Shure R180 Bedienungsanleitung

1/4

R180 -- Replacement Cartridge

General Description

Shure Model R180 Replacement Cartridge For

Models 588SDX, 515SDX, 515SBGX, 515SBG-18X,

515SBG-18XF, and 515BSLX

This kit contains the following:

•One R180 replacement cartridge

•Two pieces of shrink-wrap tubing (for 515SBGX, 515SBG-8X, 515SBG-8XF, and 515BSLX only)

The following tools are needed to replace the cartridge:

•Long-nose pliers (for 588SDX and 515SDX only)

•A soldering iron of 25 to 40 watts

•Wire cutters (for 515SBGX, 515SBG-18X, 515SBG-18XF, and 515BSLX only)

•#4 (.050 in., 1.3 mm) hex wrench (supplied with 515SBGX, 515SBG-18X, 515SBG-18XF, and 515BSLX only)

Shure Incorporated

2/4

Models 588SDX and 515SDX

Wiring Diagram

It is recommended that the following procedure be performed on a table or other flat surface to support the car

tridge and case in order to avoid the possibility of breaking the cartridge leads.

To replace the R180 cartridge in the 588SDX and 515SDX, proceed as follows:

1. Unscrew and remove the grille (turning counterclockwise).

2. Gently pull out the old cartridge, being careful not to break the leads.

3. Using a Phillips screwdriver, remove the screws and lock plate which hold the switch in place.

4. Using long-nose pliers, gently pull out the switch, being careful not to break the leads.

5. Unsolder and remove the leads of the old cartridge from the switch.

To prevent damage to the switch, soldering iron between 25 and 40 watts is recommended.

6. Solder the lead closest to the RED dot on the new cartridge (see wiring diagram above) to the terminal with the

YELLOW lead on the switch.

Shure Incorporated

3/4

7. Solder the other lead from the new cartridge to the terminal with the BLUE lead on the switch.

8. Using longnose pliers, carefully replace the switch in the case with the blank terminal on the switch facing to

wards the cartridge (to ensure the UP position is ON), being careful not to pinch the leads.

9. Placing your finger inside the case to support the switch, secure the switch in place by screwing the nonlock

plate screw on the side of the switch closest to the grille.

10. Gently insert the new cartridge into the case, being careful not to pinch the leads, and making sure the foam

gasket on the cartridge is above the aluminum ring.

11. Replace and screw on the grille.

12. Replace the lockplate on the side of the switch opposite the grille, then secure it with the remaining screw.

Models 515BSLX, 515SBGX, 515SBG-18X, and 515SBG-18XF

It is recommended that the following procedure be performed on a table or other flat surface to support the car

tridge and case in order to avoid the possibility of breaking the cartridge leads.

To replace the R180 cartridge in the 515X Series (except the 515SDX), proceed as follows:

1. Slide the supplied shrink-wrap tubing over both leads on the R180 replacement cartridge.

2. Using a #4 (.050 in., 1.3 mm) hex wrench, loosen the setscrew on the base of the grille.

3. Unscrew and remove the grille (turning counterclockwise).

4. Gently pull out the old cartridge, being careful not to break the leads.

5. Using wire cutters, cut the lead from the old cartridge marked by the dot as close to the cartridge as possible,

so the lead sticks out from the handle. Mark the cut lead with a small piece of tape.

Shure Incorporated

4/4

6. Strip about 1/4-in. (6 mm) of insulation from the end of the lead.

7. Take the lead marked with a red dot on the R180 replacement cartridge and splice it to the taped lead, twisting

the stripped ends together.

8. Solder the spliced leads.

To prevent damage to the leads, a soldering iron of 25 to 40 watts is recommended.

9. Slide the shrink-wrap tubing so it entirely covers the soldered connection and bare wires. Gently rub the tip of

the soldering iron back and forth along the shrink-wrap tubing until it shrinks.

10. Using wire cutters, cut the other lead of the old cartridge as close to the cartridge as possible, so the lead sticks

out from the handle.

11. Strip about 1/4-in. (6 mm) of insulation from the end of the lead.

12. Take the unmarked lead on the R180 replacement cartridge and splice it to the second lead of the handle,

twisting the stripped ends together. Solder the leads.

13. Slide the shrink-wrap tubing so it entirely covers the soldered connection and bare wires. Gently rub the tip of

the soldering iron back and forth along the shrink-wrap tubing until it shrinks.

14. Gently insert the new cartridge into the case, being careful not to pinch the leads, and making sure the foam

gasket on the cartridge is above the aluminum ring.

15. Replace and screw on the grille.

16. Using a #4 (.050 in., 1.3 mm) hex wrench, secure the grille by tightening the setscrew.

Do not torque the setscrew too tightly.

Inhaltsverzeichnis

Andere Shure Aufnahmegeräte Handbücher

Shure

Shure PS9 Bedienungsanleitung

Shure

Shure ML140HE Bedienungsanleitung

Shure

Shure ANI4IN Series Bedienungsanleitung

Shure

Shure M55E Bedienungsanleitung

Shure

Shure ANI22 Bedienungsanleitung

Shure

Shure AMS880 Bedienungsanleitung

Shure

Shure PSM 900 Bedienungsanleitung

Shure

Shure LEGENDARY PERFOMANCE MVi Bedienungsanleitung

Shure

Shure PSM 900 Programmierhandbuch

Shure

Shure Access Bedienungsanleitung

Shure

Shure DT15P Bedienungsanleitung

Shure

Shure MVX2U Bedienungsanleitung

Shure

Shure 44 Series Bedienungsanleitung

Shure

Shure PSM1000 Kurzanleitung

Shure

Shure ANI4IN Series Bedienungsanleitung

Shure

Shure PSM700 Bedienungsanleitung

Shure

Shure MV88+ Bedienungsanleitung

Shure

Shure ANIUSB-Matrix Bedienungsanleitung

Shure

Shure MVI Bedienungsanleitung

Shure

Shure PSM1000 Bedienungsanleitung

Shure

Shure P3RA Bedienungsanleitung

Shure

Shure A820-NIC-DANTE Bedienungsanleitung

Shure

Shure ANI22 Bedienungsanleitung

Shure

Shure M625 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch