Shure Unisphere I PE56D-CN Bedienungsanleitung

MODEL PE56D-CN

UNISPHEREB

Slips out

swivel stand

adapter, easily and quickly.

for hand-held use.

Your selection of a Shure

UNISPHERE~

Cardioid Micro-

phone will contribute significantly to the professional

quality of your performance. This ball-type microphone

has a wire-mesh screen with a special filter which provides

protection from wind, blast and "pop" (explosive breath

sounds). This feature allows you to work as close to the

microphone as you wish, either indoors or out-of-doors.

Another feature of your unidirectional microphone is

that it effectively controls feedback (that very annoying

loudspeaker "squeal") because it picks up sound only from

the front of the microphone. Unwanted audience noise or

other noises occurring at the rear of the microphone are

eliminated or suppressed. This allows you to work at sig-

nificantly greater distances from your microphone than

with non-directional (omnidirectional) microphones, with-

out picking up objectionable background sound or feedback.

(See inside for information on how to use your

Shcire Microphone more effectively

HOW TO CONTROL FEEDBACK

performer's number one enemy in using a microphone is

"feedback." This is a harsh hum, howl or squeal which oc-

curs when the microphone picks up sound from the

loudspeakers, re-amplifies and rebroadcasts it over and

over again.

The key factor in the prevention of feedback is the posi-

tion of the loudspeakers in relation to the microphone.

Feedback occurs if the microphone picks up sound coming

from the loudspeakers. Keep the loudspeakers as far to the

sides as possible-so they do not point toward the micro-

phone. Always keep the microphone pointed toward the

performer and away from the loudspeakers. When stage

monitor loudspeakers are used, make sure they are posi-

tioned in front of the performers and face the rear of the

microphone.

If you are in a room with hard walls, floor, and ceiling,

the sound from the loudspeakers may bounce back into the

microphone and create feedback. Solve this problem by

turning down the amplitier volume control and working

closer to the microphone.

(Important Note: If you cannot solve the feedback prob-

lem with your

UNISPHERE@

microphone, a Shure

Feedback Controller is suggested.)

BASIC POINTS FOR PROFESSIONAL

MICROPHONE TECHNIQUE

Proper microphone technique will add to the overall ef-

fectiveness with which you project yourself to your

audience. Keep the following points in mind when using

the microphone:

Maintain the proper distance from the microphone.

When you wish to achieve an intimate tonal quality,

get closer to the microphone and lower your voice. For

wide-open "driving" effects, raise your voice and back

away from the microphone so that you do not over-

drive your amplifier to distortion.

Don't change your distance from the microphone

needlessly, as this will affect the level of sound coming

from the loudspeakers.

Consider the microphone as an instrument and prac-

tice your technique to enhance your performance.

YOUR SHURE MICROPHONE IS BUILT TO LAST!

Your Shure Microphone is ruggedly built and should give

you years of uninterrupted service; however, remember

that it is a sensitive instrument. Avoid dropping the micro-

phone, or subjecting it to unnecessarily rough treatment.

Normal usage, of course, will not impair performance of

the unit. Use the protective carrying case to prevent dam-

age not only when traveling, but also when storing the

microphone.

MICROPHONE CHECK-LIST

Check microphone impedance-is it correct for the

amplifier input being used?

Check microphone cable connectors to microphone,

mixer and amplifier-are they tightly plugged in?

Check microphone, amplifier and/or mixer.

a. Are they turned on?

b. Are volume controls turned up?

IF THE MICROPHONE DOES NOT WORK

Check the above list. If the microphone still does not

appear to be operating, check it on a spare cable. If the

microphone still does not appear to be operating, have the

microphone and cable checked by your Shure Professional

Entertainer Products Dealer, or write Service Department,

Shure Brothers. Inc.

PHASING

To test two microphones and/or their.cables for proper

phasing, connect them to an amplifier and talk or sing into

them while holding them three or four inches apart. The

sound from the speakers should be the same when talking

into either microphone or directly between them if they

are in phase with each other. If the sound drops drastically,

or if a dead spot is found when talking between the two

microphones, one of them or its cable (low impedance

only) is out of phase. All cables and microphones should

be tested in this manner to insure that they are in phase

with each other.

To change the phase of a low-impedance microphone

cable, either use a Shure AlSPR Phase Reverser or inter-

change the wires connected to pins

and

of the connec-

tor. To change the phase of a microphone, the microphone

cartridge leads must be interchanged (see Figure 2). This

should be performed by your dealer, the Shure Factory

Service Department, or other qualified service personnel.

IMPEDANCE

Your microphone as supplied is wired for low impedance

for connection to low-impedance microphone inputs (rated

to 300 ohms). To change microphone wiring for

connection to high-impedance microphone inputs, remove

male plug insert by turning slotted setscrew inward (coun-

terclockwise). Disconnect the two-terminal impedance

selection socket from the rear of the male insert, and

reconnect the socket in reverse position so that pin

the male insert is inserted in socket terminal

"H".

NOTE: After following the above directions, the PE56D-

CN with the supplied two-conductor CSICN cable will

be suitable for connection directly to high-impedance

inputs using three-pin professional audio connectors. For

direct connection to

in. phone jack inputs, replace the

CSlCN cable with the C5-X: 6.lm (20 ft) single-con-

ductor shielded with three-pinprofessional audio connector

(female) on microphone end and

in. phone plug on

equipment end.

USING MORE THAN ONE MICROPHONE

It is often desirable for a group to use a separate micro-

phone for each individual performer. In this case, the

following points should be remembered:

It is best if the microphones are individually controlled

for volume through a separate Shure microphone

mixer.

If this is not possible, it is desirable that each

performer use the same type and model of tnicrophone

so that the group

a whole will be "balanced."

Check the placement of the microphones with relation

to loudspeakers (as previously mentioned) so that

feedback is minimized.

As additional microphones are added the possibility of

feedback increases. Turn off, or down, unused micro-

phones to help solve this problem.

SHURE FEEDBACK CONTROLLER

Lets you "tune" your sound system to the acoustics of the

room. The result is more overall sound power

without

feedback. Eight linear-motion filter controls are infinitely

variable from

dB cut. Below

and Above

kHz roll-off switches attenuate low and high frequencies.

Can be installed between mixer or console and amplifier

for total system control, or following each microphone as

a single-channel preamplifier with feedback control.

THE

VlCTAL

LINK

BEmm

YOU

AND

AITDLENCE

SHURE PROFESSIONAL ENTERTAINER

hAICRnPHONFS

ODEL

PE56D-CN SPECIFICATIONS

YP~:

Dynamic, Cardioid (Unidirectional)

Frequency

Response:

to :5,000 Hz (see Figure

Impedance:

Output Level

(at

1,000

Hz):

Phasing:

,*EM*.

"SRT2

FIGURE

Dual Low Mtcrophore ratlng impedance is 150 ohms

(28

Hlgh Microphone impedance is

"High

for connectlon t

hlgh-impedance microphone Inputs

Wlred for low impedance as supplled (see Page

MPEDANCE

Low High

Open Circuit Voltage*

.-77.0

-54.5

(.I41

mV)

(1.89

mV)

Power Level*

. .

.-57.5

volt per microbar

**O

milliwatt with

microbar;

Low Impedance: Positive pressure on diaphragm produce

positive voltage on Pin

(See Figure

and Page

4.)

High Impedance: Positive pressure on diaphragm produce

positive voltage on

(See Figure

and Page

4.)

^IPTRIDBE

TQANSIDRMER

CABLE

RlrlSSKINAL

IIREI-PIX

bmlC

CONNECiOm

IIIPEWL SELLC~V~N

sacnir

iinoww

:3*

eSNCE

00911Vi

Built-in magnetic reed On-Off switch with lockplate installed

in unlocked position. To lock switch in On position, move

plate

180".

Retighten screw.

Switch:

GUARANTEE

This Shure product is guaranteed In normal use to be free from electrical and

mechanical defects for a perlod of one year from date of purchase. Please re-

tain proof of purchase date. This guarantee includes all parts and labor. This

guarantee is in lieu of any and all other guarantees or warranties, express or

implied, and there shall be no recovery for any consequentlal or ~ncldental

damages.

SHlPPiNG

INSTRUCTIONS

Carefully repack the unit and return it prepaid to:

Shure Brothers Incorporated

Attention: Service Department

1501

West Shure Drive

Prllngton Heights, Illinois

60004

If outs~dethe United States, return the unit to your dealer or Authorized Shure

Service Center for repair. The unit will be returned to you prepald.

IMODEL PES€iD.CN SPECIF1CATIONS (Continued)

Connector: Equlpped with professional three-p~naudio connector (male)

designed to mate wlth furnished cable or Cannon

serles,

Switchcraft A3

(Q.G.)

series or equivalent connectors

Shock Mount: Internal rubber vibrat~on-isolator

Swivel Adapter: Adjustable through 90' from ver!ical to horizontal, to

5/8"-27 stand thread

Cable: 7.6m (25 ft) two-conductor shielded, TRIPLE-FLEX@, detach-

able, with professional three-pin audio connectors (male

and female)

Net Weight: 298 grams (10% oz) less cable

PackagedWeight: 1.72 kilograms (3 Ib 12% oz)

FURNISHED ACCESSORIES

Swivel Adapter: A25B

Carrying Case: 90M1404

OPTIONAL ACCESSORIES

Desk Stand: Models 5338, S37A, 5388, S39A, S40A

Disconnect

Adapter: Model A45

Line Matching

Transformer: Model A95 Series

Windscreen: Model A61WS

REPLACEMENT PARTS

Cartridge: R65

Cable: C51CN

Switch: RKlO6S

Grille Assembly:

RS65

Plug Elemenl: RK4CP

Case Assembly: RK15OC

AREA CODE 312/866-2200 CABLE SHUREMICRO

@HH

SHURE BROTHERS

INC.

222

HARTREY AVENUE

EVANSTON, ILLINOIS

60204

U.S.A.

Shure Brothers Inc. U.S. Patents 3,132,713

27A1295 (TD) and 3,240,883

Inhaltsverzeichnis

Andere Shure Mikrofon Handbücher

Shure

Shure 710A Series Bedienungsanleitung

Shure

Shure 14A Bedienungsanleitung

Shure

Shure MX150/C Bedienungsanleitung

Shure

Shure Ranger 2 series 414a Bedienungsanleitung

Shure

Shure SM57 Bedienungsanleitung

Shure

Shure PGA 98D Bedienungsanleitung

Shure

Shure 527A Bedienungsanleitung

Shure

Shure MV88+ Bedienungsanleitung

Shure

Shure 520DX Bedienungsanleitung

Shure

Shure LEGENDARY PERFORMANCE MV88 Bedienungsanleitung

Shure

Shure BG 1.0 Bedienungsanleitung

Shure

Shure Unidyne B 515BG Bedienungsanleitung

Shure

Shure PE15H-LC Bedienungsanleitung

Shure

Shure PGA81 Bedienungsanleitung

Shure

Shure 588SA Bedienungsanleitung

Shure

Shure BETA 58A Bedienungsanleitung

Shure

Shure BETA 87A Bedienungsanleitung

Shure

Shure R193 Bedienungsanleitung

Shure

Shure Microflex MX200 Series Bedienungsanleitung

Shure

Shure 33-44 Series Bedienungsanleitung

Shure

Shure Microflex MX100 Series Bedienungsanleitung

Shure

Shure SM57 Bedienungsanleitung

Shure

Shure CVG Series Bedienungsanleitung

Shure

Shure Easyflex EZG Series Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

JLab

JLab GO TALK Bedienungsanleitung

Renkforce

Renkforce TY-109 Bedienungsanleitung

Trust

Trust 31008 Bedienungsanleitung