-45

connector.

6. HDMI OUTPUT: HDMI signal Output to destination.

7. AUDIO OUTPUT: Extra Stereo Audio signal output.

8./9. LAN I/O: LAN controls I/O.

11. IR INPUT: Send Bi-directional IR signal to HDBaseT™

Transmitter to Control destination device.

12. IR OUTPUT: Receive Bi-directional IR signal from HDBaseT™

Receiver to Control source device.

IR PIN CONFIGURATION - TRANSMITTER

REAR PANEL IR EXTENDER PORT - TRANSMITTER

Note: When you plug the External IR extender into the switcher, the front panel IR receiver remains active.

IR EXTENDER PACKAGE

HOW TO SETUP THE IR EXTENDER RECEIVER COMPONENTS

Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka:

stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.

Inhaltsverzeichnis

Andere Shinybow USA Sender Handbücher

Shinybow USA

Shinybow USA SB-6335T4 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung