Siemens SIMATIC TP700 Comfort Outdoor Bedienungsanleitung

FOOD

CONSUMER

MEDICAL

PLASTIC

INDUSTRIAL

RUBBER

MASTIC

AUTOMOTIVE

Original Operating Instructions

Siemens TP700 Comfort

Touch-sreen operator control panel

Gillard Cutting Technology

Alexandra Way, Ashchurch Business Centre, Tewkesbury, GL20 8NB, England

Tel: +44 (0) 1684 290 243

Email: sales@gillardcutting.com

For more technical support, please go to our website:

www.gillardcutting.com/technical

Operating Instructions

Siemens TP700 Comfort

Touch-sreen operator control panel

Warning!

Ensure that all personnel involved in the operation and maintenance of any machine,

as well as those persons who will act as supervisory personnel for the machines, have

read and understood fully these instructions and those contained in the accompanying

supplier’s instruction manuals and instruction sheets, before attempting to operate or

perform maintenance on this machine.

Should any questions arise regarding the safe and proper operation or maintenance of

this machine, contact the manufacturer at the address listed below before proceeding.

Peter Gillard & Co. Limited

Alexandra Way

Ashchurch Business Centre

Tewkesbury

Gloucestershire

England

GL20 8NB

Tel: +44 1684 290243

Email: tech@gillardcutting.com

www.gillardcutting.com

For more technical support, please go to our website:

www.gillardcutting.com/technical 1

For more technical support, please go to our website:

www.gillardcutting.com/technical 2

Siemens TP700 Comfort

Touch-screen operator control panel.

This guide gives details of all buttons/elds/functions that are available within

the standard machine software. Some functions will only appear under certain

conditions and/or are optional. Please check the full specication of machine

supplied.

1. INITIALISATION.

The screen below is displayed at power up. The start button is displayed once all

parameters have been loaded.

For more technical support, please go to our website:

www.gillardcutting.com/technical 3

2. MACHINE SAFETY

The machine is tted with 3 safety functions.

• MainMachineDoor

• CutterSafetyFunction

• EmergencyStops

All of the safety functions are motored by the Siemens S7-1214FC Safety PLC. This

handles most of the machines logic and safety functions.

By pressing the Emergency Stop or opening the main machine door, will bring the

machine to a controlled stop and remove all torque and energy from motors and

actuators.

The following screens will appear if the Emergency Stop safety function is called

upon.

Once released and the circuit is complete, it can be reset by pressing the blue safety

circuit reset button, causing the screen to return to the main control screen.

Opening the main door of the machine will act in the same way as pressing the

Emergency Stop.

The Emergency Stop will always display if called upon, even if other safety functions

are active at the same time.

If the main door is opened, the following screen will be displayed instead:

For more technical support, please go to our website:

www.gillardcutting.com/technical 4

When all guarding, doors and Emergency Stop have been closed the following reset

screen will appear. This indicates the safety functions are ready to be reset with the blue

reset button ashing. Check it is safe to do so and press the blue button for ½ second.

When the machine has successfully reset, you will be returned to the home screen.

For more technical support, please go to our website:

www.gillardcutting.com/technical 5

2.1.1 Cutter Safety

The cutter has its own independent safety function that will allow sliding away the

cutter block and still be able to drawing product through the machine with the belts.

When any part of the cutter safety function is activated, the pop-up below, left will be

displayed on the home screen. This will indicate the safety circuit is not complete.

When the safety circuit is complete, the pop-up below, right will be displayed, again

the blue rest button will ash.

Simply press the blue button to reset the safety function and allow the cycle to

continue.

The button is designed to be pressed for approximately ½ second before resetting.

The Cutter Safety pop-up is located on the home screen:

For more technical support, please go to our website:

www.gillardcutting.com/technical 6

3. MACHINE FAULT

The screen below will be displayed if there is a serious system fault. This could be

internal communications or a safety related function. Hopefully this should never

appear.

The rst port or call is to check all of the safety sensors and emergency stops. The

monitoring of the safety circuits is very accurate and any discrepancy in the reading

of both channels

Pressing the yellow warning symbol will load the system diagnostic screen. Gillard

will need the information contain within to help you with your fault.

If you see this screen, please contact Gillard: tech@gillardcutting.com or call 01684

851989

For more technical support, please go to our website:

www.gillardcutting.com/technical 7

4. HOME SCREEN

This is the normal operator screen. All day to day cutting changes can be controlled

from this screen.

The screen is divided in three different parts: Caterpillar, Cutter and Batch. Each

area has its own panel where it is possible to select different settings. To open the

different panels, press on the green bottom bar.

4.1.1 Caterpillar

Start/Stop Caterpillar (Button):

To start conveyor belts, press the green button to start the transport belts. As an

indication the button will turn red plus graphic within the symbol will begin to rotate

to indicate movement.

For more technical support, please go to our website:

www.gillardcutting.com/technical 8

Caterpillar belt speed (Blue Display):

Adjusts individually the transport belt speeds calibrated in 0.1 meters per minute.

Lightly tap the screen within the adjustment area to display input panel and adjust

parameter. Press return key to enter the new value.

Caterpillar belt speed (White Display):

Displaytheactualspeedofthecaterpillar.

4.1.2 Cutter

Start/Stop Cut Cycle (Left Button):

To start Cutter cycle, press the green button and it will start the knife motor. Cutting

mode is dependent on cut mode switch, see above. As an indication the button will

turn red plus the knife graphic within the symbol will rotate to indicate movement.

Manual Cut Button (Right Button):

When pressed completes one manual cut. Note only operates when machine is out

of cutting cycle.

Mode parameters pre-set (Blue Display):

Adjusts the length, speed or time. Lightly tap adjustment to display input panel and

enter desired value. Press return key to enter the new value.

Actual mode parameter display (White Display):

Displaystheactuallengthorspeed.

4.1.3 Batch

Batch size (Blue Display):

Numberofunitsperbatch.Maximumvalue999,999units.Ifabatchcompleted

beacon is tted on the machine it goes off when the performed cuts number is

equal to the batch size specied.

Performed cuts (White Display):

Numberofcutsperformedbythemachine.Doubleclickonthedisplaytoresetthis

value. If this number reaches the batch size it will be reset automatically.

For more technical support, please go to our website:

www.gillardcutting.com/technical 9

4.1.4 Caterpillar panel

Click on the caterpillar green button to open and close the panel. In this panel is

possible to select all the settings to control the caterpillar.

LOCAL MODE

SpeedissetfromtheHMI.Thisisenteredinmetresperminute.

Caterpillar belt speed (Blue Display):

Adjusts individually the transport belt speeds calibrated in 0.1 meters per minute.

Lightly tap the screen within the adjustment area to display input panel and adjust

parameter. Press return key to enter the new value.

Caterpillar belt speed (White Display):

Displaystheactualspeedofthecaterpillar.

Andere Handbücher für SIMATIC TP700 Comfort Outdoor

Inhaltsverzeichnis

Andere Siemens Bedienfeld Handbücher

Siemens

Siemens Synco RMZ792 Bedienungsanleitung

Siemens

Siemens SIMATIC Mobile Panel 277F IWLAN V2 Bedienungsanleitung

Siemens

Siemens SIMATIC HMI TP900 Bedienungsanleitung

Siemens

Siemens FireSeeker FS-250 Betriebsanleitung

Siemens

Siemens SINUMERIK 840D sl Technisches Dokument

Siemens

Siemens SIMATIC HMI KP400 Comfort Bedienungsanleitung

Siemens

Siemens QAA70 Bedienungsanleitung

Siemens

Siemens FC121-ZA Bedienungsanleitung

Siemens

Siemens SINUMERIK ONE MCP 2400 Technisches Dokument

Siemens

Siemens SINAMICS IOP-2 Bedienungsanleitung

Siemens

Siemens SPC 4300 Bedienungsanleitung

Siemens

Siemens SIMATIC Mobile Client900RFN Bedienungsanleitung

Siemens

Siemens FC361-ZZ Bedienungsanleitung

Siemens

Siemens FC361-ZZ Bedienungsanleitung

Siemens

Siemens Apogee P1 Bedienungsanleitung

Siemens

Siemens SPC5000 Merkblatt

Siemens

Siemens GENESIS II Bedienungsanleitung

Siemens

Siemens IVK-6 Bedienungsanleitung

Siemens

Siemens SINAMICS IOP Bedienungsanleitung

Siemens

Siemens SIMATIC TD 200 Bedienungsanleitung

Siemens

Siemens SINAMICS S120 Bedienungsanleitung

Siemens

Siemens OP1S Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl OP 010 Bedienungsanleitung

Siemens

Siemens FC123-ZA Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten