Siemens CZM-1B6 Service-Handbuch
P/N 315-095355-9
OPERATION
The Model CZM-1B6 from Siemens Industry, Inc.,
is an MXL intelligent device that connects a single
zone of conventional devices to an analog loop.
The CZM-1B6 can power up to fifteen compatible
2-wire, ionization or photoelectric smoke detectors.
It can also monitor an unlimited number of shorting
devices such as waterflow switches, thermal
detectors, manual stations, etc.
Each CZM-1B6 can be assigned a 32 character
custom alphanumeric message. A multicolor LED,
visable through the cover plate, indicates the
condition of the circuit. This multicolor LED displays
red for alarm, yellow for trouble, and green for
normal operation (See Figure 1).
The CZM-1B6 supports Class A and Class B
wiring. The module uses one address on the
analog circuit. It does not require any mechanical
address programming. Use Model DPU Device
Programming Unit or FPI-32 Programmer/Tester to
program and test the module.
For additional information on the MXL/MXLV System,
refer to the MXL/MXLV Manual, P/N 315-092036.
SETTING THE MODULE ADDRESS
1. Using the DPU Device Programming Unit or
FPI-32 Programmer/Tester, plug the
programming cable into the programming
receptacle on the CZM-1B6 (See Figure 1).
2. Set the System address for the CZM-1B6 by
following the instructions in the FPI-32 Programmer/
Tester Manual, P/N 315-090077, or the DPU
User's Manual, P/N 315-033260, as appropriate.
NOTE: With FPI-32 Rev. 1.3 software, only 1=MXL
mode should be used when programming a
device.
INSTALLATION
Remove all system power before installation, first
battery and then AC. (To power up, first connect the
AC and then the battery.)
Electrical Connections
After you have set the CZM-1B6 address, connect the
field wiring.
There are three basic connections
to the
CZM-1B6. All terminals are power limited.
1. Initiating Devices (Figures 2, 3, and 4)
The CZM-1B6 supports one zone of initiating devices
in either Class A or Class B. The initiating devices are
connected to terminals 5–8 on the CZM-1B6 terminal
block. Figure 2 shows the Class A wiring. Figure 3
shows the Class B wiring.
Figure 4 shows the wiring for the PBA-1191 beam
detector. When the PBA-1191 is used, the 2-position
plug from jumper J1 must be removed. Follow the
steps listed below:
a. Remove the screw from the center of the
CZM-1B6 plastic cover and place it to one side.
b. Remove the circuit board and locate jumper J1.
c. Remove the 2-position plug from J1.
Installation Instructions
Model CZM-1B6
Remote Conventional Zone Module
Figure 1
Model CZM-1B6
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada
2
d. Reassemble the circuit board and plastic cover
using the screw that was removed in the first
step.
e. Be sure to use the correct end of line device with
the CZM-1B6 in this configuration.
The devices in the tables at the right are listed for use
with the CZM-1B6. Use up to fifteen detectors, any
combination of those listed. Only one PB-1191 or one
DF-1192, and no additional devices, can be connected
to a CZM-1B6. Detector operated accessories cannot
be used with the CZM-1B6. The model numbers listed
are the UL compatibility identifiers.
May use up to 15 detectors of any type.
* Only one PBA-1191 or one DF-1192, and no additional
devices, can be connected to a CZM-1B6.
Figure 2
CZM-1B6 Wiring Diagram (Initiating Devices)
Class A (Style D) Installation
Figure 3
CZM-1B6 Wiring Diagram (Initiating Devices)
Class B (Style B) Installation
Figure 4
CZM-1B6 Wiring Diagram
PB-1191 Installation
123456 7 8 9
+
-
-
+
+
-
-
+
+
-
-
+
EARTH
ANALOG LOOP
POWER
WIRE MINIMUM 18 AWG, 35 ohms MAX
SUPERVISED, POWER
LIMITED PER NEC 760
VOLTAGE 24V UNFILTERED FULL WAVE
STYLE D
(CLASS A)
EOL *
* EOL DEVICE IS 4.7K
,
1/4W
(
P/N 140-820188
)
+
-- --
+++
123456 7 8 9
+
-
-
+
+
-
-
+
+
-
-
+
EARTH
ANALOG LOOP
POWER
WIRE MINIMUM 18 AWG, 35 ohms MAX
SUPERVISED, POWER
LIMITED PER NEC 760
VOLTAGE 24V UNFILTERED FULL WAVE
STYLE B
(CLASS B)
*EOL DEVICE IS 4.7K,
1/4W (P/N 140-820188)
+
-- --
+++
EOL*
)ylnOdevorppAMF(efaSyllacisnirtnI
rotceteDesaB snoitcurtsnInoitallatsnI rebmuNtraP
1-ISIhtiwSI3-IDS3-BD81-34
9180-513
NOTE:
Positive and negative ground fault detected at
<30K ohms for terminals 5-8 on CZM-1B6.
6B1-MZCrofytilibitapmoC
rotceteDesaB
noitallatsnI
snoitcurtsnI
rebmuNtraP
H3/3-IDS3-BD349180-513
H3A/3A-IDS3-BD3
49180-513
H3B/3B-IDI3-DA432390-513
*531-P3-TDS3-BD545710-513
11-TD11-BD
TPDA-BDhtiwS3-BD
924590-513
924590-513
19
11-ABP1911-BBP424590-513
3-EPS3-BD
PLI3-DA
578090-513
432390-513
T11/11-EP11-BD
TPDA-BDhtiwS3-BD
P11-DA
891490-513
891490-513
956590-513
3
2. Analog Loops (See Figure 5)
The CZM-1B6 communicates with the MXL via its
analog addressable loops. These loops may be on the
MMB or on the optional ALD-2I module. The analog
loops may be wired Class A or Class B. Figure 5
shows both wiring types, as well as the connections to
either the MMB or the MOM-4 when the ALD-2I
module is used.
3. 24 VDC Power (See Figure 6)
The CZM-1B6 receives its power from the CZM-1B6
power output on the MMB. This power is available on
TB5 of the MMB at terminals 9–12 or TB3 on the
PSR-1 on terminals 3-6. The power may be wired as
Class A or Class B. Since the CZM-1B6 monitors the
power at its screw terminals, you can star or T-tap the
power connection in the Class B configuration only.
Refer to Figure 6 for the wiring diagram.
Figure 5
CZM-1B6 Wiring Diagram (Analog Loop)
Figure 6
CZM-1B6 Wiring Diagram (Power)
For loop resistance, refer to
PSR-1 Installation Instructions, P/N 315-090911,
MMB-1 Installation Instructions, P/N 315-090375,
MMB-2 Installation Instructions, P/N 315-095097, or
MMB-3 Installation Instructions, P/N 315-048860
as applicable.
48 8
37 7
26 6
15 5
55
48 8
37 7
26 6
1
444
333
222
111
444
333
222
111
MOM-4
TB2
MOM-4
TB1
LOOP
1
LOOP
1
LOOP
1
LOOP
2
LOOP
2
LOOP
2
MMB
TB2
MMB
TB3
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
3
3
4
4
4
4
4
4
4
5
5
5
5
5
5
5
6
6
6
6
6
6
6
7
7
7
7
7
7
7
8
8
8
8
8
8
8
CZM-1/1B6
CZM-1/1B6
CZM-1/1B6
CZM-1/1B6
CZM-1/1B6
CZM-1/1B6
CZM-1/1B6
+
+
+
-
-
-
ALD-2I
CLASS A INSTALLATION*
CLASS B INSTALLATION**
*OPERATES IN FULL COMFORMANCE WITH STYLE 6
NO T-TAPPING ALLOWED
LOOP RESISTANCE 100 Ohms MAX.
ALL WIRE MINIMUM 18 AWG
NO EOL DEVICE REQUIRED
SUPERVISED, POWER LIMITED PER NEC 760
T-TAPPING ALLOWED
**OPERATES IN FULL COMFORMANCE WITH STYLE 4
***
***
***JUMPERS CAN BE REMOVED FROM MMB-3
WITH CSGM CONFIGURATION
312
411
510
69
312
411
510
69
MMB
TB5
PSR-1
TB3
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
9
9
9
9
9
9
9
9
CZM-1B6
CZM-1B6
CZM-1B6
CZM-1B6
CZM-1B6
CZM-1B6
CZM-1B6
CZM-1B6
+
+
+
-
-
-
CLASS A INSTALLATION
NO T-TAPPING ALLOWED
CLASS B INSTALLATION
T-TAPPING ALLOWED
ALL WIRE MINIMUM 18 AWG
NO EOL DEVICE REQUIRED
SUPERVISED, POWER LIMITED PER NEC 760
*
*
*JUMPERS CAN BE REMOVED FROM MMB-3
WITH CSGM CONFIGURATION
NOTE:
Positive and negative ground fault detected at <30K ohms
for terminals 5-8 on CZM-1B6.
NOTE:
Positive and negative ground fault detected at
<30K ohms for terminals 5-8 on CZM-1B6.
P/N 315-095355-9
Figure 7
Wiring Diagram of Intrinsically Safe Zone
NOTES:
1. Intrinsically Safe Output:
Open Circuit Voltage: 28 VDC
Short Circuit Current: 93mA
2. Maximum loop resistance must not exceed 35 ohms.
3. A maximum of ten DI-3IS Ionization Detectors or up to five
S121 or S122 Flame Detectors can be used in addition to
mechanical (non-energy storing) shorting devices.
4. Maximum safe system voltage is 250 VAC.
5. For mounting and installation of the ISI-1, see the ISI-1
instructions.
6. Only mechanical (non-energy storing) shorting devices
such as the MS-51 Manual Station may be used.
7. WARNING: Do not make any connection to terminal 6
of the DB-3S base. Such a connection would void use
in an intrinsically safe application.
8. In addition, S121 and S122 are also approved for use
in Class II and Class III, Groups E, F, and G.
9. For guidance on installation see ANSI/ISA RP 12.6,
“Installation of Instrinsically Safe Instrument Systems in
Class I Hazardous Locations”.
10. For DI-3IS information, see the DI-3 Series installation
instructions, P/N 315-081943.
11. For S121 and S122 information, see the installation
instructions, P/N 315-085258.
INTRINSICALLY SAFE APPLICATION
FM APPROVED ONLY
7
8
9
10
11
12
6
5
4
3
2
1
7
9
10
11
12
6
4
3
2
1
85
ISI-1*
*THE ISI-1 IS A TWO-CHANNEL INTERFACE.
ONE CHANNEL IS SHOWN CONNECTED.
ISI-1*
Mechanical Installation
1. Mount the CZM-1B6 in a standard two gang
electrical box. The box must have a depth of at
least 3½ inches.
2. When the field wiring is connected (See above),
press the CZM-1B6 into the box and fasten it with
the four screws provided.
3. Attach a dress bezel if necessary, making sure
that the ALARM LED is aligned with the hole in the
bezel.
Electrical Ratings
tnerruCeludoMCDV5evitcAAm0
tnerruCeludoMCDV42evitcAAm05
tnerruCeludoMCDV42ybdnatSAm5.21
Zone resistance: 35 ohms total
SAERA1-ISI
LENNAHCEFASSUODRAZAH
+19 5
-18 4
+2212
-2111
01,7,6,3:NOITCENNOCON
Andere Siemens Steuereinheit Handbücher
Siemens
Siemens VVG44.15-0.4S Betriebsanleitung
Siemens
Siemens SINAMICS G130 Datenblatt
Siemens
Siemens PXC-16 Compact Produkthandbuch
Siemens
Siemens FDK:085U0321 Bedienungsanleitung
Siemens
Siemens WFZ43 Bedienungsanleitung
Siemens
Siemens SIRIUS 3RU Series Bedienungsanleitung
Siemens
Siemens SINUMERIK 840D sl Betriebsanleitung
Siemens
Siemens RUGGEDCOM ROS Bedienungsanleitung
Siemens
Siemens SIRIUS 3SB38 Bedienungsanleitung
Siemens
Siemens ACVATIX VPF43 Series Bedienungsanleitung
Siemens
Siemens V-2030 Bedienungsanleitung
Siemens
Siemens 550-818B Bedienungsanleitung
Siemens
Siemens SINAMICS S110 Bedienungsanleitung
Siemens
Siemens simatic ET 200MP Bedienungsanleitung
Siemens
Siemens SITOP PSE200U 3 A Bedienungsanleitung
Siemens
Siemens SINUMERIK 840D sl Merkblatt
Siemens
Siemens 4AI RTD Bedienungsanleitung
Siemens
Siemens SIPROTEC 7SJ80 Bedienungsanleitung
Siemens
Siemens MC35 Terminal Bedienungsanleitung
Siemens
Siemens SIMATIC FM 351 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
