Siemens SIMATIC ET 200SP HA Bedienungsanleitung

SIMATIC

ET 200SP HA

Interface Module IM 155-6 PN HA

(6DL1155-6AU00-0PM0)

Manual

05/2017

A5E39262148-AA

Security information 1

Product overview 2

Wiring 3

Parameters 4

Maintenance 5

Displays and interrupts 6

Technical specifications 7

Diagnostic messages A

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be

used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property

damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified

personnel are those who, based on their training and experience, are capable of identifying risks and avoiding

potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended or

approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described.

Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in

this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E39262148-AA

Ⓟ 05/2017 Subject to change

Table of contents

1 Security information......................................................................................................................................5

2Product overview..........................................................................................................................................7

2.1 Properties.................................................................................................................................7

3Wiring.........................................................................................................................................................11

3.1 Pin assignment.......................................................................................................................11

3.2 Schematic circuit diagram......................................................................................................13

4 Parameters.................................................................................................................................................15

4.1 Parameter assignment...........................................................................................................15

5 Maintenance...............................................................................................................................................17

5.1 Exchanging the BusAdapter or interface of the distributed I/O..............................................17

6 Displays and interrupts...............................................................................................................................19

6.1 Status and error displays.......................................................................................................19

6.2 Interrupts................................................................................................................................23

7 Technical specifications..............................................................................................................................25

A Diagnostic messages.................................................................................................................................31

A.1 Diagnostics messages and maintenance events...................................................................31

Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)

Manual, 05/2017, A5E39262148-AA 3

Table of contents

Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)

4Manual, 05/2017, A5E39262148-AA

Security information 1

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines, and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions only form one element of such a concept.

Customer is responsible to prevent unauthorized access to its plants, systems, machines and

networks. Systems, machines and components should only be connected to the enterprise

network or the internet if and to the extent necessary and with appropriate security measures

(e.g. use of firewalls and network segmentation) in place.

Additionally, Siemens’ guidance on appropriate security measures should be taken into

account. For more information about industrial security, please visit:

http://www.siemens.com/industrialsecurity.

Siemens’ products and solutions undergo continuous development to make them more secure.

Siemens strongly recommends to apply product updates as soon as available and to always

use the latest product versions. Use of product versions that are no longer supported, and

failure to apply latest updates may increase customer’s exposure to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under

http://www.siemens.com/industrialsecurity.

Validity of the documentation

This product manual describes the IM 155-6 PN HA interface module with the article number

6DL1155-6AU00-0PM0.

It supplements the system manual of the

ET 200SP HA Distributed I/O System

Functions that generally relate to the system are described in this manual.

The information in this product manual, system manual and function manual enables you to

commission the ET 200SP HA distributed I/O system.

Conventions

Please also observe notes marked as follows:

Note

A note contains important information on the product described in the documentation, on the

handling of the product, or on the section of the documentation to which particular attention

should be paid.

Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)

Manual, 05/2017, A5E39262148-AA 5

Security information

Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)

6Manual, 05/2017, A5E39262148-AA

Product overview 2

2.1 Properties

View

①Module type and designation ⑧MAC address (specific address for this exact module)

②LED for operating state ⑨Function status and firmware version

③LED for diagnostics ⑩Article number

④LED for maintenance ⑪Connector for supply voltage

⑤2D matrix code ⑫Slot for PROFINET BusAdapter

⑥LED for master operation ⑬PROFINET BusAdapter

⑦LED for supply voltage ⑭Terminal block for interface module (figure: for redundant

interface modules)

Figure 2-1 View of IM 155‑6 PN HA

Properties

The IM 155‑6 PN HA, together with the carrier and BusAdapter, forms the interface of the

ET 200SP HA.

The interface is used for communication between the CPU and the connected ET 200SP HA

I/O modules via PROFINET IO.

Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)

Manual, 05/2017, A5E39262148-AA 7

The interface has the following technical properties:

● Supply voltage 1L+ 24 V DC (SELV/PELV).

The supply voltage is fed via the carrier module.

The connection plug is included in the scope of delivery of the interface module.

● PROFINET IO connection via BusAdapter (see following paragraph, "Accessories")

The interface supports the following functions:

● Firmware update

● I&M identification data

● Pulling and plugging modules in RUN

● Value status QI

● IO redundancy

● Time stamping

● Multi Hot Swap (pulling/plugging of multiple I/O modules during operation)

● Saving service data

● Recording the value status of I/O modules

● Reference temperature distribution

You can configure the interface with HW Config and integrate it into your system

Note

The IM 155‑6 PN HA cannot be pulled/plugged when the associated connector for the supply

voltage is plugged in.

PROFINET IO functions

The interface supports the following PROFINET IO functions:

● Integrated BusAdapter with 2 ports

● Supported Ethernet services: ping, arp, network diagnostics (SNMP)/MIB-2, LLDP-MIB and

MRP-MIB

● Port diagnostics

● Disabling of ports

● Minimum update time of 250 µs

● Device replacement without programming device (PG)

● Reset to factory settings via PROFINET IO

● System redundancy S2

● System redundancy R1

● Media redundancy (MRP)

● Support of submodules on suitable I/O modules

Product overview

2.1 Properties

Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)

8Manual, 05/2017, A5E39262148-AA

Accessories

The following accessories must be ordered separately:

BusAdapter

● BusAdapter BA 2×RJ45 (6DL1-6AR00-0AA0) - adapter for Ethernet cable with RJ45

connector

● BusAdapter BA 2×FC (6DL1-6AP00-0AA0) - adapter for direct connection of the Fast

Connect bus cable

● BusAdapter BA 2×LC (6DL1-6AG00-0AA0) - adapter for glass fiber optic cable with

IE FC FO connector

Carrier modules

● Carriers for the IM 155‑6 PN HA are available in the following variants:

– Carrier for one IM 155‑6 PN HA

– Carrier for two IM 155‑6 PN HA for redundant configuration

The carriers connect the IM 155‑6 PN HA to the backplane bus. They enable data exchange

with the I/O modules.

Server module and power bus cover

● The server module and power bus cover are included in the product package of the carrier

module and are available separately as accessories.

● The server module and power bus cover terminate the configuration of the ET 200SP HA.

● Place the server module and the power bus cover at the end of the configuration.

The power bus cover serves to protect the power bus contacts.

Marking options

● Labeling strips

● Reference identification label

Product overview

2.1 Properties

Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)

Manual, 05/2017, A5E39262148-AA 9

Product overview

2.1 Properties

Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)

10 Manual, 05/2017, A5E39262148-AA

Andere Handbücher für SIMATIC ET 200SP HA

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens SINUMERIK 828D Turning Betriebsanleitung

Siemens

Siemens VAI61 Series Bedienungsanleitung

Siemens

Siemens SINAMICS G120 Bedienungsanleitung

Siemens

Siemens 599-06611 Betriebsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens SPCW110 Bedienungsanleitung

Siemens

Siemens SIRIUS 8WD4428-0BF Bedienungsanleitung

Siemens

Siemens SINAMICS G120P CU230P-2 Administratorhandbuch

Siemens

Siemens 6MB5110-1 Bedienungsanleitung

Siemens

Siemens P Series Bedienungsanleitung

Siemens

Siemens 6SE7024-1EP85-0AA1 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RA11 Bedienungsanleitung

Siemens

Siemens SIRIUS ACT 3SU18 N Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 840Di sl Bedienungsanleitung

Siemens

Siemens SIMATIC IM 153-2 Bedienungsanleitung

Siemens

Siemens ACVATIX PS53 Bedienungsanleitung

Siemens

Siemens FDCI221 Bedienungsanleitung

Siemens

Siemens SINAMIC G130 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SIMATIC FM 351 Bedienungsanleitung

Siemens

Siemens SCALANCE W788C-2 Bedienungsanleitung

Siemens

Siemens SIMOCODE pro Bedienungsanleitung

Siemens

Siemens SINUMERIK 802D sl Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung