Siemens MICROMASTER 411 Bedienungsanleitung

MICROMASTER 411 & COMBIMASTER 411

AS-i Module

Operating Instructions Issue 01/03

User Documentation

6SE6400-5AT00-0BP0

MICROMASTER 411 &

COMBIMASTER 411

AS-i Module

Operating Instructions

User Documentation

Valid for

Issue 01/03

MICROMASTER 411 &

COMBIMASTER 411

Issue 01/03

Description 1

Installing the AS-i

Module

Commissioning 3

Diagnostics and

Troubleshooting

Technical Data 5

MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions

46SE6400-5AT00-0BP0

Further information is available on the Internet under:

http://www.siemens.de/micromaster

Approved Siemens Quality for Software and Training

is to DIN ISO 14001, Reg. No. 2160-01

The reproduction, transmission or use of this document,

or its contents is not permitted unless authorized in

writing. Offenders will be liable for damages. All rights

including rights created by patent grant or registration of a

utility model or design are reserved.

MICROMASTER® is a registered trademark of Siemens.

Other functions not described in this document may be

available. However, this fact shall not constitute an

obligation to supply such functions with a new control, or

when servicing.

We have checked that the contents of this document

correspond to the hardware and software described.

There may be discrepancies nevertheless, and no

guarantee can be given that they are completely identical.

The information contained in this document is reviewed

regularly and any necessary changes will be included in

the next edition. We welcome suggestions for

improvement.

Siemens handbooks are printed on chlorine-free paper

that has been produced from managed sustainable

forests. No solvents have been used in the printing or

binding process.

Document subject to change without prior notice.

Order Number. 6SE6400-5AT00-0BP0

Printed in the Federal of Germany

Siemens-Aktiengesellschaft.

Issue 01/03 Foreword

MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions

6SE6400-5AT00-0BP0 5

Foreword

User Documentation

WARNING

Before installing and commissioning the inverter, you must read all safety

instructions and warnings carefully including all the warning labels attached to the

equipment. Make sure that the warning labels are kept in a legible condition and

replace missing or damaged labels.

Information is also available from:

Technical Support Nuremberg

Tel: +49 (0) 180 5050 222

Fax: +49 (0) 180 5050 223

Email: techsupport@ad.siemens.de

Internet Home Address

Customers can access technical and general information at:

http://www.siemens.de/micromaster

Contact address

Should any questions or problems arise while reading this manual, please contact

the Siemens office concerned using the form provided at the back this manual.

Definitions and Warnings Issue 01/03

MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions

66SE6400-5AT00-0BP0

Definitions and Warnings

Safety guidelines

This manual contains notices intended to ensure your personal safety, as well as to

protect products and connected equipment against damage. Information relating to

your personal safety is highlighted by a warning triangle. Warnings about property

damage are displayed without a warning triangle. Depending on the degree of risk

involved, safety-related information is presented in the following categories:

DANGER

For the purpose of this documentation and the product warning labels, "Danger"

indicates that death, severe personal injury or substantial damage to property will

result if proper precautions are not taken.

WARNING

For the purpose of this documentation and the product warning labels, "Warning"

indicates that death, severe personal injury or substantial damage to property can

result if proper precautions are not taken.

CAUTION

With a warning triangle, "Caution" indicates that minor personal injury can result if

proper precautions are not taken.

CAUTION

Without a warning triangle, "Caution" indicates that material damage can result if

proper precautions are not taken.

ATTENTION

indicates that an undesirable effect or state can occur if attention is not paid to the

advice given.

NOTE

For the purpose of this documentation, "Note" indicates important information

relating to the product or highlights part of the documentation for special attention.

Qualified personnel

For the purpose of this Instruction Manual and product labels, a "Qualified person"

is someone who is familiar with the installation, mounting, start-up and operation of

the equipment and the hazards involved.

He or she must have the following qualifications:

1. Trained and authorized to energize, de-energize, clear, ground and tag circuits

and equipment in accordance with established safety procedures.

2. Trained in the proper care and use of protective equipment in accordance with

established safety procedures.

3. Trained in rendering first aid.

Issue 01/03 Definitions and Warnings

MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions

6SE6400-5AT00-0BP0 7

User Documentation

WARNING

Before installing and commissioning, please read these safety instructions and

warnings carefully and all the warning labels attached to the equipment. Make sure

that the warning labels are kept in a legible condition and replace missing or

damaged labels.

Proper use

Please note the following:

WARNING

This equipment contains dangerous voltages and controls potentially dangerous

rotating mechanical parts.

Non-compliance with Warnings or failure to follow the instructions contained in this

manual can result in loss of life, severe personal injury or serious damage to

property.

Only suitably qualified personnel should work on this equipment, and only after

becoming familiar with all safety notices and maintenance procedures contained in

this manual.

The successful and safe operation of this equipment is dependent upon its proper

handling, storage, installation, operation and maintenance.

National safety regulations are also applicable.

Use for intended purpose only

The equipment may be used only for the application stated in the manual and only

in conjunction with devices and components recommended and authorized by

Siemens.

Table of Contents Issue 01/03

MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions

86SE6400-5AT00-0BP0

Table of Contents

1 Description............................................................................................................... 9

2 Installing the AS-i Module .................................................................................... 11

2.1 Preparation of Inverter Terminal Housing ............................................................... 12

2.2 AS-i Module Installation .......................................................................................... 13

2.3 Addressing the AS-i Module.................................................................................... 15

3 Commissioning ..................................................................................................... 17

3.1 Parameter settings .................................................................................................. 17

3.2 AS-i Module Parameters ......................................................................................... 18

3.3 AS-i use data........................................................................................................... 19

4 Diagnostics and Troubleshooting ....................................................................... 21

5 Technical Data ....................................................................................................... 23

5.1 Technical Specifications.......................................................................................... 23

5.2 EMC Information ..................................................................................................... 23

Issue 01/03 Description

MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions

6SE6400-5AT00-0BP0 9

1 Description

The AS-i Module (Actuator sensor-Interface Communications Module) has been

designed to control the COMBIMASTER 411 and MICROMASTER 411 inverters

via:

 ON/OFF commands

 Fixed frequency selection

 Reverse commands

 Fault acknowledge commands

In the standard AS-i system up to 31 slaves can be connected, each slave having

up to 4 input and output bits.

Without the use of repeaters or extenders the maximum length of a cable segment

in the network is 100 meters (328 feet).

The AS-i Module is connected to the network via the FK cable adapter on the lower

housing of the module casing by a simple two-wire cable without any shielding; this

cable supplies both the data path and power supply to the slave nodes

simultaneously.

Contact needles pierce the cable through the cable insulation and make contact

with the copper conductors. When the cable is removed from the cable adaptor the

outer insulation of the cable self-seals the holes made by the cable adaptor

needles.

Figure 1-1 on page 10 shows the general layout and connections of the AS-i

Module.

Description Issue 01/03

MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions

10 6SE6400-5AT00-0BP0

Figure 1-1 View of the COMBIMASTER 411 & MICROMASTER 411 AS-i Module

Andere Handbücher für MICROMASTER 411

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC NET SCALANCE W760 Series Merkblatt

Siemens

Siemens SIMATIC S7 3964 Gebrauchsanweisung

Siemens

Siemens SIMOTICS CONNECT 400 Bedienungsanleitung

Siemens

Siemens SINAMICS V60 Bedienungsanleitung

Siemens

Siemens RVD240 Bedienerhandbuch

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC EP200SP Bedienungsanleitung

Siemens

Siemens multiranger 200 Benutzerhandbuch

Siemens

Siemens SED2-LONI/F Bedienungsanleitung

Siemens

Siemens PM240 Montageanleitung

Siemens

Siemens Desigo PXC4.E16 Bedienungsanleitung

Siemens

Siemens SIMATIC CPU 1515SP PC2 F Bedienungsanleitung

Siemens

Siemens Flowrite 599 Series Betriebsanleitung

Siemens

Siemens SIMATIC 6DL1 136-6AA00-0PH1 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SIRIUS Star-Delta Combination S2 Bedienungsanleitung

Siemens

Siemens SIMATIC S7-400H Bedienungsanleitung

Siemens

Siemens MVS661 N Series Bedienungsanleitung

Siemens

Siemens Simatic S7-300 Bedienungsanleitung

Siemens

Siemens SPCW110 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIRIUS 8WD4428-0B Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung