Siemens P1 BIM Bedienungsanleitung

Installation Instructions

Document No. 553-140

November 4, 2019

TX-I/O P1 Bus Interface Module

Item Number: 553-140, Rev. GA Page 1 of 4

Product Description

The P1 Bus Interface Module (P1 BIM) enables

communication between a P1 Field Level Network

(FLN) and TX-I/O modules. It also provides 14.4 W

(0.6A at 24 Vdc) to power the TX-I/O modules and

external devices. External devices draw power from

the 24 Vdc and ground terminals on the TX-I/O

modules.

Figure 1. P1 Bus Interface Module Example (TXB1.P1-4).

Product Numbers

TXB1.P1

TX-I/O Bus Interface Module, P1

(10 modules, if needed may share

power with TXS1.12F4 TX-I/O

Power Supply)

TXB1.P1-4

TX-I/O Bus Interface Module, P1

(4 modules)

Warning/Caution Notation

WARNING:

Personal injury or property

damage may occur if you do not

follow a procedure as specified.

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow a procedure as specified.

Required Tools and Materials

•Wire stripper/side cutter

•Small flat blade screwdriver

•Digital multimeter (DMM)

Expected Installation Time

7 minutes

Prerequisites

CAUTION:

No power wiring is connected to the field

panel controller or other TX-I/O

components at this time.

CAUTION:

The TX-I/O island bus must be mounted

on a DIN rail (1.38" × 0.3" × 0.04"

[35 mm × 7.5 mm × 1 mm]).

•For energy management installations, NEMA

Type 1 or better enclosure with DIN rails and

source of 24 Vac.

•For smoke control installations, PX Series

enclosures and service boxes. See the PX

Series Service Box Installation Instructions

(553-131).

•If mounting in an enclosure:

−Enclosure is installed.

−The power source is installed, as

applicable.

−The power is OFF.

•All necessary wiring is pulled and terminated

per the layout drawing.

•Power and communication wiring is terminated

to the removable plugs supplied with the

devices.

Document No. 553-140

Installation Instructions

November 4, 2019

Page 2 of 4Siemens Industry, Inc.

Power Requirements

One of the following power sources is pulled to the

enclosure:

•120 Vac, 60 Hz and terminated at the 115V

PX Series Service Box.

•230 Vac, 50/60 Hz and terminated at the 230V

PX Series Service Box.

•24 Vac, 50/60 Hz Class 1 power limited from a

third-party transformer and connected to a

terminal block.

•If powering a TX-I/O expansion panel, power

wiring is run from the transformer in the

primary panel to the expansion panel, if

needed.

CAUTION:

For information on extending the TX-I/O

island bus outside the enclosure, see the

APOGEE Wiring Guidelines for Field

Panels and Equipment Controllers

(125-3002).

General Installation Requirements

CAUTION:

All devices not isolated by an Island Bus

Expansion module (TXA1.1BE) must be

connected to the same grounding point.

CAUTION:

Do not connect TX-I/O components to a

floating system neutral. Otherwise,

equipment damage will occur.

•System Neutral ( ) must be

continuous throughout the TX-I/O

Bus.

•System Neutral must be connected

to building approved earth-ground

( ) at a single point only at the

24 Vac transformer.

Installation

CAUTION:

Turn OFF AC power at the ON/OFF

switch in the Service Box or

transformer enclosure.

CAUTION:

UL Listings require that NEC Class I

and Class II wiring be kept separate

from each other. Use separate conduit

and cable tie bars to separate Class I

Digital Output (DO) wires from all other

Class II wiring.

CAUTION:

The TX-I/O island bus must extend

from the male bus connector of the P1

Bus Interface Module (BIM).

- The P1 BIM supplies 24 Vac,

24 Vdc, and communication to I/O

modules on the male bus

connector.

CAUTION:

Only insert or remove the P1 BIM, TX-

I/O Power Supply, and Bus Connection

Module when the power is OFF.

This device includes electrical and

electronic components and must not

be disposed of as domestic waste.

Product recovery and disposal must

comply with all national and local

regulations.

NOTE:

For Smoke Control applications, the

field panel controller must be installed

in the lower half of the enclosure.

For more information, see TX-I/O I/O

Modules Installation for UL

Applications Installation Instructions

(553-141) and TX-I/O Power Supply

and Bus Modules Installation

Instructions (553-142).

Document No. 553-140

Installation Instructions

November 4, 2019

Siemens Industry, Inc. Page 3 of 4

Basic Steps for Connecting Devices to the

DIN Rail

The island bus establishes its own connection when

TX-I/O devices are plugged into one another on a DIN

rail.

1. Slide out the mounting tabs.

2. Align the channel on the back of the device with

the DIN rail.

3. Using a flat blade screwdriver, push in each

mounting tab until it clips onto the DIN rail.

4. Align an I/O module with the Power Supply or Bus

Connection Module and slide the I/O module

down over the TX-I/O island bus connector.

5. Push in each mounting tab until it clips onto the

DIN rail.

Connecting Devices to the TX-I/O Island Bus.

Completing the Installation

CAUTION:

For RS-485 ALN or FLN, terminate only one

end of the shield wire on the enclosure earth

ground.

For a 3-wire system, terminal is connected

to reference wire. Protective ground terminal

may be connected to earth ground.

For a 2-wire system, terminal is not

connected. Protective ground terminal must

be connected to earth ground.

NOTE: Do not connect the power or network

communication cable until instructed to do so

during start-up.

1. Terminate power wiring to the 24 Vac removable

plug.

2. If necessary, terminate wires to the

communications terminals (CS and CD).

The installation is now complete.

Document No. 553-140

Installation Instructions

November 4, 2019

Unrestricted Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make

changes as design improvements are introduced. APOGEE and Insight are registered trademarks of Siemens Industry, Inc. Other product or

Siemens Industry, Inc.

Smart Infrastructure

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

+1 847-215-1000

Your feedback is important to us. If you have

comments about this document, please send them

to sbt_technical.editor.us.sbt@siemens.com.

Document No. 553-140

Printed in the USA

Page 4 of 4

Configuring the 4-Module P1 BIM

1. Power up the P1 BIM.

2. Plug in the USB on both ends (the device side to

the P1 BIM; the host side to the computer).

The device will be automatically recognized and

installed.

3. Open Windows Explorer.

4. Find the USB device/drive (will say SIEMENS

P1BIM Configuration Tool) in the drives list.

5. Open the drive.

6. Double-click P1BIMCFG.exe to launch the

application.

The following dialogue box displays:

7. Select the desired Baud Rate from the drop-down

menu. (Note: Only 4800 and 38400 are supported

rates.)

8. Click Apply.

9. Verify that the baud rate you selected is displayed

in the Baud Rate field.

10. Enter the desired address in the P1 Address field.

The default address is 99, but the device will not

communicate if left at the default address. Valid

P1 addresses are 1 through 98.

11. Click Apply.

12. Verify that the address you entered is displayed in

the P1 Address field.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens EFB300 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D Einrichtungshandbuch

Siemens

Siemens SIRIUS 3RW5 series Bedienungsanleitung

Siemens

Siemens SINUMERIK 808D Kurzanleitung

Siemens

Siemens SIRIUS 3RA2130-4 A3 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK Series Stücklistenhandbuch

Siemens

Siemens SIMATIC Technisches Dokument

Siemens

Siemens SIDOOR ATD4 W Series Benutzerhandbuch

Siemens

Siemens SINAMICS S120 Stücklistenhandbuch

Siemens

Siemens SIMOCODE pro Bedienungsanleitung

Siemens

Siemens V-2030 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Stücklistenhandbuch

Siemens

Siemens VRD Series Betriebsanleitung

Siemens

Siemens SINUMERIK 828D Turning Bedienungsanleitung

Siemens

Siemens SINUMERIK 808D Bedienungsanleitung

Siemens

Siemens LOGO! CMR2020 Bedienungsanleitung

Siemens

Siemens RWF50 Benutzerhandbuch

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens SIRIUS 3RW44 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens Siprotec DNP3 IP Gebrauchs- und Pflegehandbuch

Siemens

Siemens DESIGO PXM20 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500/ET 200MP Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung