Shure SCM410 Bedienungsanleitung
1/25
SCM410 SCM410E -- Four-Channel Micro-
phone Mixer
Safety Information
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accor-
dance with the manufacturer’s instructions.
8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other appara-
tus (including amplifiers) that produce heat. Do not place any open flame sources on the product.
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-
aged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vas-
es, on the apparatus.
16. The MAINS plug or an appliance coupler shall remain readily operable.
Shure Incorporated
2/25
17. The airborne noise of the Apparatus does not exceed 70dB (A).
18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing
connection.
19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
21. Operate this product within its specified operating temperature range.
Shure Incorporated
3/25
This symbol indicates that dangerous voltage constituting a risk
of electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this unit.
WARNING: Voltages in this equipment are hazardous to life. No user-ser-
viceable parts inside. Refer all servicing to qualified service personnel. The
safety certifications do not apply when the operating voltage is changed
from the factory setting.
General Description
The Shure Model SCM410/E is a four-channel automatic microphone mix-
er for use in sound reinforcement, audio recording, and broadcast applica-
tions. The SCM410 dramatically improves audio quality in any application
where multiple microphones are required. Any low-impedance dynamic or
condenser microphone (including wireless) can be used with the SCM410.
Multiple SCM410 mixers can be linked to other SCM410 mixers, as well as
to Shure Models FP410, SCM810, and SCM800.
Each input channel has a two-band equalizer and three logic terminals.
The equalizer reduces unwanted low-frequency audio pickup and makes
different microphone types-lavaliers, boundary and handheldsound similar.
The logic terminals can be used to control external devices.
The SCM410 operates on 100-120 Vac power and the SCM410E operates
on 220-240 Vac power. Each mixer is supplied with a power cord, rack-
mounting hardware, and a link cable.
Features
•Fast, noise-free microphone selection, which automatically adjusts to changes in background noise
• Automatic gain adjustment as additional microphones are activated- NOMA (Number of Open Microphones At-
tenuated)
•Last Mic Lock-On circuit maintains ambient sound
•Fits in half-rack space
•Adjustable EQ for each channel
•Active balanced microphone-level XLR inputs and an active balanced Mic/Line level XLR output
•Unbalanced auxiliary-level phono output
Shure Incorporated
4/25
•Bi-color channel activation and clipping LEDs
•Peak-responding output limiter with LED indicator
•Peak-responding output level meter
Operating Principles
The operating concept behind the SCM410 Automatic Mixer is Shure's proprietary IntelliMix® circuitry. Intellimix
delivers seamless automatic mixing by combining three separate functions:
•Noise Adaptive Threshold. Distinguishes between constant background noise (such as air conditioning) and
changing sound (such as speech) for each input channel. It continuously adjusts the activation threshold so that
only speech levels louder than the background noise activate a channel.
•MaxBus. Controls the number of channels that may be activated for a single sound source. One talker activates
only one channel, even if multiple microphones “hear” that talker.
•Last Mic Lock-On. Keeps the most recently activated microphone open until another microphone is activated.
Without Last Mic Lock-On, a long pause in conversation would cause all microphones to turn off, which would
sound as if the audio signal had been lost. Last Mic Lock-On ensures that background ambience is always
present.
IntelliMix is a registered trademark of Shure Incorporated.
Front Panel
Microphone Channel Gain Controls 1 - 4
Allows adjustment of microphone gain.
Input LED 1 - 4
Lights green when channel is active; lights red at 6 dB below clipping level.
Low-Cut Filter 1 - 4
Provides adjustable low-frequency rolloff (high pass), reducing presence of undesirable low-frequency signals.
High-Frequency Shelving Filter 1 - 4
Provides level boost or cut in mid/high-frequency region for reduced sibilance from vocal microphones, or to com-
pensate for off-axis coloration in lavalier microphones.
Output Level Meter
Six-segment LED meter indicates peak output signal level in dBu (0 dBu = 0.775V). The red LED illuminates when
the output is 6 dB below clipping. The last LED indicates limiter action.
MASTER Level Control
1
2
3
4
5
6
Shure Incorporated
5/25
Controls overall output level.
POWER LED
Lights green when mixer is plugged into a power source.
POWER Switch
Turns the mixer on and off.
Note: Country dependant
Rear Panel
Power Connector
Unit is energized when the power cord is plugged into a 100-120 Vac (SCM410) or 220-240 Vac (SCM410E) pow-
er source. NOTE: There is no power On/Off switch on this mixer.
DIP Switch
The 4-position DIP switch provides additional functions. Refer to the “DIP Switch Functions”section.
Microphone Logic Connector
High density DB-15 male connector provides connection to GATE OUT, MUTE IN, and OVERRIDE IN logic termi-
nals on each channel. Refer to the “Advanced Functions” section.
Note: This is not a VGA monitor port.
AUX OUT Phono Connector
Feeds consumer-level audio equipment, such as a tape recorder, VCR, or video camera. Not affected by MIC/
LINE switch.
MIC/LINE XLR OUTPUT Connector
Can be set for microphone or line-level output via a DIP switch.
LINK IN/OUT Connector
Permits multiple SCM410/E, FP410, SCM810, SCM800, or AMS8100 mixers to be linked, creating additional in-
puts.
MIC LEVEL XLR INPUT Connectors
Active balanced microphone-level XLR inputs. For instructions on how to modify the level of these inputs, refer to
the “Internal Modifications” Addendum.
7
8
1
2
3
4
5
6
7
Shure Incorporated
6/25
DIP Switch Functions
The rear panel DIP switches, shown in Figure 1, provide the functions listed in the table below.
Last Mic Lock-On XLR Output Level Limiter 12V Phantom Pow-
er
Switch Number 1 2 3 4
Switch Up All mics off after
hold time
Mic Level ON ON
Switch Down ON* Line Level OFF* OFF*
* Factory setting
Last Mic Lock-On
Keeps the most recently activated microphone turned on until another microphone is activated. When defeated,
microphones turn off after their default hold time. XLR Output Level: Sets the level of the XLR output to line or mi-
crophone level. Make sure the output level matches the input level of the device connected to the SCM410.
Note: The output level does not affect the auxiliary output (AUX OUT) level.
Limiter
Activates the output limiter and sets it to a default threshold of +16 dBu (see Internal Modifications Addendum for
other threshold settings).
12V Phantom Power
When this switch is in the ON position, the SCM410 provides 12Vdc phantom power to each XLR microphone in-
put. This function is particularly useful when using condenser microphones, since most condenser microphones
require phantom power.
Note: Phantom power does not affect the operation of balanced dynamic microphones. They can be connected to
the SCM410 in combination with condenser microphones that use phantom power. For instructions on how to dis-
able phantom power by channel, refer to the Internal Modifications Addendum.
Installation
Rack Mounting
The SCM410 is supplied with hardware for mounting one or two units to a 19-inch audio equipment rack. The
hardware can also be used to rack mount other Shure products, including the SCM268, SCM262, DFR11EQ, and
the DP11EQ.
Shure Incorporated
7/25
Single Mixer (Half Rack) Installation
1. Attach the short and long rack-mount brackets to the SCM410/E with eight (8) of the supplied bracket screws.
INSTALLING HALF RACK MOUNTING BRACKETS
2. Place the mixer in an equipment rack and secure it with the supplied rack-mount screws and plastic washers.
RACK MOUNTING A SINGLE SCM410/E MIXER
Dual Mixer (Full Rack) Installation
1. Place the two mixers side-by-side and connect them with two (2) straddle brackets. The brackets should strad-
dle the recessed edges on the top and bottom of each mixer.
INSTALLING STRADDLE BRACKETS
2. Fasten the straddle brackets using eight (8) bracket screws.
3. Attach the short rack-mount brackets to the outsides of the combined mixers with eight (8) of the bracket
screws.
INSTALLING FULL RACK MOUNTING BRACKETS
4. Place the mixer in an equipment rack, using the supplied rack-mount screws and plastic washers.
Shure Incorporated
8/25
RACK MOUNTING DUAL SCM410/E MIXERS
Table-Top Mounting
Adhere the four (4) supplied rubber feet to the bottom of the mixer at each corner. This will keep it from sliding and
protect the table surface.
ATTACHING RUBBER FEET FOR TABLE-TOP MOUNTING
Fixed Mounting
Top Mount
1. Fasten the straddle brackets to the recessed edges of the chassis, using four (4) bracket screws.
INSTALLING STRADDLE BRACKETS FOR TOP MOUNTING
2. Fasten the straddle brackets to the top of the mounting surface, using the four (4) supplied wood screws.
Shure Incorporated
9/25
SECURING MIXER TO TOP MOUNTING SURFACE
Hanging Mount
Note: The hardware provided is for attachment to wood. Other surfaces require the use of appropriate hardware
rated for 15 lbs. or more.
1. Fasten the straddle brackets to the top of the mixer.
INSTALLING STRADDLE BRACKETS FOR HANG MOUNTING
2. Fasten the straddle brackets to the bottom of the mounting surface, using the four (4) supplied wood screws.
SECURING MIXER TO BOTTOM MOUNTING SURFACE
SCM410 Connections
1. Connect microphone signal sources to the Channel Input connectors. Use conventional 2-conductor shielded
audio cables.
2. If any condenser microphones are connected, set the +12V phantom power DIP switch to ON.
3. Connect the SCM410 Mic/Line Level Output to the input of mixers, EQs, amplifiers, or recorders.
4. Connect the power cord to 100-120 Vac (SCM410) or 220-240 Vac (SCM410E)
Shure Incorporated
10/25
Linking Multiple Mixers
If more than four inputs are needed, multiple Shure SCM410, FP410, or SCM810 mixers can be linked by connect-
ing the LINK OUT of the first mixer to the LINK IN of the next mixer, and so on. See Figure 2. Leave the LINK IN
jack of the first mixer and the LINK OUT jack of the last mixer unconnected.
When properly linked, the mixers will operate as a system. Automatic mixing functions will be shared by all units.
All input signals appear at all linked mixer outputs. Each mixer's Master level control only controls its own output.
However, actual off-attenuation will increase as more mixers are linked. This reduces excessive noise and rever-
beration contributed by the increased number of microphones.
Important: When using logic terminals on linked mixers, connect the LOGIC GROUND terminals of each
unit together.
Note: SCM410 link connections are unbalanced. To minimize hum and noise, avoid using longer link cables. Use
high quality, shielded cable, and keep them away from sources of magnetic or electrical noise, such as power
transformers or light dimmers. To minimize ground currents, make sure linked mixers are connected to the same
AC power mains.
FIGURE 1: LINKED SCM410 AND SCM810 MIXERS
Andere Handbücher für SCM410
3
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Shure Mikrofon Handbücher
Shure
Shure KSM44A Bedienungsanleitung
Shure
Shure 16A Bedienungsanleitung
Shure
Shure M44G Bedienungsanleitung
Shure
Shure Microflex Advance MXA910 Bedienungsanleitung
Shure
Shure SM27 Bedienungsanleitung
Shure
Shure KSM8 Dualdyne Bedienungsanleitung
Shure
Shure VP88 Bedienungsanleitung
Shure
Shure KSM44 Bedienungsanleitung
Shure
Shure W10BT Bedienungsanleitung
Shure
Shure 527A Bedienungsanleitung
Shure
Shure PG42-USB Bedienungsanleitung
Shure
Shure Microflex MX391 Series Bedienungsanleitung
Shure
Shure VP83F Bedienungsanleitung
Shure
Shure 522 Bedienungsanleitung
Shure
Shure MX153 Bedienungsanleitung
Shure
Shure SM81 Bedienungsanleitung
Shure
Shure 550L Bedienungsanleitung
Shure
Shure ROSWELLITE KSM313 Kurzanleitung
Shure
Shure 710A Series Bedienungsanleitung
Shure
Shure Beta 98HC Bedienungsanleitung
Beliebte Mikrofon Handbücher anderer Marken
IK Multimedia
IK Multimedia iRig Stream MIC PRO Bedienungsanleitung
DAPAudio
DAPAudio RM-101 Bedienungsanleitung
AKG
AKG CHM 21 Bedienungsanleitung
Sennheiser
Sennheiser evolution wireless series EM 100 Bedienungsanleitung
Sony
Sony C-48 Bedienungsanleitung
GIGAMEDIA
GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung
