Siemens SIMATIC ET 200S Bedienungsanleitung

Power module PM-E DC24V HF

(6ES7138-4CA60- 

0AB0)

_________________

SIMATIC

ET 200S distributed I/O

Power module PM-E DC24V HF

(6ES7138-4CA60-0AB0)

Manual

06/2010

A5E02515369-02

Preface

Properties

Parameters

Diagnostics

Configuring

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE

indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation for the specific task, in particular its warning notices and

safety instructions. Qualified personnel are those who, based on their training and experience, are capable of

identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be adhered to. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E02515369-02

Ⓟ 06/2010

Technical data subject to change

Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

Manual, 06/2010, A5E02515369-02 3

Preface

Purpose of the manual

This manual supplements the

ET 200S Distributed I/O System

Operating Instructions.

General functions for the ET 200S are described in the ET 200S Distributed I/O System

Operating Instructions (http://support.automation.siemens.com/WW/view/en/1144348).

The information in this document along with the operating instructions enables you to

commission the ET 200S.

Basic knowledge requirements

To understand these operating instructions you should have general knowledge of

automation engineering.

Scope of the manual

This manual applies to this ET 200S module. It describes the components that are valid at

the time of publication.

Recycling and disposal

Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable. For

environmentally compliant recycling and disposal of your electronic waste, please contact a

company certified for the disposal of electronic waste.

Additional support

If you have any questions relating to the products described in this manual and do not find

the answers in this document, please contact your local Siemens representative

(http://www.siemens.com/automation/partners).

A guide to the technical documentation for the various SIMATIC products and systems is

available on the Internet. (http://www.siemens.com/simatic-docu).

The online catalog and ordering systems are available on the Internet

(http://www.siemens.com/automation/mall).

Training center

We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation

system. Please contact your regional training center or the central training center in D -

90327, Nuremberg, Germany (http://www.siemens.com/sitrain).

Preface

Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

4 Manual, 06/2010, A5E02515369-02

Technical Support

You can contact Technical Support for all Industry Automation products by means of the

Internet Web form for the Support Request

(http://www.siemens.com/automation/csi_en_WW/support_request).

Additional information about Siemens Technical Support is available on the Internet

(http://www.siemens.com/automation/csi_en_WW/service).

Service & Support on the Internet

In addition to our documentation, we offer a comprehensive knowledge base on the Internet

(http://www.siemens.com/automation/csi_en_WW/support).

There you will find:

● Our Newsletter, which constantly provides you with the latest information about your

products.

● The right documentation for you using our Service & Support search engine.

● The bulletin board, a worldwide knowledge exchange for users and experts.

● Your local contact for Automation & Drives in our contact database.

● Information about on-site services, repairs, spare parts, and lots more.

Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

Manual, 06/2010, A5E02515369-02 5

Table of contents

Preface ...................................................................................................................................................... 3

1 Properties .................................................................................................................................................. 7

1.1 Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)...........................................................7

2 Parameters.............................................................................................................................................. 11

2.1 Parameters for PM-E DC24V HF.................................................................................................11

3 Diagnostics.............................................................................................................................................. 13

3.1 Diagnostics using LED display.....................................................................................................13

3.2 Error types....................................................................................................................................14

4 Configuring .............................................................................................................................................. 15

4.1 Configuring the address space ....................................................................................................15

Table of contents

Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

6 Manual, 06/2010, A5E02515369-02

Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

Manual, 06/2010, A5E02515369-02 7

Properties 1

1.1 Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

Properties

● The PM-E DC24V HF power module monitors the supply voltage for all electronic

modules in the voltage group. The supply voltage is fed in by means of the TM-P terminal

module.

● You can use all the electronic modules except the 2DI AC120V ST, 2DI AC230V ST, and

2DO AC24..230V/1A in the voltage group of the PM-E DC24V HF power module.

● The current status of the power module is stored in the status byte in the process input

image (PII). This is updated irrespective of whether the "No Load Voltage" diagnosis has

been enabled.

● The PM-E DC24V HF power module is suitable for fail-safe modules.

● Extended temperature range from 0 to 55°C with vertical installation.

CAUTION

If you do not maintain the indicated load voltage of 24V DC, the result may be

dangerous plant conditions.

The result may be damages to the ET 200S or minor personal injuries.

Only connect the specified load voltage of 24V DC to the TM-P terminal module of the

power module. The connected load voltage must correspond to the supply voltage of the

electronic modules in the voltage group.

Requirements for operation

It is possible to operate the PM-E DC24V HF power module using the following interface

modules as of the order numbers specified.

Interface module as of order number Firmware version (or

higher)

IM 151-1 STANDARD 6ES7151-1AA05-0AB0 V2.2.4

IM 151-1 FO STANDARD 6ES7151-1AB05-0AB0 V2.2.4

IM 151-1 HIGH FEATURE 6ES7151-1BA02-0AB0 V2.2.3

IM 151-3 PN 6ES7151-3AA23-0AB0 V7.0.0

IM 151-3 PN FO 6ES7151-3BB23-0AB0 V7.0.0

IM 151-3 PN HIGH FEATURE 6ES7151-3BA23-0AB0 V7.0.0

IM 151-3 PN HIGH SPEED 6ES7151-3BA60-0AB0 V3.0.0

IM 151-8 PN/DP CPU 6ES7151-8AB01-0AB0 V3.2.0

IM 151-8F PN/DP CPU 6ES7151-8FB01-0AB0 V3.2.0

Properties

1.1 Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

8 Manual, 06/2010, A5E02515369-02

Maximum configuration per voltage group

The number of modules that can be connected depends on the total current of all modules in

a voltage group. This total must not exceed the maximum current carrying capacity.

Address space of inputs/outputs

Address space of inputs/outputs by selecting the following as an option:

Options Address space of the inputs Address space of the outputs

Status byte (S) 1 byte --

Option handling (O) 8 bytes 8 bytes

Status byte and option handling

(SO)

9-byte inputs 9 bytes (9th byte not relevant)

General terminal assignment

Note

Terminals A4 and A8 are only available at specified terminal modules.

Terminal assignment for PM-E DC24V HF (6ES7138-4CA60-0AB0)

Terminal Assignment Terminal Assignment Notes

2 L+ 6 L+

3 M 7 M

A4 AUX1 A8 AUX1

L+: Rated load voltage 24 VDC

M: Chassis ground

AUX1: Protective-conductor terminal or potential bus (freely usable

up to 230 VAC)

Properties

1.1 Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

Manual, 06/2010, A5E02515369-02 9

Usable terminal modules

Usable terminal modules for PM-E DC24V HF (6ES7138-4CA60-0AB0)

TM-P15C23-A1

(6ES7193-

4CC30-0AA0)

TM-P15C23-A0

(6ES7193-4CD30-

0AA0)

TM-P15C22-01

(6ES7193-4CE10-

0AA0)

Spring terminal

TM-P15S23-A1

(6ES7193-

4CC20-0AA0)

TM-P15S23-A0

(6ES7193-4CD20-

0AA0)

TM-P15S22-01

(6ES7193-4CE00-

0AA0)

Screw-type terminal

TM-P15N23-A1

(6ES7193-

4CC70-0AA0)

TM-P15N23-A0

(6ES7193-4CD70-

0AA0)

TM-P15N22-01

(6ES7193-4CE60-

0AA0)

Fast Connect

$8;

8; $$













$8;













$8;

 



'&9 '&9

3($8;

&RQQHFWLRQH[DPSOHV

Block diagram

'&9

3

3









3:5

5HDUSDQHOEXV

(76

EDFNSODQH

EXV

FRQQHFWLRQ

/RDGDQG

UHJHQHUDWLRQ

YROWDJH

PRQLWRULQJ

Figure 1-1 Block diagram of the PM-E DC24V HF power module

Properties

1.1 Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

Power module PM-E DC24V HF (6ES7138-4CA60-0AB0)

10 Manual, 06/2010, A5E02515369-02

Technical data PM-E DC24V HF (6ES7138-4CA60-0AB0)

Dimensions and weight

Dimension B (mm) 15

Weight Approx. 35 g

Voltages, currents, potentials

Rated load voltage 24 VDC

Overvoltage protection No

Protection with automatic circuit breakers Yes, tripping characteristic B, C

Max. current-carrying capacity 10 A

Short-circuit protection No

Electrical isolation

Between rated load voltage and backplane

bus Yes

Between the power modules Yes

Insulation test voltage 500 VDC

Current consumption

From the load voltage L+ (no load) max. 15 mA

Power dissipation of the module typ. 350 mW

Parameter length 3 bytes

Status, interrupts, diagnostics

Diagnostic function Yes

Group error Red "SF" LED

Load voltage monitoring Green "PWR" LED

Diagnostic information readable Yes

Andere Handbücher für SIMATIC ET 200S

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens SIMOTION D410 PN Bedienungsanleitung

Siemens

Siemens SIMOCODE pro DM-F Local Bedienungsanleitung

Siemens

Siemens SIRIUS Bedienungsanleitung

Siemens

Siemens FN2013-U1 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMOTION D4 5 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 802D sl Betriebsanleitung

Siemens

Siemens VAI61 Series Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP HA Bedienungsanleitung

Siemens

Siemens SITRANS F M MAGFLO series Bedienungsanleitung

Siemens

Siemens SENTRON 7KM PAC 4DI/2DO Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SINAMICS G120P CU230P-2 Administratorhandbuch

Siemens

Siemens SIRIUS 3TK2834 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840 Technisches Handbuch

Siemens

Siemens SM 338 Bedienungsanleitung

Siemens

Siemens RAB10 Series Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP CM 1xDALI Bedienungsanleitung

Siemens

Siemens SINUMERIK 840Di sl Bedienungsanleitung

Siemens

Siemens SIMATIC 505 PPX:505-6108A Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D Merkblatt

Siemens

Siemens HTRI-S Bedienungsanleitung

Siemens

Siemens SIPROTEC PROFINET IO Bedienungsanleitung

Siemens

Siemens SIMATIC 505 Betriebsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung