Siemens FCA2018-U1 Bedienungsanleitung

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

A6V10315044_enUS_c

INTRODUCTION The Model FCA2018-U1 from Siemens

Industry, Inc., is an Universal Fire

Protocol module that interfaces to a

Centronics parallel printer. It must be

located where access to the FS20

System UFP network and 24VDC power

limited output are available.

The FCA2018-U1 is required whenever a

logging printer is needed. It translates

the UFP messages into a standard Centronics printer interface. When used

in conjunction with the PAL-1, it provides a supervised logging printer meeting the

requirements of NFPA 72 Proprietary or UL 1076 Security systems. For NFPA 72

Local, Auxiliary or Remote Station applications any UL EDP listed Centronics parallel

printer may be used (See notes 2, 3, and 4 on Figure 3).

Features FCA2018-U1 features are as follows:

• Supervision of the PAL-1 includes paper out, paper jam, printer off line,

printer power off and printer disconnected.

• Can be connected to the UFP Style 4 or Style 6.

• Includes diagnostic LEDs to indicate failure of the UFP or the CPU. It also

has a power on indicator.

• Includes a reset switch in the event that the FCA2018-U1 requires a

hardware reset.

• Can be mounted on any smooth surface within 6 feet of the PAL-1.

Figure 1

FCA2018-U1 Remote Peripheral Module

Remote Peripheral Module

Installation Instructions

Model FCA2018-U1

Siemens Industry, Inc.

Building Technologies Division

A6V10315044_enUS_c2

OPERATION When a system event occurs, the Operating Unit sends a print message to the

FCA2018-U1 via UFP.The FCA2018-U1 is responsible for printing the message.The

FCA2018-U1 contains a buffer to ensure that events that occur at a rate faster than the

PAL-1 can print them are not lost.

The FCA2018-U1 continu-

ously monitors the

connection to the PAL-1

checking for any errors

that would inhibit printing.

Any errors that are

detected are communi-

cated to the Operating

Unit via UFP for annuncia-

tion. Restoration to the

normal condition is also

detected and communi-

cated to the Operating

Unit. Print messages that

arrive at the FCA2018-U1

during a printer fault are

stored in the buffer.

Controls and Indicators The UFP side panel of the

FCA2018-U1 contains one

reset switch, three LEDs,

one termination switch and

one UFP address switch as

shown in Figure 2.

A reset switch is located

on the top of the panel.

Pushing the reset switch

re-initializes the FCA2018-

U1 operation.

POWER (Green) Normally ON. When illuminated, indi-

cates that power for the FCA2018-U1 is

applied to the module.

CPU FAIL (Yellow) Normally OFF. When illuminated, indi-

cates that the module microprocessor

has failed.

UFP FAIL (Yellow) Normally OFF. When illuminated, indi-

cates that the UFP communication with

the FCA2018-U1 has terminated.

A three-position switch located directly beneath the LEDs on the UFP side of the

FCA2018-U1 is used to set the UFP network address of the FCA2018-U1.

PORT 3

SPP

PORT 1

RS-232

10 7

RXD

TXD

GND

RTS

CTS

RXD

TXD

GND

RTS

CTS

RCV+

RCV-

XMIT+

XMIT-

GND

PORT 2

RS-232

PORT 2

RS-485

PORT 2

SELECT

PRINTER SIDE

3CHASSIS GND

24V INPUT

HNET/UFP

ADDRESS

TERMINATION

RESET

POWER

CPU FAIL

HNET FAIL

UFP SIDE

Figure 2

FCA2018-U1 Side Panel Detail

Siemens Industry, Inc.

Building Technologies Division

A6V10315044_enUS_c3

PRE-INSTALLATION Before connecting either the printer, power or the UFP, the network address must be

set for the FCA2018-U1 using the three-position switch. (Refer to Figure 2 for the

location of the switch.) The address for the FCA2018-U1 must be the same as the

address selected for it in the FS20 Configuration Tool. To increment each digit of the

address, press the “+” button above the desired digit; to decrement each digit, press

the “-” button below the desired digit.The range of allowable addresses is from 001

to 8 (leading zeros must be used).

If the FCA2018-U1 is located at the end of the UFP network (Style 4 only), the termi-

nation switch must be set to ON. Otherwise it must be set to OFF.

Figure 3

Installing The FCA2018-U1 Terminal Block Covers

Figure 4

Connecting The Printer To The FCA2018-U1

120 VAC

60 Hz. CENTRONICS

PARALLEL

PAL-1 or EDP LISTED PRINTER

FCA2018-U1

SPP

CABLE SUPPLIED WITH FCA2018-U1

SUPERVISED

POWER LIMITED

Two terminal block covers are provided with the FCA2018-U1. Each comes as two

separate parts, a lower bracket which has a ¾ inch conduit opening and a cover.

Attach the lower bracket to each end of the FCA2018-U1 using four of the #10 nuts

provided in the FCA2018-U1 hardware kit. Reserve the covers and the remaining

hardware until the FCA2018-U1 is mounted and wired.

Mount the FCA2018-U1 to either the wall or desk where the PAL-1 is located. Use

the four mounting holes in the lower bracket.

NOTES:

1. The maximum distance from the FCA2018-U1 to the PAL-1 is 6 feet.The two modules must be in the same room.

2. For NFPA 72 Local, Auxiliary and Remote Station configurations, connect the output of the FCA2018-U1 to any

UL EDP listed printer.

3. The printer must support the EPSON FX command set.

4. For NFPA 72 Proprietary of UL 1076 configurations use printer SIEMENS Model PAL-1, a UL listed for fire Centronics parallel printer.

5. The printer is supervised for AC loss, off line, paper out, paper jam, and connection to the FCA2018-U1.

6. After loading the paper in the PAL-1 printer, turn off the power and follow the steps below.

• While pressing the LOAD PARK button, turn on the power to the PAL-1 printer. Keep pressing the LOAD PARK button for 5 seconds.

• Release the LOAD PARK button.

• The current setting will print.

• When printing is completed, the ON LINE indicator will be lit. If the ON LINE indicator is not lit, press the ON LINE button.

Siemens Industry, Inc.

Building Technologies Division

A6V10315044_enUS_c4

WIRING

Remove all system power before installation, first battery then AC. (To power up,

connect the AC first, then the battery.)

The PAL-1 is connected to the FCA2018-U1 with a standard PC printer cable. This

cable is supplied with the FCA2018-U1. Connect the PAL-1 to the FCA2018-U1 using

this cable. The two ends of the cable are different, ensuring proper connection. See

Figure 4.

The FCA2018-U1 requires 24VDC to operate.This power is available on the Aux

PowerTerminal (X1001) on the FS20 Periboard. See Figure 5 for wiring details.

Figure 5

Connecting Power To The FCA2018-U1

NOTES:

1. 18 AWG min., 12 AWG max.

2. Power limited to NFPA72

per NEC 760.

3. No end of line device

required.

4. 50Ωmax. total wire

resistance.

5. Refer to FS20 Product Data

Manual, P/N A6V10315015,

for ground fault detection

impedance.

CHASSIS GROUND

24V INPUT

TO FC360, X1_N

SUPERVISED &

POWER LIMITED

TO FC360, X1_P

The FCA2018-U1 can be connected to the UFP Style 6 or Style 4. Refer to the FS20

configuration for the proper Style. If the FCA2018-U1 is connected at the end, care

must be taken to properly terminate the UFP. See Figure 6 for the wiring instructions

when the FCA2018-U1 is connected as Style 6 and Figure 7 when the FCA2018-U1 is

connected as Style 4.

12 3 45 6

SHIELD

FCA2018-U1 UFP

TERMINAL BLOCK

12 3 456

SHIELD

FCA2018-U1 UFP

TERMINAL BLOCK

FC2016-U1

RS485 Module

X2-4 X2-3 X2-2 X2-1

RS485

AF RS485

RS485

BF RS485

SUPERVISED &

POWER LIMITED

DO NOT USE DO NOT USE

FIRST MODULE LAST MODULE

Figure 6

FCA2018-U1 Style 6 Wiring Configuration

NOTES:

1. 18 AWG min., 12 AWG max.

2. 2000 ft max between RS485

Module and FCA2018-U1.

3. Use twisted pair or shielded

twisted pair.

4. Terminate shield at one end

only.

5. Power limited to NFPA72

per NEC 760.

6. Reference RS485 Module

Installation Instructions,

Document ID A6V10334252.

Siemens Industry, Inc.

Building Technologies Division

A6V10315044_enUS_c5

Figure 7

FCA2018-U1 Style 4 Wiring Configuration

NOTES:

1. No end of line resistor

required.Termination set to

OFF except on the

FCA2018-U1 is at the end of

UFP network where the

Termination is set to ON.

2. 18 AWG min., 12 AWG max.

3. 2000 ft max between RS485

Module and FCA2018-U1.

4. Use twisted pair or shielded

twisted pair.

5. Terminate shield at one end

only.

6. Power limited to NFPA72

per NEC 760.

7. Reference RS485 Module

Installation Instructions,

Docuemnt ID A6V10334252.

12 3 45 6

SHIELD

FCA2018-U1 UFP

TERMINAL BLOCK

FC2016-U1

RS485 Module

X2-4 X2-3 X2-2 X2-1

RS485

AF RS485

BF RS485

AR RS485

DO NOT USE

UPERVI

POWER LIMITED

TO NEXT UFP

MODULE

Figure 8

UPS Wiring Diagram

GND

120 VAC

UTILITY

POWER

SOURCE

DO NOT

USE

DO NOT

USE

POWER TO

PRINTER

120 VAC

SEE NOTE 4

INPUT

FAIL

TERMINAL BLOCK

LOCATED ON

UPS SYSTEM

CONTROL BOARD

TO HTRI-S/-D/-R INPUT TERMINALS.

PROGRAM AS NORMALLY CLOSED

TROUBLE CAUSING INPUT.

BATTERY

FAIL

NOTES:

1. All wires 14 AWG min.,

600V insulation.

2. Wiring to the printer must

be 14 AWG min., 600V

insulation in conduit.

3. Use the UPS ICS Lifeline

Model 9300057.

4. Standby Power require-

ments: 120 VAC, 0.6A for 24

hours.

The PAL-1 requires a standby power source in the event of the loss of primary input power

(AC mains). Refer to Figure 8 for the connection of a UPS to meet this requirement.

Siemens Industry, Inc.

Building Technologies Division

A6V10315044_enUS_c6

INSTALLATION The FCA2018-U1 mounts with two flanges on the side of the terminal block covers.

Select a smooth surface within 6 feet of the PAL-1 for the FCA2018-U1.

Position the FCA2018-U1 and attach it to the mounting surface using the four #6 self

tapping screws provided.

Install the terminal block covers using the 6 remaining #10 nuts. Refer to Figure 3.

ELECTRICAL RATINGS

24V Back Plane Current 0

Screw Terminal 24V Current 150mA Max.

6.2V Back Plane Current 0

24V Standby Current 150mA Max.

Output Power

CAN Network Pair 8V peak to peak max.

75mA max.

(during msg transmission)

Siemens Industry, Inc.

Building Technologies Division

A6V10315044_enUS_c7

This page was left intentionally blank

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ Document ID A6V10315044_enUS_c

This page was left intentionally blank

P/N A5Q00050826

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens SINUMERIK 840D sl Betriebsanleitung

Siemens

Siemens XCI2001-U1 Leitfaden

Siemens

Siemens ZN-31U Bedienungsanleitung

Siemens

Siemens SIMOCODE pro C Benutzerhandbuch

Siemens

Siemens HOTEL SOLUTION HTC3.2 Series Bedienungsanleitung

Siemens

Siemens simovert masterdrives Bedienungsanleitung

Siemens

Siemens SIRIUS ACT 3SU1400-1GE10-1AA0 Bedienungsanleitung

Siemens

Siemens SIMOCODE DP Bedienungsanleitung

Siemens

Siemens SIRIUS ACT 3SU18 N Series Bedienungsanleitung

Siemens

Siemens SIMATIC NET 6GK1110-1AA00 Bedienungsanleitung

Siemens

Siemens SIMOTION Stücklistenhandbuch

Siemens

Siemens SIWAREX FTC Anwendungshandbuch

Siemens

Siemens SIMOTION D4 Series Technisches Dokument

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens 3VA9.37-0VF10 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SICAM A8000 Series Bedienungsanleitung

Siemens

Siemens Modem Block Bedienungsanleitung

Siemens

Siemens RUGGEDCOM ROS Bedienungsanleitung

Siemens

Siemens SIMATIC NET Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens FMT-A-ADPT Bedienungsanleitung

Siemens

Siemens SIMOTICS CONNECT 600 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung