SHYAM Networks WE100 Bedienungsanleitung

NETWORKS

www.shyamnetworks.com

WE100

Outdoor Wi-Fi AP/CPE

Quick Start Guide

For advanced settings and more detailed information, download the user

manual from www.shyamnetworks.com.

Package Contents

WE100 (main unit) 1

PoE Adapter 1

Ethernet Cable 1

Quick Start Guide 1

Optional

Table Top

Stand

Self Tapping

Screw

Plastic

Gitti

Worm Drive

Clamp

NETWORKS

WE100

MODEL Tx POWER LAN PORT

WE-1C-WM-17 17 dBm 1

WE-1C-WM-22 22 dBm 1

INTERFACE DESCRIPTION

Clamps • Center clamp for pole mounting.

• Top and bottom for wall mounting.

LEDs Indicates the working status.

LAN Port Provides connection through Cat5e cable.

RESET • Single press reboots the system.

• Press till all lights go off once, restores to factory

default settings.

Table Top Stand Provided for table mounting.

Available Models

Interface Description

1. Hardware Overview

Clamps for

Wall Mount

Clamp for Pole Mount

RESET Button

Table Top Stand

WE-1C-WM-17

LEDs

LAN Port

WE100

NETWORKS

LED Behavior

LED COLOR STATUS DESCRIPTION

PWR Green On WE100 is powered-on.

Off WE100 is powered-off.

WAN Green On Link is up.

Blinking Data transfer taking place.

Off No link present.

WLAN Green Blinking Indicates that the wireless mode is enabled.

By default, this LED glows.

RSSI Low Green On Indicates that the power level received by

the antenna is low.

RSSI Low + Medium Green On Indicates that medium power level received

by the antenna.

RSSI Low + Medium

+ High

Green On Indicates that high power level is received

by the antenna.

Caution and Warnings

• Use the PoE adapter included with the product. Using a different PoE adapter may

damage the product.

NETWORKS

WE100

2. Installing WE100 CPE

STEP 1 Connect one end of an RJ45 Ethernet cable to the LAN OUT port of the PoE

adapter and the other end to LAN of WE100 CPE.

STEP 2 Connect the second RJ45 Ethernet cable attached to the PoE adapter to a network

 device,suchastoaswitchortothesystemyouusetocongureWE100CPE.

STEP 3 Connect the PoE adapter to the main electrical supply using the power cord

provided with the PoE adapter kit. Now, turn on the power supply. PWR LED on

the back side of the unit glows. This indicates that WE100 CPE is receiving

power through the PoE adapter and that the connection between WE100 CPE

and your network has been established.

iNote: In case any LED does not operate, then refer to the “Quick Troubleshooting” section.

Congratulations! The installation of WE100 CPE is complete.

WE100 CPE

Pole

PoE AdapterSwitch

Pole

AP25

Computer

WE100

NETWORKS

3. WE100 CPE Mounting Instructions

STEP 1 Connect the RJ45 Ethernet cable to WE100 CPE

attached to the PoE adapter.

STEP 2 Placethetabletopstandonthedesiredatsurface.

STEP 3 Insert the WE100 CPE unit inside stand.

STEP 1 Connect the RJ45 Ethernet cable to WE100 CPE

attached to the PoE adapter.

STEP 2 Nail the plastic gittis in wall at proper position aligning

with WE100 CPE screw holes.

STEP 3 Screw the self tapping screws inside the plastic gittis.

STEP 4 Mount WE100 CPE over the self tapping screws.

Table Top

Wall Mounting

Pole Mounting

STEP 1 Connect the RJ45 Ethernet cable to WE100 CPE

attached to the PoE adapter.

STEP 2 Place WE100 CPE on the pole at proper position.

STEP 3 Attach the worm drive clamp to WE100 CPE along with

the pole and tighten it.

NETWORKS

WE100

4. Conﬁguring WE100 CPE

STEP 1 Power-up WE100 CPE.

STEP 2 CongureyoursystemwithIPaddressbetween192.168.1.2 to 192.168.1.253

and subnet mask to be 255.255.255.0.

STEP 3 Type the http://192.168.1.1 URL in the Internet Explorer 6.0 or above version to

access the web interface.

STEP 4 Provide user name as admin and password as password.

STEP 5 Click Setup Wizard in the navigation panel to view the Setup Wizard page.

Please refer to “WE100 Conguration and User Guide” for more details.

WE100

NETWORKS

5. Quick Troubleshooting

PROBLEM PROBABLE REASON RESOLUTION

The WLAN LED is not

blinking when WE100

CPE is powered-up.

The WAN connectivity

is down.

Check if all cables are

plugged properly.

The LED

corresponding to a

specicportis‘Off’.

WE100 CPE has no power. • Ensure that the power cord is

properly connected WE100 CPE.

• Ensure that the PoE adapter

is properly connected to the

functioning power outlet.

• Ensure that you are using the

same PoE adapter supplied

with WE100 CPE.

iNote: If none of the above

works, press the RESET button

on WE100 CPE to restore the

factory default settings.

NETWORKS

WE100

Warranty

This warranty is valid upto 12 months from the date of purchase.

Any manufacturing defect will be repaired by the company free of charge within the period of

warranty subject to the following conditions:

1. Thiswarrantycardmustbedulylledin,stamped&signedbythedealer.Thecardandthe

relevantcashmemomustbepreserved&producedalongwiththedefectiveunit.

2. Once the defective unit is repaired during the said warranty period, the warranty shall thereafter

continue only for the unexpired period to the original warranty.

3. This warranty is not valid for

• Damage resulting from accidents, mishandling, negligence, tampering, unauthorized repair,

failuretofollowinstructions,lightning,reandactofGod.

• Items not purchased from Authorized Dealers of the Company.

• Batteries (including rechargeable) wherever applicable.

• Damage to the tamper proof seal.

4. In case of a problem with your unit, please contact Customer Care. In the event that you are

advised to send and collect the unit from the Service Center of the Company – the same will be

done at your expense.

5. While Company or its Authorized Service Dealer will make every effort to carry out repairs under

this warranty as soon as possible, it is expressly made clear that the company shall not be held

liable for any direct or indirect loss to user due to delay in providing this service.

6. This warranty excludes every condition/warranty/liability not expressly set out therein.

7. Claims, if any to this warranty shall be subject to the courts having jurisdiction in Delhi, India.

Product ______________________________________________________________________

Model No. _______________________________ Serial No. ___________________________

Dealer’s Stamp & Signature Customer Care,

Shyam Networks (A Division of Vihaan Networks Ltd.)

21-B, Sec-18, Udyog Vihar, Gurgaon-122015

Haryana, India

Email: customer[email protected]

All India Helpline No. - +91 124 309 2000 Ext. 2009,

+91 9873573710

Manufactured by Vihaan Networks Ltd. Gurgaon, Haryana, India

109.00016.00

SN/QS/WE100/06/11/R2

Inhaltsverzeichnis

Andere SHYAM Networks Drahtloser Zugangspunkt Handbücher

SHYAM Networks

SHYAM Networks AP25-1C-E Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung