10. Manual Recording
8. UPnP
9. NAT
11. Playback
“Online” status means connecting the device successfully and you will
see the live image. You may select the added device and click button to
modify channel, IP address, ect.
Del et eEdit
Display Password
IP Camera Name
IP Address
Model
Edit IP Camera
XXX
192 .168 . 1 . 58
9008
admin
XXX
Port
Username
Protocol
Password
IP Chann el 5
OKTest Cancel
1
2
192.168.1.20IP Channel 4
192.168.1.38IP Channel 3
XXX
9008 XXX
Online
XXXOffline XXX900 8
Remain Bandwidth: 85 / 120 Mb
No. Camera Name IP Address Port Protocol Model Preview
Status
Edit Camera Edit Camera Group
Search Camera
3
192.168.1.45IP Channel 5
XXXOnlin e XX X9008
►WAN
①Set the network of the NVR. Go to Start →Settings →Network → TCP/IPv4.
Input static IP address or enable PPPoE and then input the user name and password
received from your ISP.
②Go to Start → Settings → Camera. Click “Add Camera” or behind the
column of the search camera and select “ManuallyAdd” to add the IP cameras.
Input IP address, server port, username and password of the IP camera. The IP
camera must be connected over WAN. And here the IP address of the IP camera
must be a WAN IP address.
►NAT Settings
①The NVR shall be powered on and connected to the network.
②Go to Start →Settings → Network → TCP/IPv4. You can obtain the IP
address, subnet mask and gateway automatically. You can also manually enter
them according to the actual network situation. Please make sure the network
segment is the same as that of the network which is used.
③Set the preferred or alternative DNS Server. Click “Apply” to save the
parameters.
④Go to Start →Settings → Network → NAT tab. Enable NAT and select
the NAT Server (The default NAT Server is nat.autonat.com ). Click
“Apply” to save the parameters.
TCP/IPv4 Port UPnP NAT
DDNS E-mai l Network Statu s
nat.autonat.com
NAT Server
Enable
Apply
►NAT Access
After finishing the NAT settings, you can input http://www.autonat.com/n9000
in the IE address bar and then press enter to go to the following interface. If
you are the first time to access the NAT, you shall download and install the
ActiveX according to the popup tips. After installing ActiveX successfully,
it will pop the login box.
Before recording, please install and format a HDD. In the live interface
you can see the menu toolbar. Click button to start recording. Click
it again to stop recording. You can also click to check the status of
the recording.
►Instant playback
Click “Instant Playback” in the right-click menu of the camera’s preview
window to select or drag the playback progress bar to change the playback
time to play back the record.
►General playback
Click on the tool bar at the bottom of the live preview interface or click
Start →Playback to go to the playback interface as shown below. You can also
add the playback cameras manually. Click in the playback window to pop
up the “Add Camera” window. Check the cameras in the window and then click
“Add” to add playback camera. The record files of the added playback camera
will be played in the playback interface.
You can use the UPnP function to enable the fast connection of the device to
WAN via a router without port mapping.
①Go to Start →Settings → Network → UPnP, and enable UPnP and then
click “Apply” button to save.
②Enable the UPnP function in the router.
③Click “Refresh” button to refresh the UPnP status. If the UPnP status were
still “Invalid UPnP” after refreshing it for several times, the port would be wrong.
Please change the mapping type to “Manual” and then click to modify the
port until the UPnP status turns to “valid UPnP”.
HTTP Port
Server Port
80
6036
80183.17.254.19 Valid UPnP
Valid UPnP
Invalid UPnP
6036183.17.254.19
Port Type External Port External Address UPnP Status Edit
Port
RTSP Port
554
554
TCP/IPv4 Port UPnP
DDNS E-mai l NAT Network Statu s
AutoMap Type
UPnP
NAT
Enable
Refresh Apply
Device Serial Number : Click on the menu bar at the bottom of the live
interface to check the serial number or go to Start →Settings → Network →
Network Status to check the serial number of the NVR).
User Name : The username of the NVR. The default username is admin.
Password : The password of the NVR. The password is set by yourself when
you configure the wizard for the first time.
Enter Password
Enter Password
Enter device serial number
Login
