Siemens SIMATIC 8DO 24 V DC/0.5 A HF Bedienungsanleitung

SIMATIC ET 200S distributed I/O Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

_____________

Properties 1

Parameters

Diagnostics

SIMATIC

ET 200S distributed I/O

Digital electronic module 8DO

DC24V/0.5A HF (6ES7132-4BF00-

0AB0)

Manual

10/2009

A5E02515349-01

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE

indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation for the specific task, in particular its warning notices and

safety instructions. Qualified personnel are those who, based on their training and experience, are capable of

identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be adhered to. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E02515349-01

Ⓟ 09/2009

Technical data subject to change

Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Manual, 10/2009, A5E02515349-01 3

Table of contents

1 Properties .................................................................................................................................................. 5

1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0) ....................................5

2 Parameters.............................................................................................................................................. 11

2.1 Parameters...................................................................................................................................11

3 Diagnostics.............................................................................................................................................. 13

3.1 Diagnostics using LED display.....................................................................................................13

3.2 Error types....................................................................................................................................14

Table of contents

Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

4 Manual, 10/2009, A5E02515349-01

Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Manual, 10/2009, A5E02515349-01 5

Properties 1

1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-

0AB0)

Properties

● Digital electronic module with eight outputs

● Output current 0.5 A per output, aggregate current 4 A

● Rated load voltage 24 VDC

● Diagnostics: wire break

● Short-circuit protection

● Suitable for solenoid valves, DC contactors, and indicator lights

● Supports isochronous operation

Requirements for operation

It is possible to operate the 8DO 24 V DC/0.5 A HF digital electronic module with the

following interface modules, as of the specified order numbers:

Interface module Order number (or higher) Firmware version (or

higher)

IM 151-1 STANDARD

IM 151-1 FO STANDARD

IM 151-1 HIGH FEATURE

6ES7151-1AA05-0AB0

6ES7151-1AB05-0AB0

6ES7151-1BA02-0AB0

V2.2.4

---

V2.2.3

IM 151-3 PN

IM 151-3 PN FO

IM 151-3 PN HIGH FEATURE

6ES7151-3AA23-0AB0

6ES7151-3BB23-0AB0

6ES7151-3BA23-0AB0

V6.1

IM 151-1 BASIC 6ES7151-1CA00-0AB0 ---

IM151-1 COMPACT 6ES7151-1CA00-1BL0

6ES7151-1CA00-3BL0

---

IM 151-7 CPU

IM 151-7 CPU FO

IM 151-7 F-CPU

6ES7151-7AA20-0AB0

6ES7151-7AB00-0AB0

6ES7151-7FA20-0AB0

---

IM 151-8 PN/DP CPU

IM 151-8 PN/DP F-CPU

6ES7151-8AB00-0AB0

6ES7151-8FB00-0AB0

---

Properties

1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

6 Manual, 10/2009, A5E02515349-01

General terminal assignment

Note

Terminals A4, A8, A3 and A7 are only available at specified terminal modules.

Terminal assignment for 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Terminal Assignment Terminal Assignment Notes

1 DO

0 5 DO

2 DO

2 6 DO

3 DO

4 7 DO

4 DO

6 8 DO

A4 AUX1 A8 AUX1

A3 AUX1 A7 AUX1

•DOn: Output signal, Channel n

•AUX1: M chassis ground (from power module) or potential bus

(freely usable up to 230 VAC)

Usable terminal modules

Terminal assignment for 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

TM-E15C26-A1

(6ES7193-4CA50-0AA0)

TM-E15C24-01

(6ES7193-4CB30-0AA0)

Spring terminal

TM-E15S26-A1

(6ES7193-4CA40-0AA0)

TM-E15S24-01

(6ES7193-4CB20-0AA0)

Screw-type terminal

TM-E15N26-A1

(6ES7193-4CA80-0AA0)

TM-E15N24-01

(6ES7193-4CB70-0AA0)

Fast Connect



$8;

































0$8;

FRQGXFWRU

&RQQHFWLRQH[DPSOHV

Properties

1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Manual, 10/2009, A5E02515349-01 7

Two-wire connection

The following configuration example shows a 2-wire connection with the electronic modules

8DO DC24V. You require further terminals so that sufficient terminals are available for the

chassis ground connection M when the TM-E15S26-A1 terminal modules are used. In the

example this is implemented by the add-on terminal TE-U120S4x10 that can be mounted as

from a width of 120 mm (8 EMs). You can naturally also use other terminals for this

configuration (for example, ET 200S potential distribution module 4POTDIS).















   



          

 

             



 

 







$$$$$ $$$$$$$$$$ $

$$$$

$8;



'&9

① Terminal module TM-P15S23-A0

② Power module PM-E 24 VDC

③ Electronic modules 8DI DC24V

④ Terminal modules TM-E15S26-A1

⑤ Actuators in 2-wire connection

⑥ Add-on terminal TE-U120S4x10

Properties

1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

8 Manual, 10/2009, A5E02515349-01

Block diagram

















3

3

0

/

(76

%DFNSODQHEXV

LQWHUIDFH

%DFNSODQHEXV

5HYHUVHSRODULW\

SURWHFWLRQ

Figure 1-1 Block diagram 8DO DC24V/0.5A HF

Properties

1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Manual, 10/2009, A5E02515349-01 9

Technical data 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Dimensions and weight

Width (mm) 15

Weight Approx. 40 g

Module-specific data

Supports isochronous operation Yes

Number of outputs 8

Length of cable

•Unshielded max. 600 m

•Shielded max. 1,000 m

Parameter length 3 bytes

Address space 1 byte

Voltages, currents, potentials

Rated load voltage L+ (from the power module) 24 VDC

•Reverse polarity protection Yes1

Total current of the outputs (per module) 4 A

Electrical isolation

•Between the channels No

•Between the channels and backplane bus Yes

Permissible potential difference

•Between the different circuits 75 VDC / 60 VAC

Insulation tested 500 VDC

Current consumption

•From the rated load voltage L+ (no load) Max. 5 mA per channel

Power dissipation of the module Typically 1.5 W

Status, interrupts, diagnostics

Status display Green LED per channel

Diagnostics function

•Group error Red "SF" LED

•Diagnostic functions readable Yes

Data for selecting an actuator

Output voltage

•At signal "1" Min. L+ (-1 V)

Output current

•At signal "1"

– Rated value

– Permitted range

0.5 A

7 mA up to 0.6 A

•With signal "0" (leakage current) max. 0.3 mA

Output delay (for resistive load)

Properties

1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)

10 Manual, 10/2009, A5E02515349-01

•At "0" to "1" max. 300 μs

•At "1" to "0" max. 600 μs

Load resistor range 48 Ω to 3.4 kΩ

Lamp load max. 5 W

Connecting two outputs in parallel

•For redundant triggering of a load Yes (per module)

•To increase performance No

Control of a digital input Yes

Switch rate

•For resistive load 100 Hz 2

•On inductive load 2 Hz 2

•For lamp load 10 Hz 2

Limitation (internal) of the voltage induced on

circuit interruption

typ. L + (-55 V)

Reverse-voltage proof Yes, if using the same load voltage as at the

power module

Short-circuit protection of the output Yes (per channel)3

1 Polarity reversal can lead to the digital outputs being connected through.

2 The diagnostic message "short circuit" is based on the thermal short-circuit detection in the output

driver.

3 limited to typ. 1.5 A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens PM330 Montageanleitung

Siemens

Siemens FDCIO223 Bedienungsanleitung

Siemens

Siemens Cerberus Pyrotronics LP-30 Bedienungsanleitung

Siemens

Siemens SINUMERIK 828D Turning Stücklistenhandbuch

Siemens

Siemens SINAMICS SM120 Bedienungsanleitung

Siemens

Siemens SIRIUS ACT 3SU1400-1EK10-6AA0 Bedienungsanleitung

Siemens

Siemens XC10 Series Leitfaden

Siemens

Siemens SIRIUS 3RA2130-4 A3 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Merkblatt

Siemens

Siemens Sinamics G120 CU240E Bedienungsanleitung

Siemens

Siemens Siwarex U Bedienungsanleitung

Siemens

Siemens 3VA9908-0BC Series Bedienungsanleitung

Siemens

Siemens SCALANCE S615 Bedienungsanleitung

Siemens

Siemens ANT792-6MN Administratorhandbuch

Siemens

Siemens SINUMERIK 840D Betriebsanleitung

Siemens

Siemens AP 118 Service-Handbuch

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens WATCHDOG-Modul ET 200iSP Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens TM Timer DIDQ Kurzanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens P Series Bedienungsanleitung

Siemens

Siemens SIMATIC TI505 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung