Siemens Retroline TH 192 Service-Handbuch

PowersTM Controls

Technical Bulletin

Document No. 155-231P25

TB-214

Rev. 2, December, 2001

TH 192 Adapter Kits

Siemens Building Technologies, Inc.

Description The TH 192 Adapter Kits are designed to convert most existing pneumatic room

thermostats to Powers TH 192 or 194 Series or Free Energy Band™TH 193 HC

Thermostats.

The Universal Adapter Kit contains the parts needed for all conversions. Adapter Kits

"A" and "B" do not contain all the parts that are included in the Universal Adapter Kit.

Therefore, kits "A" and "B" are suitable only for specific conversions.

See Table 1 to select the required kit and also to locate the page where the parts used

in a specific conversion are indicated.

Installation

Instructions The following general procedure applies for all thermostat installations. Notice that

some installations will require the use of the adapter frame to cover up paint lines,

broken walls, spots, etc. For installations not covered in this bulletin, remove the old

terminal and connect directly to the tubing. See Figures 2, 3 and 4.

General Procedure 1. Remove old thermostat from the wall.

2. Remove terminal head and gasket from fitting.

3. Clean fitting surface if required.

4. See Table 1 and locate page on conversion being made.

5. Identify correct mounting parts and necessary instructions.

6. Proceed with the connections required. Secure all connections and install plug-in

adapters to the 5/32-inch (4 mm) plastic tube. Use blue adapter for the air supply

line.

NOTE: Either the polyethylene (hard) or polyurethane (soft) tubing is

recommended on each specific conversion. This selection is based on

the most compatible application.

Technical Bulletin Powers Controls TH 192 Adapter Kits

Document Number 155-231P25

Rev. 2, December, 2001

Page 2 Siemens Building Technologies, Inc.

General Procedure,

Continued 7. Place the multi-slotted metal plate into the plastic frame (plastic frame may or may

not be needed), and attach to the terminal head or the wall using the screws and

slots indicated.

8. Obtain the thermostat mounting plate and screws from the thermostat box.

9. Loosely screw adapter base to multi-slotted plate.

10. Draw plastic tubing through the multi-slotted plate, adapter base and install plug-in

adapters on wall plate.

11. Using the key slotted holes, install wall plate on adapter base and fasten screws to

secure wall plate and adapter base.

12. Carefully plug in thermostats to wall plate.

NOTE: To facilitate plugging the thermostat into O-rings in the adapter, wet or

moisten the thermostat supply and return ports. This wetting or

moistening will lubricate and allow the thermostat to slip through the

O-rings more easily.

7. Install thermostat cover using Allen hex key tool P/N 192-497 to drive the two

screws that hold the cover in place.

8. When removing the thermostat from the wall plate, hold the thermostat firmly at the

top and bottom and start to pull the thermostat from the wall plate. At the same

time, use a screwdriver to pry wall plate latch arm away from the thermostat chassis

to release it. Do the same for the other side of the thermostat and pull the

thermostat away from the wall plate.

NOTE: Frequent removal and installation of the thermostat may bend the latch

arms beyond their operating positions. If this happens, bend the latch

arms back to their operating position before mounting the thermostat.

192-300 Universal Kit 192-483 Adapter Kit "A" 192-484 Adapter Kit "B"

Figure 1. Adapter Kits.

Powers Controls TH 192 Adapter Kits Technical Bulletin

Document Number 155-231P25

Rev. 2, December, 2001

Siemens Building Technologies, Inc. Page 3

Table 1. Adapter Kit Selection Chart. Use Kit No. 192-

Thermostat Type Type of Terminal Figure

Number 300 483 484

POWERS CONTROLS

TH 192 With Guard — 5

POWERS CONTROLS "D"

Model 5, HU 190, TT 180, HT 190 Flush 6 X

Flush Box 7 X

POWERS CONTROLS

TH 180, 182, 192 to convert from

horizontal to vertical installation Surface 7 X

Surface Box 8 X

HONEYWELL

HO, HP, TO, TP, TRO 900 Flush Box 9 X

Flush Banjo 10 X

HONEYWELL

TP 410, 910 to 924, 933 Mortar Joint 11 X

Flush Fitting 12 X

HONEYWELL

TP 901 A, B Plaster Back 13 X

HONEYWELL TP 901 C Mullion or Partition 14 X

HONEYWELL TP 931 Flush Electrical Box 15 X

Shallow Wall Box with

Plaster Ring 16 X

HONEYWELL

TP 970 to 974 Deep Wall Box 17 X

Flush Fitting 19 X

JOHNSON

T400,401,403,432,460,465,

H101, 102,103,105 Old Round Head 21 X

Surface Fitting 18 X

JOHNSON

H & T 4000, 5000 Flush Box 20 X

ROBERTSHAW

T18, T19, 32 Flush Box 22 X

Surface Fitting 23 X

ROBERTSHAW

H 10, 50, 52, T15, 16, 21, 25, 26,

30, 51, 52, Mortar Joint 24 X

Surface Box 26 X

Flush Electrical Box 28 X

BARBER COLMAN

TK1001, 1101, 1201,1301,

1501 Thru 1513,1521 Thru 1525 Mortar Joint 27 X

SWAN, BISHOP, BABCOCK Flush Fitting 21 X

DRAEGER (ITT), UPC See Note - X

0.125 O. D. Copper Tubing

Terminal Head Removed 4 X

Not listed in this Bulletin 0.187 O. D. Copper Tubing

Terminal Head Removed 4 X

NOTE: On Draeger Thermostats, the air lines are normally 5/32-inch O.D. plastic tubing and the multi-slotted plate

can be mounted using slots 1 and 14. On UPC Thermostats, the air lines are normally 1/4-inch O.D. plastic

tubing and the multi-slotted plate can be mounted using slots 12 and 13.

Technical Bulletin Powers Controls TH 192 Adapter Kits

Document Number 155-231P25

Rev. 2, December, 2001

Page 4 Siemens Building Technologies, Inc.

Figure 2. Thermostat Mounting with Universal Kit – Option 1.

Figure 3. Thermostat Mounting with Universal Kit – Option 2.

Powers Controls TH 192 Adapter Kits Technical Bulletin

Document Number 155-231P25

Rev. 2, December, 2001

Siemens Building Technologies, Inc. Page 5

Figure 4. Thermostat Mounting with Universal Kit – Option 3.

A. Cover C. (4) Anchor

B. Frame D. (4) Expander Nail

Installation Instructions

1. Put the flat side of frame against wall, mark the

four hole locations and drill them 1/4-inch × 1-inch

deep.

2. Insert the anchors through the frame and into the

hole. Then drive the expander nails in. If the frame

must be removed, the nails can be removed by

turning them counterclockwise.

3. Mount cover over frame and turn each end locking

screw five turns counterclockwise.

*See Field Purchasing Guide for Energygard ordering

information.

Figure 5. Universal Kit with Thermostat and Energygard* Model P Guard.

Technical Bulletin Powers Controls TH 192 Adapter Kits

Document Number 155-231P25

Rev. 2, December, 2001

Page 6 Siemens Building Technologies, Inc.

Required Parts for Installation

A. Terminal Plate (5-hole)

B. (2) Terminal Fitting

C. (2) Holder

D. (2) Gasket

E. (2) No. 6-32 × 9/16-inch

Long Flat Head Screw

F. (4) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic

Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No. 10 × 1-1/2 inch

Sheet Metal Screw

*K. Adapter Frame

*L. Adapter Base

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Figure 6. Powers Controls "D" Model 5, HU 190, TT 180, HT 190 Flush Box.

Surface Mounting Flush Box

Required Parts for Installation

F. (4) Tube Retainer

G. (2) 5/32-inch (4mm) Plastic Tube (Polyethylene- Hard) and Coil

H. Multi-slotted Plate

J. (2) No. 6-32 × 1-inch Long Binder Head Screw

*Items not shown. See Figure 2 for proper installation.

*L. Adapter Base

N. (2) Tubing Adapter (5/32-inch × 5/32-inch)

*P. (2) Plug-in Adapter

Figure 7. Powers Controls TH 180,182,192 Conversion From Horizontal To Vertical Installation.

Powers Controls TH 192 Adapter Kits Technical Bulletin

Document Number 155-231P25

Rev. 2, December, 2001

Siemens Building Technologies, Inc. Page 7

Required Parts For Installation

F. (4) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic

Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No. 6-32-inch × 1-inch Long Binder Head

Screw

L. Adapter Base

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper

installation.

Figure 8. Honeywell HO, HP, TO, TP, TRO 900 Surface Box.

Required Parts For Installation

F. (4) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No. 6-32 × 1-inch Binder Head Screw

K. Adapter Frame

*L. Adapter Base

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Required Parts For Installation

F. (2) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No. 6-32 × 5/8-inch Binder Head Screw

*L. Adapter Base

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Figure 9. Honeywell HO, HP, TO, TP, TRO 900

Flush Box. Figure 10. Honeywell TP 410, 910 To 924, 933

Flush Banjo.

Technical Bulletin Powers Controls TH 192 Adapter Kits

Document Number 155-231P25

Rev. 2, December, 2001

Page 8 Siemens Building Technologies, Inc.

Required Parts For Installation

F. (2) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Polyethylene- Hard) and Coil

H. Multi-slotted Plate

J. (2) No. 6-32 × 1-inch Binder Head Screw

*L. Adapter Base

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Required Parts For Installation

A. Terminal Plate (11-Hole)

B. (2) Terminal Fitting

C. (2) Holder

D. (2) Gasket

E. (2) No. 6-32 × 9/16-inch Flat-head Screw

F. (4) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No. 10 Sheet 6 –32 × 1-1/2 inch Pan Head Screws

*L. Adapter Base

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Figure 11. Honeywell TP 410, 910 To 924, 933

Mortar Joint. Figure 12. Honeywell TP 901A, B Flush Fitting.

Required Parts For Installation

A. Terminal Plate (11-hole)

B. (2) Terminal Fitting

C. (2) Holder

D. (2) Gasket

E. (2) No. 6-32 × 9/16 inch Flat-head Screw

F. (4) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No. - 6-32 × 1-1/2 inch Pan Head Screws

*L. Adapter Base

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Required Parts For Installation

F. (2) Tube Retainer

G. (1) 5/32-inch (4 mm) Plastic Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No. 6-32 × 1-1/2 inch Pan Head Screw

*L. Adapter Base

M. (2) Rubber Connecting Tube

N. (1) Tubing Adapter (1/4 × 5/32-inch)

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Figure 13. Honeywell TP 901A, B Plaster Back. Figure 14. Honeywell TP901C Mullion or Partition.

Powers Controls TH 192 Adapter Kits Technical Bulletin

Document Number 155-231P25

Rev. 2, December, 2001

Siemens Building Technologies, Inc. Page 9

Required Parts for Installation

*F. (2) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Polyethylene- Hard) and Coil

H. Multi-slotted Plate

J. (2) No.6-32 × 1-1/2 inch Pan Head Screw

*L. Adapter Base

N. (2) Tubing Adapter (5/32-inch x 5/32-inch or 1/4-inch ×

5/32-inch)

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Required Parts for Installation

*F. (2) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Polyethylene- Hard) and Coil

H. Multi-slotted Plate

J. (2) No.6-32 × 1-1/2 inch Pan Head Screw

*L. Adapter Base

N. (2) Tubing Adapter (5/32-inch × 5/32-inch or 1/4-inch x 5/32-inch)

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Figure 15. Honeywell TP 931 Flush Electrical Box. Figure 16. Honeywell TP 970-974 Shallow Wall Box

with Plaster Ring.

Required Parts for Installation

*F. (2) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Polyethylene- Hard) and Coil

H. Multi-slotted Plate

J. (2) No.6-32 × 1-1/2 inch Pan Head Screw

*L. Adapter Base

N. (2) Tubing Adapter (5/32-inch × 5/32-inch or 1/4-inch ×

5/32-inch)

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Required Parts for Installation

F. (2) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No.10 × 1-1/2 inch Sheet Metal Screw

*L. Adapter Base

M. (2) Rubber Connecting Tube

N. (2) Tubing Adapter (1/4-inch × 5/32-inch)

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Figure 17. Honeywell TP 970-974 Deep Wall Box. Figure 18. Johnson H & T 4000, 5000 Surface Fitting.

Technical Bulletin Powers Controls TH 192 Adapter Kits

Document Number 155-231P25

Rev. 2, December, 2001

Page 10 Siemens Building Technologies, Inc.

Required Parts for Installation

A. Terminal Plate (5-hole)

B. (2) Terminal Fitting

C. (2) Holder

D. (2) Gasket

E. (2) No. 6-32 × 5/8-inch Long Binder Head Screw

F. (4) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No. 6-32 × 1-inch Long Binder Head Screw

*L. Adapter Base

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Figure 20. Johnson H & T 4000, 5000 Flush Box.

Required Parts for Installation

A. Terminal Plate (11-hole)

B. (2) Terminal Fitting

C. (2) Holder

D. (2) Gasket

E. (1) No. 6-32 × 9/16-inch Flat-head Screw and

(1) No. 8-32 × 7/16-inch Long Binder Head Screw

F. (4) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Soft) and Coil

H. Multi-slotted Plate

J. (2) No. - 6-32 × 1-1/2 inch Pan Head Screw

*K. Adapter Frame

*L. Adapter Base

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Figure 19. Johnson T400, 401, 403, 432, 460, 465,

H101, 102, 103, 105 Flush Fitting.

Johnson Bishop

Swan (Old Round Head) and Babcock

E.(2) No. 8-32 × 7/16-inch E-(2) No.10-24 × 3/4-inch

Binder Head Screw Head Screw

NOTE: If terminal head is too close to the wall surface, loop

around plastic tubing as shown on Powers Controls "D"

Thermostat Installation. See Figure 6.

Required Parts for Installation

F. (2) Tube Retainer

G. (2) 5/32-inch (4 mm) Plastic Tube (Polyethylene- Hard) and Coil

H. Multi-slotted Plate

J. (2) No.6-32 × 1-1/2 inch Pan Head Screw

*L. Adapter Base

N. (2) Tubing Adapter (5/32-inch × 5/32-inch or 1/4-inch × 5/32-inch)

*P. (2) Plug-in Adapter

*Items not shown. See Figure 2 for proper installation.

Figure 21. Swan, Bishop & Babcock Flush Fitting. Figure 22. Robertshaw T18, T19, 32 Flush Box.

Andere Handbücher für Retroline TH 192

Andere Siemens Adapter Handbücher

Siemens

Siemens SIMATIC TS Adapter IE Bedienungsanleitung

Siemens

Siemens NK8223 Kurzanleitung

Siemens

Siemens SIRIUS 3RA1954-2C Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 5511 Bedienungsanleitung

Siemens

Siemens Gigaset 300 Bedienungsanleitung

Siemens

Siemens AC-ADPT Bedienungsanleitung

Siemens

Siemens 3VM9182-0SH10 Bedienungsanleitung

Siemens

Siemens Gigaset Powerline Adapter 200 Bedienungsanleitung

Siemens

Siemens Gigaset 108 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens 8US1261-6MT10 Bedienungsanleitung

Siemens

Siemens SIMATIC PG Bedienungsanleitung

Siemens

Siemens Gigaset 108 Bedienungsanleitung

Siemens

Siemens PS791-2AC Bedienungsanleitung

Siemens

Siemens Gigaset 300 Bedienungsanleitung

Siemens

Siemens 8US1213-4AH04 Bedienungsanleitung

Siemens

Siemens SIMATIC 6ES7 972-0CB20-0XA0 Bedienungsanleitung

Siemens

Siemens 8US1211-4TR00 Bedienungsanleitung

Siemens

Siemens BAAP Bedienungsanleitung

Siemens

Siemens 8US1211-1NS10 Bedienungsanleitung

Siemens

Siemens SIMOGEAR BA 203-KS Service-Handbuch

Siemens

Siemens SINAMICS Smart Adapter Compact Bedienungsanleitung

Siemens

Siemens Gigaset USB adapter 54 Bedienungsanleitung

Siemens

Siemens 7XV5450-0 A00 Series Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung