Siemens MDACT Bedienungsanleitung

INTRODUCTION

The Model MDACT from Siemens Industry, Inc. is a

multipoint serial dialer for use in MXL and FireFinder-

XLS systems where point identification of alarm,

supervisory, status or trouble indication is required at

central stations.

The MDACT has the following features:

• Multiple Data Protocols: Contact ID and SIA

• 100 Event History Buffer

• Dual Phone Line Interface

• Option Bus Interface for Built-in Programming

using DCT-P LCD Remote Keypad

• LEDs for Heartbeat, System Trouble and Phone

Line Trouble (one per line)

• Real Time Clock

NOTE: The NIM-2D Upgrade Kit, P/N 500-649576,

must be used.

The MDACT is compatible with the following:

• MMB ROM version 10.14 and higher

• SMB ROM version 6.14 and higher

• CSG-M version 11.05 and higher

• PMI version 4.0 and higher

• Zeus version 4.0 and higher

Installation Instructions

Model MDACT

MXL/FireFinder-XLS Multi-Point Digital Alarm Communicator

P/N 315-099351-6

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

For MXL programming, refer to MXL Operation,

Installation, and Maintenance Manual, P/N 315-

092036, MXL-IQ Operation, Installation, and Mainte-

nance Manual, P/N 315-093624, CSG-M Manual,

P/N 315-090381, and CSG-M Version 11.05 Up-

date, P/N 315-099402, as applicable.

For FireFinder-XLS programming, refer to the

FireFinder-XLS Installation, Operation and Mainte-

nance Manual, P/N 315-033744, and the Zeus

Quick Start Manual, P/N 315-033875.

OPERATION

The MDACT delays the AC Fail trouble signal in

accordance with NFPA and UL requirements. Refer

to the MDACT Programming Manual, P/N 315-

099378 for further information.

INSTALLATION

Remove all system power before installation,

first battery and then AC. (To power up, connect

the AC first, then the battery.)

The MDACT installs into the MXL optional MOM-4/-2

card cage where it occupies one half width slot. The

CABLE P/N 555-190967

TO MMB-2/-3, SMB-2/-3 OR PSR-1

TO MMB-2/-3, SMB-2/-3, PSR-1

24V

OR PSC-12

DO NOT USE

P10

TB6

TB7

345678910111213141516

TB3

MDACT

TB4

INSTALLED IN MXL PANEL

345678910111213141516

DO NOT USE

TB1

TB2

MDACT

MOM-4

NOTE:

MDACT can only be installed

in MOM-4/-2 slots P2 or P4.

Figure 1

MDACT Installation In MXL Panel

Figure 3

NIM-2D Module Board

NIM-2D

SW3

SW1

4321

87654321

INSTALL JUMPER PLUGS

IN ORIENTATION

AS SHOWN.

JP4

INSTALL JUMPER

PLUGS IN ORIENTATION

AS SHOWN. POSITION

SHOWN SELECTED.

JP4

13 15

NOTE: Switch SW3 is factory set.

All switches must remain in

the ON position.

P10

TB6

TB7

MDACT

TB4

INSTALLED IN FIREFINDER-XLS PANEL

345678910111213141516

TB2

XMI

DO NOT USE WITH FIREFINDER-XLS,

SEE XMI INSTALLATION INSTRUCTIONS,

P/N 315-034870

MOM-2*

FOR FIREFINDER-XLS, ONLY

MODEL MOM-2 IS AVAILABLE.

REQUIRES MOUNTING PLATE

MOM2-XMP.

24V

PSC-12

DO NOT USE WITH FIREFINDER-XLS,

SEE XMI INSTALLATION INSTRUCTIONS,

P/N 315-034870

Figure 2

MDACT Installation In FireFinder-XLS Panel

Figure 4

Dialer PCB Layout

Dialer To NIM-2D

Factory Connection

LINE 1

LINE 2

++- -AB

Phone Line 2

Phone Line 1

No Connection

Keypad Molex

Connector Pins

SYS TROUBLE

HEARTBEAT

Phone Line 1 LED

Phone Line 2 LED

System Trouble LED

Heartbeat LED

KEYPAD

No Connection

MDACT can be installed in either slot P2 or slot P4 of

the MOM-4/-2. (See Figure 1.) For FireFinder-XLS,

only the MOM-2 can be used. (See Figure 2.)

Setting the Switches

Set all switches, configuration jumpers, and connec-

tion cables before installing them into the MOM-4/-2.

See Figure 3 for switch locations.

1. Use switch SW1 to set the MXL MNET or

FireFinder-XLS HNET network address. Set this

switch according to the address where the MDACT

is installed in the MXL or FireFinder-XLS network

map. Refer to the CSG-M or Zeus configuration

printout for the address of the module. See Table 1

for MXL (MNET) and XLS (HNET) settings.

2. Switch SW3 is factory set. All switches must

remain in the ON position.

3. Set jumper plugs on JP4 to the "M" position.

4. Set jumper plugs on P6 to the positions shown in

Figure 3.

Telephone Connectons

Telephone Cord Installation

Connect the primary phone line to the MDACT modu-

lar jack "Line1" using a phone cord. Connect the

secondary phone line to the MDACT jack "LINE2"

using another phone cord. See Figure 4 for phone line

connection.

NOTE: You must connect separate primary and

secondary phone lines to the MDACT for all

applications.

Location

To prevent jamming of alarm and other reports, wire

and locate the RJ31X or RJ38X jack so that normal

phone use is temporarily interrupted while the MDACT

transmits data (See Figure 5). After installation,

confirm that the MDACT seizes the line, acquires dial

tone and reports correctly to the receiver.

Figure 5

RJ31X Wiring

NOTE: Use the supplied telco cable assemblies to connect to an RJ31 jack. Make sure the RJ31 jacks are

mounted in a secure location to prevent false disconnections and/or tampering.

Notification

Do not connect registered equipment to party lines or

coin-operated telephones. If the local telephone

company requests notification before you connect the

MDACT to the telephone network, supply the following

information:

• the particular line to which you are connecting the

MDACT

• the make, model and serial number of the device

• the FCC registration number (ESVMUL-46514-AL-E)

and ringer equivalence (0.0B).

If the telephone company makes changes in its

communications facilities, equipment, operations or

procedures that may affect the performance of the

MDACT, the telephone company is obligated to notify

the user in writing.

The MDACT meets the requirements of UL 1950.

RJ31X Module

Full Modular Phone Jack To Dialer

Connecting the Keypad to the MDACT

NOTE: The DCT-P LCD Remote Keypad is used

strictly for programming and debugging

purposesonly.

A DCT-P LCD Remote Keypad can be used to

operate the MDACT Communicator. Plug the molex

connector from the DCT-P onto the connector pins on

the MDACT board as shown in Figure 6.

Use the following steps when programming the

MDACT from the DCT-P.

1. Set the DCT-P address between 1 and 15.

2. Use the wire connector supplied with the DCT-P to

connect the DCT-P to the MDACT. See Figure 6.

3. Program the MDACT as explained in the

programming section of the MDACT Programming

Manual, P/N 315-099378.

NOTE: If there is no keypad activity for three minutes,

the keypad is disabled. The keypad's buzzer

sounds and a "SYSTEM FAULT" message

will appear on the keypad. Disconnect the

keypad from the MDACT by removing the

wire harness plug from the MDACT's keypad

pins, then reconnect the wire plug harness to

re-enable the keypad.

ELECTRICAL RATINGS

Compatibilities

The following receivers and panels have been proven

to be compatible with the MDACT under the method

required by Underwriters Laboratories. Receivers that

are not listed as compatible should not be used with

the MDACT.

DCT-P

Terminal Strip

+12 VDC

RED

BLACK

Com

Data In

GREEN

Data Out

YELLOW

MDACT Fire Communicator

LINE 1

LINE 2

++- -AB 12345 NC C NO

SYS TROUBLE

HEARTBEAT

KEYPAD

Figure 6

Keypad Connection to MDACT Fire Communicator

Available Reporting Formats

•Contact ID (CID): Is the preferred reporting

format. It provides a four digit account code

followed by a three digit event code, a two digit

group number, and a three digit contact number,

all of which are used to provide specific point

identification.

•SIA: Security Industry Association (SIA) Digital

Communication Standard. The DACT provides

level 1 compatibility which includes tonal

acknowledge, basic reports only, and fixed

reporting codes.

tnerruCeludoMCDV5evitcAAm0

tnerruCeludoMCDV42evitcAAm083

tnerruCeludoMCDV42ybdnatSAm023

Compatible Receivers (q= Available)

Report

Format Radionics

D6500 Radionics

D6600 Sur-gard

SG-SLR

Osborne/Hoffman

Quick Alert Model

Ademco

685

Silent

Knight

SK9000

Contact ID qq q q q

SIA300 qq q

SIA110 qq q

Figure 7

MDACT UL Listed Compatibility

TABLE 1

NETWORK ADDRESS PROGRAMMING (SW1)

NETWORK ADDRESS PROGRAMMING

ADDR 87654321 ADDR 87654321 ADDR 87654321 ADDR 87654321

000 ILLEGAL 064 OXOOOOOO 128 XOOOOOOO 192 XXOOOOOO

001 ILLEGAL 065 OXOOOOOX 129 XOOOOOOX 193 XXOOOOOX

002 ILLEGAL 066 OXOOOOXO 130 XOOOOOXO 194 XXOOOOXO

003

004

005

006

007

008

009

010

011

012

013

014

015

016

017

018

019

020

021

022

023

024

025

026

027

028

029

030

031

032

033

034

035

036

037

038

039

040

041

042

043

044

045

046

047

048

049

050

051

052

053

054

055

OOOOOOXX

OOOOOXOO

OOOOOXOX

OOOOOXXO

OOOOOXXX

OOOOXOOO

OOOOXOOX

OOOOXOXO

OOOOXOXX

OOOOXXOO

OOOOXXOX

OOOOXXXO

OOOOXXXX

OOOXOOOO

OOOXOOOX

OOOXOOXO

OOOXOOXX

OOOXOXOO

OOOXOXOX

OOOXOXXO

OOOXOXXX

OOOXXOOO

OOOXXOOX

OOOXXOXO

OOOXXOXX

OOOXXXOO

OOOXXXOX

OOOXXXXO

OOOXXXXX

OOXOOOOO

OOXOOOOX

OOXOOOXO

OOXOOOXX

OOXOOXOO

OOXOOXOX

OOXOOXXO

OOXOOXXX

OOXOXOOO

OOXOXOOX

OOXOXOXO

OOXOXOXX

OOXOXXOO

OOXOXXOX

OOXOXXXO

OOXOXXXX

OOXXOOOO

OOXXOOOX

OOXXOOXO

OOXXOOXX

OOXXOXOO

OOXXOXOX

OOXXOXXO

OOXXOXXX

067

068

069

070

071

072

073

074

075

076

077

078

079

080

081

082

083

084

085

086

087

088

089

090

091

092

093

094

095

096

097

098

099

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

OXOOOOXX

OXOOOXOO

OXOOOXOX

OXOOOXXO

OXOOOXXX

OXOOXOOO

OXOOXOOX

OXOOXOXO

OXOOXOXX

OXOOXXOO

OXOOXXOX

OXOOXXXO

OXOOXXXX

OXOXOOOO

OXOXOOOX

OXOXOOXO

OXOXOOXX

OXOXOXOO

OXOXOXOX

OXOXOXXO

OXOXOXXX

OXOXXOOO

OXOXXOOX

OXOXXOXO

OXOXXOXX

OXOXXXOO

OXOXXXOX

OXOXXXXO

OXOXXXXX

OXXOOOOO

OXXOOOOX

OXXOOOXO

OXXOOOXX

OXXOOXOO

OXXOOXOX

OXXOOXXO

OXXOOXXX

OXXOXOOO

OXXOXOOX

OXXOXOXO

OXXOXOXX

OXXOXXOO

OXXOXXOX

OXXOXXXO

OXXOXXXX

OXXXOOOO

OXXXOOOX

OXXXOOXO

OXXXOOXX

OXXXOXOO

OXXXOXOX

OXXXOXXO

OXXXOXXX

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

XOOOOOXX

XOOOOXOO

XOOOOXOX

XOOOOXXO

XOOOOXXX

XOOOXOOO

XOOOXOOX

XOOOXOXO

XOOOXOXX

XOOOXXOO

XOOOXXOX

XOOOXXXO

XOOOXXXX

XOOXOOOO

XOOXOOOX

XOOXOOXO

XOOXOOXX

XOOXOXOO

XOOXOXOX

XOOXOXXO

XOOXOXXX

XOOXXOOO

XOOXXOOX

XOOXXOXO

XOOXXOXX

XOOXXXOO

XOOXXXOX

XOOXXXXO

XOOXXXXX

XOXOOOOO

XOXOOOOX

XOXOOOXO

XOXOOOXX

XOXOOXOO

XOXOOXOX

XOXOOXXO

XOXOOXXX

XOXOXOOO

XOXOXOOX

XOXOXOXO

XOXOXOXX

XOXOXXOO

XOXOXXOX

XOXOXXXO

XOXOXXXX

XOXXOOOO

XOXXOOOX

XOXXOOXO

XOXXOOXX

XOXXOXOO

XOXXOXOX

XOXXOXXO

XOXXOXXX

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

XXOOOOXX

XXOOOXOO

XXOOOXOX

XXOOOXXO

XXOOOXXX

XXOOXOOO

XXOOXOOX

XXOOXOXO

XXOOXOXX

XXOOXXOO

XXOOXXOX

XXOOXXXO

XXOOXXXX

XXOXOOOO

XXOXOOOX

XXOXOOXO

XXOXOOXX

XXOXOXOO

XXOXOXOX

XXOXOXXO

XXOXOXXX

XXOXXOOO

XXOXXOOX

XXOXXOXO

XXOXXOXX

XXOXXXOO

XXOXXXOX

XXOXXXXO

XXOXXXXX

XXXOOOOO

XXXOOOOX

XXXOOOXO

XXXOOOXX

XXXOOXOO

XXXOOXOX

XXXOOXXO

XXXOOXXX

XXXOXOOO

XXXOXOOX

XXXOXOXO

XXXOXOXX

XXXOXXOO

XXXOXXOX

XXXOXXXO

XXXOXXXX

XXXXOOOO

XXXXOOOX

XXXXOOXO

XXXXOOXX

XXXXOXOO

XXXXOXOX

XXXXOXXO

XXXXOXXX

056 OOXXX OOO 120 OXXXXOOO 184 XOXXXOOO 248 ILLEGAL

057 OOXXXOOX 121 OXXXXOOX 185 XOXXXOOX 249 ILLEGAL

058 OOXXXOXO 122 OXXXXOXO 186 XOXXXOXO 250 ILLEGAL

059 OOXXXOXX 123 OXXXXOXX 187 XOXXXOXX 251 ILLEGAL

060 OOXXXXOO 124 OXXXXXOO 188 XOXXXXOO 252 ILLEGAL

061 OOXXXXOX 125 OXXXXXOX 189 XOXXXXOX 253 ILLEGAL

062 OOXXXXXO 126 OXXXXXXO 190 XOXXXXXO 254 ILLEGAL

063 OOXXXXXX 127 OXXXXXXX 191 XOXXXXXX 255 ILLEGAL

O = OPEN (or OFF) X = CLOSED ( or ON

)

P/N 315-099351-6

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

Inhaltsverzeichnis

Andere Siemens Handy Handbücher

Siemens

Siemens Gigaset M56 Bedienungsanleitung

Siemens

Siemens S55 Bedienungsanleitung

Siemens

Siemens SL65 Bedienungsanleitung

Siemens

Siemens Gigaset S45 Bedienungsanleitung

Siemens

Siemens Gigaset SL75 WLAN Bedienungsanleitung

Siemens

Siemens A75 Bedienungsanleitung

Siemens

Siemens CF75 Bedienungsanleitung

Siemens

Siemens SFG75 Bedienungsanleitung

Siemens

Siemens PEGASUS-DTC AX72 Bedienungsanleitung

Siemens

Siemens A50 Bedienungsanleitung

Siemens

Siemens S65 Einrichtungshandbuch

Siemens

Siemens MC60 Bedienungsanleitung

Siemens

Siemens SL65 Bedienungsanleitung

Siemens

Siemens Gigaset S45 Bedienungsanleitung

Siemens

Siemens SL45i Bedienungsanleitung

Siemens

Siemens A31 Bedienungsanleitung

Siemens

Siemens C61 Bedienungsanleitung

Siemens

Siemens ST55 Bedienungsanleitung

Siemens

Siemens E71 Bedienungsanleitung

Siemens

Siemens AX75 Bedienungsanleitung

Siemens

Siemens CL75 Bedienungsanleitung

Siemens

Siemens De inspired C56 Bedienungsanleitung

Siemens

Siemens Xelibri X6 Bedienungsanleitung

Siemens

Siemens C65 Bedienungsanleitung

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LG LM-X420QN Bedienungsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

LG LM-K420EMW Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung