SI Solo 2 Bedienungsanleitung

Solo / Pro 2

Installation Instructions

110v AC Motors

Solo Pro 2Solo 2

Please use these QR

Codes to access the

updated installation

instructions and video

tutorials.

WARRANTY

Warranty

New SI products carry a standard 1- year warranty on

parts and labor.

FCC INFORMATION

This device complies with Part 15 of the FCC Results. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including that which may

cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for

CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment.

Changes or modifications not expressly approved by the manufacturer could void

the user's authority to operate the equipment.

INITIAL CONSIDERATIONS

Thank you for your purchase of Solo/Pro 2. The screen

is mountable outdoors, but is not waterproof. It has not

been designed to be run or left in the rain or condensing

humidity. Also avoid water spray, splash and extreme

heat or cold. Protect your Solo/Pro 2. and you can expect

years of quality use.

For a quick install it is recommended you run appropriate

wire to the installation location before installing the

screen. See the Pre-Wire sections for details.

Follow all local electrical codes when running and

terminating AC(110v) wires. It is the responsibility of the

installer to make sure AC(110v) screens are installed to

electrical safety codes.

The Short Throw material is not 100% opaque.

Light sources behind the screen may be visible in

the viewing surface.

Initial Considerations

CONTENTS

AC(110v) RTS - Parts In The Box 4

AC(110v) 485 - Parts In The Box 5

Spacer Blocks & Leveling Shims 6

Pre-Wire - AC(110v) 485 7

Installation 8

Flatten The Material At The Weight Bar 17

AC(110v) Rts 18

Programming - AC(110v) Rts 19

Pairing Another Rf Remote 21

Using Original Remote 21

Programming AC(110v) 485 - With Decoset (Incl.) 22

Screen With UAI+ / SI.FI Block Diagram 25

Control AC(110v) 485 With 3rd Party - Via Serial 28

Using 485 Motor Interface With Fontus For 3rd Party Controls -

AC Motors 29

Using 485 Motor Interface With Fontus For 3rd Party Controls -

CONTENTS

LV Motors 30

Control 485 With 3rd Party (Wet Contact) Via Fontus 31

Control 485 With 3rd Party (Dry Contact) Via Fontus 32

Control 485 With 3rd Party (IR) Via Fontus 33

Control 485 With 3rd Party (IR) Via Fontus - Programming 34

Control 485 Screens With Included Decoset Keypad 36

Control AC(110v) 485 With 3rd Party - Via IP Controller 37

Control AC(110v) 485 With 3rd Party - Via DCT 39

Mounting Accessories 41

(Purchased Separately) 41

Motor Accessories - AC(110v) Rts/ 485 (Purchased Separately)

Storage And Transport 43

Care And Maintenance 45

Troubleshooting 46

AC(110v) RTS - Parts in the Box

RF Remote

AC(110v) RTS - Parts in the Box

(2) Ceiling/Wall

Locking brackets

(6) Leveling Shims

PWR Solo/Pro 2 screen

(6) Wood

fasteners

(6) Leveling Shims

Coupler

AC(110v) 485 - Parts in the Box

(6) Wood

fasteners

Additional

accessories

required for 485

control (pg. 42)

Solo/Pro 2 screen

485

PWR

(2) Ceiling/Wall

Locking brackets

Decoset &

Interface

Bracket

SET UPPER

SET LOWER

REVERSE

DOWN

STOP

485 Motor Interface

485 Motor only

Spacer Blocks & Leveling Shims

SPACER BLOCKS & LEVELING

SHIMS

Spacer Blocks are used to

clear an obstruction on the

wall. Connect spacer block

to each wall bracket before

installation.

Leveling Shims are used if

the ceiling or other

mounting surface is out

of level or plumb. Connect

to ceiling brackets before

installation.

7Pre-Wire - AC(110v) 485

PRE-WIRE - AC(110v) 485

1. Run 3 conductor wire/Cat 5e to the left side of

screen cassette installation location (refer to pg. 9).

To be sure you have the correct wire you can order

485 wire directly from SI.

2. Terminate the wires with the provided terminal block

as shown below.

Data +

Data -

Data ground

Not Used

RS485 (+)

RS485 (-)

Power from motor 7v DC

Ground

Pin 1

Pin 8

Proper mounting preparation will ensure a great

installation. Mounting brackets must be level to each

other, as well as plumb. They must be screwed into

structural members of some kind, such as ceiling

joists or wall studs. You may use the wood screws

provided, or other anchors (not provided) capable of

carrying the load, that is suitable to the substrate.

DO NOT MOUNT TO HOLLOW SHEET ROCK.

1. The drop is adjustable in the field between 0'' and

the MAX DROP (12'', 24'', or 36'', 2'' for short throw)

ordered for your screen. Use the drawing (refer to

pg. 7) to pick a bracket height that will allow you to

extend your screen to achieve the desired vertical

position of your viewing area.

INSTALLATION

Solo/Pro 2 - Installation

Andere Handbücher für Solo 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SI Projektionsfläche Handbücher

SI 7 SERIES FIXED Bedienungsanleitung

SI Dynamic 2 XL Bedienungsanleitung

SI Sensation Series Bedienungsanleitung

SI Solo/Pro 2 Bedienungsanleitung

SI ZERO EDGE PRO Bedienungsanleitung

SI Nano Box Bedienungsanleitung

SI ZERO EDGE PRO Bedienungsanleitung

SI 5 SERIES Bedienungsanleitung

SI 7 SERIES FIXED Bedienungsanleitung

SI Zero-G Bedienungsanleitung

SI 7 SERIES FIXED Bedienungsanleitung

SI Short Throw Lift Motorized Screen Bedienungsanleitung

SI Dynamic 2TB Bedienungsanleitung

SI FIXED 5 Series Bedienungsanleitung

SI Dynamic 4 Bedienungsanleitung

SI Solo 3 675 EXTERNAL INDOOR Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch