SI Dynamic 2TB Bedienungsanleitung

Installation Manual

Dynamic 2TB

Exclusively Distributed by

Dynamic 2TB Installation Manual – Revision – DRAFT

PLEASE READ PRIOR TO INSTALLATION

Before installation of this projection screen you should fully read these instructions to ensure you

are aware of the full installation procedure. In addition to the screen and accessories and in order to

carry out the installation you will need:

•Spirit Level

•Philips Screw Driver

•Suitable screw fixings of at least 70mm long if the wall which is being fixed into is not a

wooden structure.

In the Installation accessories you will find:

•White Cotton Gloves to be used at all times when handling the white screen fabric

•Fabric Installation tool

•70mm fixing screws

It is recommended that at least 2 people install the screen as larger screens can be heavy and

awkward to lift. Good lifting practices and lifting aids should be used as required to aid installation.

Important Notes

The symbols below show important notes that must be read and understood at each stage of

installation

= Warnings (Safety or Installation Quality)

= Information (Installation requirements or tips)

Dynamic 2TB Installation Manual – Revision – DRAFT

Unpacking

Do not unpack each piece from its protective packaging until you are ready to install it. This

will ensure that you do not damage any of the velvet finished pieces accidentally during installation.

Note that the Dynamic 2TB is designed to be assembled on the wall so that a clear floor area

big enough to build the screen is not required. However it can also be built on the floor if preferred

you will gust need to follow the same instructions but substitute the wall for the floor then lift and

attach the screen to the wall once built. DO NOT built the screen face down on the floor under any

circumstances as this will result damage to the screen and mechanism.

The screen is a 4 part frame. Two ‘C’ sections that make the Top and Bottom of the screen with the

masks incorporated and the left and right sections that join the top and bottom sections. The right

section also has all the electrical connections.

Frame Section Configuration Fig. 1

Note that the screen will ship with a separate box for the two ‘C’ section covers that make up

the completed velvet frame.

Dynamic 2TB Installation Manual – Revision – DRAFT

Installation

•Decide on the height you want the bottom of your finished screen to be from the finished

floor level (FFL). Now add 28mm from the FFL to bottom of screen height and mark a level

line on the wall at this height. This will be the height of the screw holes for the bottom.

•Now mark the central left to right point for the screen (normally the centre line of the room.

This will be the centre of the Bottom screen section.

•Now using these lines to position the central section of screen labelled ‘BOTTOM’ fix this to

the wall using the 70mm screws and countersunk washers provided. The screw holes are

located in the middle of the main aluminium cross brace marked ‘Fixing Point’. Do not over

tighten these as that will bend the frame, they should just contact the frame. Use a spirit

level to ensure that this section is level and central. This is very important as it will form the

basis for the rest of the screen to be built to.

•Now fix through the slot in the black mount plate on both sides of the bottom section. Again

do not over tighten these as the green foam behind is designed to allow the screen to ‘float’.

•Prepare the right end section to be fitted. There are two joining sliders which join the

bottom section and right section. These can be secured in place using the grub screws to

stick out of one of the profiles half way.

•Now lift the left section and mate the joining slider into the respective profile until the two

ends of the profile meet fully.

•Using a spirit level check that the section is vertical.

Dynamic 2TB Installation Manual – Revision – DRAFT

Ensure that the feed wires to the screen come behind the right screen section towards the

centre of the screen as shown in the image above

•Screw the right section to the wall in the location marked ‘Fixing point’.

•Now fix the ‘Left’ section in exactly the same way again tightening the joining sliders using a

spirit level to check it is vertical.

•Fix the Top section to the Left and Right sections again with the sliders ensuring that you

tighten the grub screws and the fixing screws. Only fix through the points marked ’Fixing

Point’ and take care with the cable running across the top frame.

Dynamic 2TB Installation Manual – Revision – DRAFT

•You may need to slacken the screws on the Left /Right section while aligning the top

section to ensure that the joining sliders are able to fully engage. Ensure that the ends of

the two sections meet fully together.

•Mechanically you now have all the sections fitted to the wall.

Dynamic 2TB Installation Manual – Revision – DRAFT

Electrical Connections

•On the Right side section there are 4 connectors. 2 – Power and an signal XLR to connect

the bottom and 2 to connect the top. Make both all 4 of these connection. The mask power

simply pushes together. The signal XLR also pushes together.

•On the feed cables that go towards the middle of the screen there are 3 additional

connectors. These additional ones all come from the control box and should be routed

through the wall from the back of the screen.

•Connect the 8 Way power connector, screwing the connection together to ensure that it is

secure.

•Plug the two RG45 connectors together. Care should be taken to ensure that the RJ45

connections are connected correctly according to the colour coding on the plugs.

Mask Connections

The masks are tensioned via large spring mechanisms in the side sections. At each end of these

sections you will see a small hook.

•Pull the hook towards the mask taking care not to release the hook as it will be under spring

tension. Once you have pulled it right the way out to the mask hook the hook onto the small

wire loop attached to the mask bar.

Dynamic 2TB Installation Manual – Revision – DRAFT

•Do this for all 4 spring hooks at each end of both mask bars. Ensure that the mask are all

now under tension and that no wiring has become loose in transit or during installation that

will impede the travel of the mask bar along the linear bearing track it travels on.

Ensure that the tension wires are running vertically. If they are not you can slide the wire

fixing loop along the mask bar to make sure they are.

Screen Covers

•Fit the left and right ‘C’ section screen covers onto the magnetic plates. Note that at the top

corners of the screen there is a levelling Alan screw that the covers should sit onto. Ensure

that the cover is right back onto the magnets and that the joints are tightly pushed together.

Dynamic 2TB Installation Manual – Revision – DRAFT

Fabric Installation

Your screen is delivered with two fabrics; the black backing fabric and the main screen fabric. The

first one to be installed is the black backing fabric.

Care and time should be taken during handling and installation of the fabric. On larger screens

you will need 2 people to complete this task.

•Take the roll of backing fabric and the fabric installation tool. Start to unroll the fabric from

the roll by about 500mm. Holding the top corner of the fabric in one hand, line it up with the

top left hand corner of the screen so that the edges of the fabric are in line with the outer

edges of the screen frame.

•With the fabric tool push the tool onto the fabric and down into the grey plastic fabric

retaining track.

•

You may want to try pushing the fabric tool into the fabric retaining track without any fabric

first to get a feel for where it goes in and how much force is required.

Dynamic 2TB Installation Manual – Revision – DRAFT

Retaining track insertion point Fig. 8

•Now unwind enough fabric from the roll to take you to the middle of the screen. Again

ensuring that the top of the fabric is in line with the top of the screen push the fabric into

the fabric retaining track in the centre of the top rail of the screen.

•Now unroll the remainder of the black backing fabric and repeat the process of tucking the

fabric into the top right of the screen.

•You should now have the fabric hanging from the three tucked points on the top of the

screen.

•Now using one hand apply a little bit of tension to the fabric at the bottom in the middle and

then using the fabric installation tool tuck fabric into the centre bottom of the fabric

retaining track.

•Now repeat this process on in the centre of the left and then right sides. See Fig.9.

Fabric Tuck Order Fig. 9

•Now continue to tuck in the fabric along the length of the retaining track working out from

each central tuck. Only tuck max 300mm at a time in each direction and then go to the

opposing side and tuck the same amount. This will ensure an even stretch across all the

fabric.

Inhaltsverzeichnis

Andere SI Projektionsfläche Handbücher

SI 7 SERIES FIXED Bedienungsanleitung

SI Solo/Pro 2 Bedienungsanleitung

SI ZERO EDGE PRO Bedienungsanleitung

SI Short Throw Lift Motorized Screen Bedienungsanleitung

SI 7 SERIES FIXED Bedienungsanleitung

SI Solo 2 Bedienungsanleitung

SI Sensation Series Bedienungsanleitung

SI 7 SERIES FIXED Bedienungsanleitung

SI Solo 3 675 EXTERNAL INDOOR Bedienungsanleitung

SI Nano Box Bedienungsanleitung

SI 5 SERIES Bedienungsanleitung

SI Dynamic 4 Bedienungsanleitung

SI FIXED 5 Series Bedienungsanleitung

SI Zero-G Bedienungsanleitung

SI Dynamic 2 XL Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung