Siecor 5000 Series Bedienungsanleitung

Artisan Technology Group is your source for quality

new and certied-used/pre-owned equipment

• FAST SHIPPING AND

DELIVERY

• TENS OF THOUSANDS OF

IN-STOCK ITEMS

• EQUIPMENT DEMOS

• HUNDREDS OF

MANUFACTURERS

SUPPORTED

• LEASING/MONTHLY

RENTALS

• ITAR CERTIFIED

SECURE ASSET SOLUTIONS

SERVICE CENTER REPAIRS

Experienced engineers and technicians on staff

at our full-service, in-house repair center

WE BUY USED EQUIPMENT

Sell your excess, underutilized, and idle used equipment

We also offer credit for buy-backs and trade-ins

www.artisantg.com/WeBuyEquipment

REMOTE INSPECTION

Remotely inspect equipment before purchasing with

our interactive website at www.instraview.com

LOOKING FOR MORE INFORMATION?

Visit us on the web at www.artisantg.com for more

information on price quotations, drivers, technical

specications, manuals, and documentation

View

Instra

Operating Instructions

for Fusion Splicer M90/Series 5000

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

The pages of these Operating Instructions will not be exchanged.

Modifications will be provided in the form of supplementary sheets.

Products subject to availability. Technical modifications reserved.

Edition 02/97

Published by

Siecor Corporation

489 Siecor Park

P.O Box 489

Hickory, NC 28603-0489

For US and Canada 1-800-743-2673

International 704-327-5000

FAX 704-327-5973

Printed in Germany

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Table of Contents 1 Getting to Know the M90 Splicer

2 Preparations

3 Parameters and Programs

4 Splicing

5 Attenuation Splice

6 Taking Out of Service

7 Troubleshooting and Maintenance

8 Accessories

9 Supplement / Modifications

Index

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Notes on these Operating Instructions

Please read these Operating Instructions carefully and note the recommendations they

contain. This will ensure your splicer remains free of fault. Use the information set out in

the Operating Instructions to perform the necessary regular care and maintenance of

your splicer. Avoid damage by using extreme care.

If you are in doubt about any points, contact the relevant service center. The trained

experts available at these centers should be able to assist.

Incorrect or incomplete maintenance can impair the operation of your splicer.

The manufacturer's warranty obligations for the splicer shall be rendered null and void if

the unit has been tampered with by unauthorized persons.

Warranty The Siecor M90 Fusion Splicer is warranted against defects in material and

workmanship for a period of one year from date of shipment. Any M90 found to be

defective during the warranty period may be returned, transportation prepaid, to the

factory for repair without charge.

This warranty does not apply to units which have been repaired or altered by an

unauthorized person, or which have been subject to misuse, negligence or accident.

A complete explanation of Siecor corporation´s warranties, and terms and conditions of

sale may be found on the reverse side of Siecor´s Quotations, Order Acknowledgement

and/or invoice forms and only the Warranty appearing thereon is to be considered

Siecor´s Warranty.

All inquiries regarding repairs or replacement parts should be directed to the Customer

Service Department, SIECOR CORPORATION, 489 Siecor Park, Hickory,

NC 28603-0489; (704) 327-5000. This will assure you the fastest possible service.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Definition of Warning Terms

Danger Within the scope of these Operating Instructions and the warning notices on the

products themselves, death, serious injury or substantial damage to property will occur

if the relevant precautionary steps are not taken.

Warning Within the scope of these Operating Instructions and the warning notices on the

products themselves, death, serious injury or substantial damage to property can occur

if the relevant precautionary steps are not taken.

Caution Within the scope of these Operating Instructions and the warning notices on the

products themselves, minor injury or damage to property can occur if the relevant

precautionary steps are not taken.

Note Within the scope of these Operating Instructions, important information on the product

or the relevant part of the Operating Instructions to which particular attention should be

paid.

Qualified

personnel Within the scope of these Operating Instructions, persons familiar with the

commissioning, operation and maintenance of electrical devices and possessing the

qualifications relevant for their work.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Password Request

The splicer must be opened in order to activate or deactivate the password request.

Danger

The fusion splicer or electrically operated accessories must not be opened except by

suitably qualified personal. Switch off fusion splicer. Pull power supply plug and 12-V

lead.

Open the front

panel see section 7.

Activating the

password re-

quest

The PC board which is now visible (see figure) contains a switch for activation or deac-

tivation of the password. If the password request is deactivated, the stored password is

deleted when the equipment is switched on again. However, the old password is re-

tained if you reactivate the password request before the equipment is switched on and

off. On renewed activation of the request there is no password stored. It is therefore

necessary to define a new password first (Parameter “Password”, see below).

M=23%

Switch “off”:

request acti-

vated.

Entering the

password A password consists of an arbitrary sequence of five input keys. If you try to change a

parameter while the password request is activated, the message “Enter password” ap-

pears. If an incorrect password is entered, the change of parameter is rejected. This

applies also to a change of password, i.e. a new password cannot be defined unless the

current password is known. To redefine the password, activate the parameter menu,

select the parameter “Password” and proceed according to the following flow chart:

Change password? Enter password?

Only if password already exists

Enter new password

Confirm password Password wrong

Operator menu

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Operating Instructions 1-1 M90 Fusion Splicer

Issue 02/97 Getting to Know the M90 Fusion Splicer

Getting to Know the M90 Splicer

Contents Page

Scope of Delivery.......................................................................................................................................1-2

General......................................................................................................................................................1-3

Fiber diameter.......................................................................................................................................1-3

Automatic fiber positioning....................................................................................................................1-3

Automatic fusion time control................................................................................................................1-3

Flexible software...................................................................................................................................1-3

Splicer shutdown...................................................................................................................................1-3

Accessories ..........................................................................................................................................1-3

Definition of X, Y, Z directions..............................................................................................................1-4

Overview of Modular Units.........................................................................................................................1-4

Modular units........................................................................................................................................1-4

Power Supply.............................................................................................................................................1-5

Overview...............................................................................................................................................1-5

Splicing Unit...............................................................................................................................................1-6

Overview...............................................................................................................................................1-6

LID system............................................................................................................................................1-6

Pigtail adapters.....................................................................................................................................1-7

Monitor and Control Panel..........................................................................................................................1-8

Monitor .................................................................................................................................................1-8

Control panel ........................................................................................................................................1-8

Inputs / Outputs.........................................................................................................................................1-9

Overview...............................................................................................................................................1-9

RS 232 interface...................................................................................................................................1-9

External video output ............................................................................................................................1-9

External LID input ...............................................................................................................................1-10

Case Lid ..................................................................................................................................................1-11

Overview.............................................................................................................................................1-11

Tool bag..............................................................................................................................................1-11

Technical Specifications...........................................................................................................................1-14