SidePilot Mav GoPro Bedienungsanleitung

Mav GoPro Remote Controller User Manual

v1.0 Page 1

Mav GoPro

Remote Controller

User Manual

Rev v1.0

24/05/2022

Mav GoPro Remote Controller User Manual 
v1.0 Page 2 
Contents 
Overview .............................................................................................................................................3 
Installation Instructions .......................................................................................................................4 
Instructions for use..............................................................................................................................4 
Mission Planner Plugin ........................................................................................................................4 
Web Interface......................................................................................................................................5 
Firmware .............................................................................................................................................5 
Current Firmware version: v1.0 .......................................................................................................5 
Firmware Update.............................................................................................................................5 
Troubleshooting ..................................................................................................................................6 
‘I am unable to control my GoPro! Please Help!’ .............................................................................6 
FAQ......................................................................................................................................................6 
Advanced.............................................................................................................................................7 
Configuration...................................................................................................................................7 
Web UI GoPro Control .....................................................................................................................7 
Controlling a specific GoPro.............................................................................................................7 
MAVLink Connection Details............................................................................................................7 
Pin diagram:.....................................................................................................................................8 
 
 

Mav GoPro Remote Controller User Manual

v1.0 Page 3

Overview

The Mav GoPro Remote Controller (MGRC) plugs into a flight controllers MAVLink serial port,

allowing you to control your GoPro camera using MAVLink commands via ground station or RC

control. Note: It does NOT enable any sort of video feed from GoPro, it just does command/control.

The MGRC uses the OpenGoPro BLE protocol to send commands to GoPro, enabling easy and

reliable use, and uses the MAVLink protocol to speak to the flight controller (ArduPilot or PX4).

Compatible with the GoPro HERO10 Black, HERO9 Black, Max, HERO8 Black, HERO7 Black, Fusion,

HERO6 Black and HERO5 Black.

This product and/or service is not affiliated with, endorsed by or in any way associated with GoPro Inc. or its products and

services. GoPro, HERO, and their respective logos are trademarks or registered trademarks of GoPro, Inc.

Mav GoPro Remote Controller User Manual

v1.0 Page 4

Installation Instructions

Installing the MGRC is easy, just follow these steps:

1. Change your flight controllers’ parameters using a GCS such as Mission Planner, set the

following parameters:

Parameter

Value

SERIALX_PROTOCOL

SERIALX_BAUD

Where X is the serial port you are plugging the MGRC into.

2. Turn off your flight controller and plug the Mav GoPro Remote Controller into the desired

serial port using the included cable.

3. Turn on your flight controller and GoPro.

4. On your GoPro go to Preferences -> Connections -> WiFi Band and ensure it is set to 2.4GHz.

5. On your GoPro go to Preferences -> Connections -> Connect Device and select GoPro App'.

6. Pairing will begin and it will pick up the MGRC automatically. When pairing, the red LED will

flash fast (If not flashing fast/paired within 20 seconds, press the MGRC reset button).

7. You are done! The red blinking light will turn solid when it has successfully connected to the

camera. You can now control the shutter (take video, or start/stop recording) via a Trigger

Camera action in Mission Planner.

Instructions for use

Once the above installation steps are followed, for using the device in the future, simply turn on

your flight controller/drone with the MGRC connected! It will automatically reconnect to your GoPro

if in range (may need to be switched on manually), indicated by the solid red led on the MGRC. If it

does not go solid after a minute or two, you may need to restart GoPro or restart the WiFi

connection by tapping the ‘RST’ button.

Mission Planner Plugin

A plugin for Mission Planner program is available for download here. This allows the user to easily

trigger the shutter, and change between Photo/Video/Timelapse modes. You can install this by

placing the .cs file downloaded above into the plugins folder (usually located at C:\Program Files

(x86)\Mission Planner\plugins\) and restarting mission planner. To use the plugin, right click the map

and hover over the ‘MavGoPro RC Control’button.

Mav GoPro Remote Controller User Manual

v1.0 Page 5

Web Interface

The MGRC provides a web interface where you can check the MAVLink status, as well as GoPro

information such as its current mode and battery status.

This interface is activated by tapping the ‘OPT’ button on the MGRC. A WiFi network will be started

called ‘MAV-GOPRO-RC’. Connect using your smartphone or PC, and navigate to

http://10.71.79.1/info

SSID: MAV-GOPRO-RC

Password: MavlinkGoProRC

Firmware

The MGRC firmware is updatable via a web upload. Only update packages provided by us can be

installed, and will be available via the https://store.sidepilot.net website.

Current Firmware version: v1.0

Firmware Update

1. First download the firmware update .bin file from the store.

2. Turn off your GoPro and remove the battery (to avoid it automatically turning on again).

3. Connect your phone/computer to the ‘MAV-GOPRO-RC-BLE’ WiFi network (enabled by

tapping the ‘OPT’ button).

4. Navigate to http://10.71.79.1/update

5. Tap on ‘Browse’ and select the .bin firmware file.

6. Tap ‘Update’ and wait. The Green and Red LED’s will flash while updating. The update

process usually takes 20-30 seconds and the MGRC will automatically reboot when

completed. The Web interface may not update upon reboot.

7. Verify the installation was successful by navigating to http://10.71.79.1/info and check

the revision number.

Mav GoPro Remote Controller User Manual

v1.0 Page 6

Troubleshooting

‘I am unable to control my GoPro! Please Help!’

•If the RED (BLE) LED is flashing slowly, it is not connected to GoPro. Steps to resolve in order

are:

1. Restart GoPro

2. Turn off GoPro, remove battery and wait 10 seconds. Reinsert and turn on.

3. Re-pair GoPro and MGRC. Follow the installation instructions for pairing.

4. Reset GoPro Connections in Preferences -> Connections -> Reset Connections.

5. Contact [email protected]t

•If the RED (BLE) LED flashes quickly but never turns solid, ensure the GoPro WiFi is set to

2.4GHz and re-pair the GoPro and MGRC.

•If the RED (BLE) LED is bright and steady (not flashing), but the GREEN (MAV) LED is not

flashing at all, then there is no communication between your drone and MGRC. Check that

the flight controller parameters are set as per the installation instructions. Flight controller

may need to be restarted after changing parameters.

•RED (BLE) LED is stable, GREEN (MAV) LED is flashing, but I still cannot control my GoPro at

all! In this case, please contact t[email protected] with you GoPro model including its

firmware version and Flight controller firmware version. Ideally also a video showing this

behaviour.

FAQ

Just some of the most common questions asked:

Q: What is the blinking green (MAV) LED underneath?

A: This is the MAVLink connection indicator of the MGRC and lights up when a MAVLink data packet

is recieved. If it is not blinking ‘randomly’, and you are unable to control your GoPro, you should

double check your parameter settings.

Q: I want X feature/Why doesn’t this do X??

A: All feedback and improvement suggestions are welcome! Please contact tom@sidepilot.net, we

are happy to hear from you!

Mav GoPro Remote Controller User Manual

v1.0 Page 7

Advanced

Configuration

The MAVLink System and Component IDs can be manually changed by enabling the web interface

and navigating to http://10.71.79.1/config

Web UI GoPro Control

GoPro commands are able to be sent directly from the web UI, by navigating to

http://10.71.79.1/control

Controlling a specific GoPro

Some users may have multiple GoPro’s, which may cause the MGRC to not reliably connect to the

desired GoPro, due to how MGRC will search and connect to the first available GoPro. It is possibly

to specify the only GoPro to connect to by connecting to the ‘MAV-GOPRO-RC-BLE’ WiFi network

(Tap the ‘OPT’ button to enable this), and navigate to http://10.71.79.1/pair and entering ‘GoPro

XXXX’ where XXXX is the last four digits of your GoPro serial number. This can be found easily by

pairing the MGRC to the GoPro and going to http://10.71.79.1/info and seeing the GoPro Name

section. If unchanged, it is also the last four digits of the GoPro WiFi network.

MAVLink Connection Details

Baud Rate = 57600

Protocol = 1

System ID = 1

Component ID = MAV_COMP_ID_CAMERA (#100)

Mav Type = MAV_TYPE_CAMERA

Autopilot type = MAV_AUTOPILOT_INVALID

Output:

MAVLINK_MSG_HEARTBEAT –1HZ

MAVLINK_MSG_GOPRO_HEARTBEAT –1HZ

Input:

COMMAND_LONG (#76)

➔COMMAND = MAV_CMD_DO_DIGICAM_CONTROL (203)

➔TRIGGER SHUTTER

➔COMMAND = MAV_CMD_DO_DIGICAM_CONFIGURE (202)

➔MODE

(0 = Photo, 1 = Video, 2 = Timelapse)

MAVLINK_MSG_ID_GOPRO_SET_REQUEST (#218)

Mav GoPro Remote Controller User Manual

v1.0 Page 8

➔CMD_ID == GOPRO_COMMAND_CAPTURE_MODE (1)

➔VALUE[0] == GOPRO_CAPTURE_MODE_XXX

(XXX = VIDEO/PHOTO/TIME_LAPSE)

➔CMD_ID == GOPRO_COMMAND_SHUTTER (2)

➔VALUE[0] == TRIGGER SHUTTER (1 = START, 0 = STOP)

Pin diagram:

The MGRC wiring header is a 6-pin JST-GH connector. The included cable (either 6-pin JST-GH to JST-

GH or 6-pin JST-GH to DF13) can be modified if other pin connections are required. The layout of the

cable is as follows (also labelled on the MGRC itself for reference):

Mav GoPro Remote Controller User Manual

v1.0 Page 9

Any other questions, please ask on the SidePilot

Facebook page, or send via email to

tom@sidepilot.net

Inhaltsverzeichnis

Andere SidePilot Fernbedienung Handbücher

SidePilot

SidePilot Solo GoPro Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung