Siemens SINAMICS S110 Bedienungsanleitung

Getting Started

SINAMICS

Getting Started · 10/2008

SINAMICS S110

_____________

Preface

Drive concept

Requirements

Creating the drive project

ONLINE

Getting Started

Function Manual

10/2008

6SL3097-4AG10-0BP0

vailable from

Firmware-Version 4.1

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE

indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Commissioning and

operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes

in this documentation qualified persons are defined as persons who are authorized to commission, ground and

label devices, systems and circuits in accordance with established safety practices and standards.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be adhered to. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

Ordernumber: 6SL3097-4AG10-0BP0

Ⓟ 11/2008

Technical data subject to change

Getting Started

Function Manual, 10/2008, 6SL3097-4AG10-0BP0 5

Preface

SINAMICS documentation

The SINAMICS documentation is organized in two parts:

● General documentation/Catalogs

● Manufacturer/service documentation

At http://www.siemens.com/motioncontrol/docu information is available on the following

topics:

● Ordering documentation:

Here you will find the current overview of publications.

● Downloading documentation:

Links to more information for downloading files from Service & Support.

● Researching documentation online.

Information on DOCconCD and direct access to the publications in DOCconWeb.

● Individually compiling documentation on the basis of Siemens contents with the My

Documentation Manager (MDM), refer to http://www.siemens.com/mdm.

● The My Documentation Manager offers you a number of features for compiling your own

machine documentation.

Training and FAQs

Information on the range of training courses and FAQs (frequently asked questions) are

available via the page navigation.

Purpose of the document

This documentation is aimed at beginners who want to find out more about the

SINAMICS S110 drive system. This document will show you how to configure an S110 drive

train within approx. 3 minutes and start the motor.

Internet address for SINAMICS

http://www.siemens.com/sinamics.

EC Declaration of Conformity

The EC Declaration of Conformity for the EMC Directive can be found at:

● On the Internet:

http://support.automation.siemens.com

In the "Search" field, enter the document ID 15257461 and press "Enter".

● At the relevant Siemens office of the I DT MC Business Unit of Siemens AG.

Preface

Getting Started

6 Function Manual, 10/2008, 6SL3097-4AG10-0BP0

Safety notices

DANGER

•Commissioning must not start until you have ensured that the machine in which the

components described here are to be installed complies with Directive 98/37/EC.

•SINAMICS devices and AC motors may only be commissioned by suitably qualified

personnel.

•The personnel must take into account the information provided in the technical customer

documentation for the product, and be familiar with and observe the specified danger

and warning notices.

•When electrical equipment and motors are operated, the electrical circuits automatically

conduct a dangerous voltage.

•Dangerous mechanical movements are possible during system operations.

•All the work carried-out on the electrical machine or system must be carried-out with it in

a no-voltage condition.

•SINAMICS devices with AC motors may only be connected to the power supply via an

AC-DC residual-current-operated device with selective switching once verification has

been provided that the SINAMICS device is compatible with the residual-current-

operated device in accordance with EN 50178, Chapter 5.2.11.2.

WARNING

•The successful and safe operation of this equipment and motors is dependent on

professional transport, storage, installation and mounting as well as careful operations ,

service and maintenance.

•Information and data from the catalogs and quotations also apply to special versions of

the equipment and motors.

•In addition to the danger and warning information provided in the technical customer

documentation, the applicable national, local, and plant-specific regulations and

requirements must be taken into account.

•Only protective extra-low voltages (PELV) that comply with EN60204-1 may be

connected to all connections and terminals between 0 and 48 V.

CAUTION

•The motors can have surface temperatures of over +80 °C.

•This is why temperature-sensitive components, e.g. cables or electronic components

must not be in contact with or attached to the motor.

•When connecting up cables, please ensure that they

– are not damaged

– are not subject to tensile stress

– cannot be touched by rotating components.

Preface

Getting Started

Function Manual, 10/2008, 6SL3097-4AG10-0BP0 7

CAUTION

•As part of routine tests, SINAMICS devices with AC motors undergo a voltage test in

accordance with EN 50178. Before the voltage test is performed on the electrical

equipment of industrial machines to EN 60204-1, Section 19.4, all connectors of

SINAMICS equipment must be disconnected/unplugged to prevent the equipment from

being damaged.

•Motors should be connected up according to the circuit diagram provided otherwise they

may be destroyed.

Note

When operated in dry operating areas, SINAMICS equipment with AC motors conforms to

low-voltage Directive 73/23/EEC.

CAUTION

Electrostatic sensitive devices (ESD) are single components, integrated circuits or devices

that can be damaged by electrostatic fields or electrostatic discharges.

Regulations for the ESD handling:

During the handling of electronic components, pay attention to the grounding of the person,

workplace and packaging!

Electronic components may be touched by persons only when

•these persons are grounded using an ESD bracelet, or

•these persons in ESD areas with a conducting floor wear ESD shoes or ESD grounding

straps.

Electronic components should be touched only when this is unavoidable. The touching is

permitted only on the front panel or on the circuit board edge.

Electronic components must not be brought into contact with plastics or clothing made of

artificial fibers.

Electronic components may only be placed on conducting surfaces (table with ESD coating,

conducting ESD foamed material, ESD packing bag, ESD transport container).

Electronic components may not be placed near display units, monitors or televisions

(minimum distance from the screen > 10 cm).

Measurements must only be taken on boards when the measuring instrument is grounded

(via protective conductors, for example) or the measuring probe is briefly discharged before

measurements are taken with an isolated measuring device (for example, touching a bare

metal housing).

Getting Started

Function Manual, 10/2008, 6SL3097-4AG10-0BP0 9

Contents

Preface ...................................................................................................................................................... 5

1 Drive concept........................................................................................................................................... 11

1.1 Overview ......................................................................................................................................11

1.2 Components.................................................................................................................................11

2 Requirements .......................................................................................................................................... 13

2.1 Hardware and software components ...........................................................................................13

3 Creating the drive project ONLINE .......................................................................................................... 15

3.1 Creating the drive project ONLINE ..............................................................................................15

3.2 Requirements...............................................................................................................................15

3.3 Creating projects ONLINE ...........................................................................................................16

3.4 Transferring the configuration......................................................................................................20

3.5 Operating the drive with the control panel ...................................................................................23

Andere Handbücher für SINAMICS S110

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens ASIC SIM 1-2 Stücklistenhandbuch

Siemens

Siemens MICROMASTER 420 Bedienungsanleitung

Siemens

Siemens RMH760B Bedienungsanleitung

Siemens

Siemens SINUMERIK 840Di sl Kurzanleitung

Siemens

Siemens SIMATIC ET 200SP TM ECC 2xPWM ST Bedienungsanleitung

Siemens

Siemens SINAMICS Series Technisches Dokument

Siemens

Siemens SIPLUS ECC8000 Bedienungsanleitung

Siemens

Siemens ACVATIX VPF53 Series Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP CM 1xDALI Betriebsanleitung

Siemens

Siemens IM 155-6 PN ST Technisches Dokument

Siemens

Siemens SIMATIC S5 Bedienungsanleitung

Siemens

Siemens CLS-1000 Gebrauchsanweisung

Siemens

Siemens LMV 5 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 808D Bedienungsanleitung

Siemens

Siemens SED2-LONI/F Bedienungsanleitung

Siemens

Siemens SIMATIC NET RX1500 Bedienungsanleitung

Siemens

Siemens SiPass Driver Bedienungsanleitung

Siemens

Siemens Simatic Net Scalance M812 Bedienungsanleitung

Siemens

Siemens 3VA9.37-0VF10 Bedienungsanleitung

Siemens

Siemens SINAMICS G120D Bedienungsanleitung

Siemens

Siemens SINAMICS V20 Inverter Bedienungsanleitung

Siemens

Siemens SIMATIC FM 351 Bedienungsanleitung

Siemens

Siemens XLD-1 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Stücklistenhandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung