Siemens SIMATIC IM 153-2 Bedienungsanleitung

SIMATIC DP/PAink and Y Link bus links IM 153-2 Interface Module

_____________

Introduction

Description

Technical specifications

SIMATIC

DP/PA Link and Y Link bus links

IM 153-2 Interface Module

Product Information

08/2007

A5E01208363-01

Safety Guidelines

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE

indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Commissioning and

operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes

in this documentation qualified persons are defined as persons who are authorized to commission, ground and

label devices, systems and circuits in accordance with established safety practices and standards.

Prescribed Usage

Note the following:

WARNING

This device may only be used for the applications described in the catalog or the technical description and only

in connection with devices or components from other manufacturers which have been approved or

recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,

positioning and assembly as well as careful operation and maintenance.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Siemens AG

Automation and Drives

Postfach 48 48

90327 NÜRNBERG

GERMANY

Ordernumber: A5E01208363-01

Ⓟ 08/2007

Technical data subject to change

IM 153-2 Interface Module

Product Information, 08/2007, A5E01208363-01 3

Table of contents

1 Introduction................................................................................................................................................ 5

1.1 Introduction ....................................................................................................................................5

1.2 Compatibilities................................................................................................................................6

2 Description................................................................................................................................................. 7

2.1 Routing of frames of the slave initiative .........................................................................................7

2.2 Improved link behavior during commissioning...............................................................................7

2.3 Which devices can be operated behind the Y Link?......................................................................8

2.4 Operation of the link on an S5 H System.......................................................................................8

3 Technical specifications............................................................................................................................. 9

3.1 Technical specifications of the IM 153-2 (6ES7153-2BAx2-0XB0) ...............................................9

Table of contents

IM 153-2 Interface Module

4 Product Information, 08/2007, A5E01208363-01

IM 153-2 Interface Module

Product Information, 08/2007, A5E01208363-01 5

Introduction 1

1.1 Introduction

Scope

This Product Information supplements the

Bus Links DP/PA Coupler, DP/PA Link and Y Link

Operating Instructions (A5E00193840-16), Edition 10/2006, and describes the new features

of the interface modules:

● IM 153-2; order number 6ES7153-2BA02-0XB0

● IM 153-2 (outdoor); order number 6ES7153-2BA82-0XB0

The following information applies equally to both interface modules. If differences exist, the

relevant module will be identified explicitly.

Changes compared to the predecessor modules

In comparison to their predecessors (6ES7153-2BAx1-0XB0), the interface modules

indicated above contain the following new features:

● Routing of frames of the slave initiative

● The link behavior for commissioning has been improved.

Additional documentation

You will find the following supplementary documentation online at:

http://support.automation.siemens.com/WW/view/en/ with the corresponding entry ID

Name of manual Description

Operating Instructions

Bus Links

DP/PA Coupler, DP/PA Link and Y Link

Entry ID: 1142696

Description; application planning; mounting;

connecting; commissioning; operation of the

DP/PA Link and Y Link; maintenance and service;

functions; interrupt, error, and system messages,

technical specifications, basics about

PROFIBUS PA

System Manual

Principles of Explosion Protection

Entry ID: 12521844

Product overview, planning, commissioning, repair

and maintenance

Introduction

1.2 Compatibilities

IM 153-2 Interface Module

6 Product Information, 08/2007, A5E01208363-01

1.2 Compatibilities

Compatibility with predecessor versions

With regard to properties and features, the IM 153-2BAx2 interface module is fully

compatible with its predecessor versions. In addition, the new features indicated above are

available.

IM 153-2 Interface Module

Product Information, 08/2007, A5E01208363-01 7

Description 2

2.1 Routing of frames of the slave initiative

The IM 153-2BAx2 support routing of frames of the slave initiative. In so doing, the frames of

devices are passed behind the link to the higher-level controller.

This routing can be used, for example, to operate SINAMICS drives behind the Y Link if the

trace function is being used with the STARTER commissioning tool.

2.2 Improved link behavior during commissioning

Starting situation

The IM 153-2BAx2 interface modules are installed in one link and should be operated

redundantly in an H System (e.g., SIMATIC S7-400H).

Behavior of IM 153-2BAx2

If the IM 153-2BAx2 detects a redundancy partner that is not ready to be switched to or if

there are no lower-level slaves, the interface module stops sending continuous diagnostic

messages.

This behavior can also be implemented for the following interface modules by means of a

firmware update:

● IM 157 (6ES7157-0AA82-0XA0)

● IM 153-2 (6ES7153-2BAx1-0XB0)

This "new" behavior of the IM 153-2BAx2 is not available for redundancy mode in

accordance with the standard.

Description

2.3 Which devices can be operated behind the Y Link?

IM 153-2 Interface Module

8 Product Information, 08/2007, A5E01208363-01

2.3 Which devices can be operated behind the Y Link?

Slaves at the lower-level DP master system cannot be operated in DPV1 mode unless they

have been integrated and configured with GSD rev. ≥ 5.

The GSD must contain the following entries:

● Prm_Block_Structure_supp=1

● PrmCmd_supp=1

● Slave_Redundancy_supp=1

STEP 7

checks these entries during configuration.

If these entries are not found, the slave is then operated in DPV0 mode.

2.4 Operation of the link on an S5 H System

The following details are added to Chapter 11.1.2 of the

Bus Links; DP/PA Coupler,

DP/PA Link, and Y Link

Operating Instructions, Edition 10/2006:

S5-115H / -155H as DP master

A redundantly configured link with IM 153-2 can not be operated on an S5 H System.

IM 153-2 Interface Module

Product Information, 08/2007, A5E01208363-01 9

Technical specifications 3

3.1 Technical specifications of the IM 153-2 (6ES7153-2BAx2-0XB0)

Dimensions and weight

Dimension W x H x D (mm) 40 x 125 x 117

Weight Approx. 360 g

Module-specific data

Transmission speed for the higher level DP

master system

9.6; 19.2; 45.45; 93.75; 187.5; 500 kBaud

1.5; 3; 6; 12 MBaud

Bus protocol PROFIBUS DP

Frame length I / O data Max. 244 bytes

Length of configuration frame Max. 244 bytes

Length of diagnostic frame Max. 231 bytes

Length of parameter assignment frame Max. 223 bytes

suitable for system modifications during operation Yes

Voltages, currents, potentials

Rated supply voltage 24 VDC (20.4 V to 28.8 V)

•Polarity reversal protection Yes

•Power failure bypass 20 ms

Electrical isolation

•to a high-level DP master system Yes

•to the DP/PA or Y coupler No

Insulation tested with 500 VDC

when used in the DP/PA link

•Power consumption (24 VDC) Max. 200 mA (at 20.4 V)

•Power loss Max. 2.6 W (at 28.8 V)

when used in the Y link

•Power consumption (24 VDC) Max. 400 mA (at 20.4 V)

•Power loss Max. 3.6 W (at 28.8 V)

Technical specifications

3.1 Technical specifications of the IM 153-2 (6ES7153-2BAx2-0XB0)

IM 153-2 Interface Module

10 Product Information, 08/2007, A5E01208363-01

Status, interrupts, diagnostics

Status display No

Interrupts Yes

Diagnostics function Yes

•Group error Red LED "SF"

•Bus error on higher level DP master system Red LED "BF 1"

•Bus error on underlying bus system Red LED "BF 2"

•IM has an active channel Yellow LED "ACT"

•Monitoring 24 V power supply Green "ON" LED

Data for connecting underlying bus components

DP/PA coupler can be connected Max. 5

Y coupler can be connected 1

Underlying slaves can be connected Max. 64

Number of slots in underlying slaves (244 minus number of PA field devices), but not

more than 236

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens FCI1802-A2 Bedienungsanleitung

Siemens

Siemens MPS-6 Bedienungsanleitung

Siemens

Siemens RVD240 Bedienerhandbuch

Siemens

Siemens IM 153-4 PN Bedienungsanleitung

Siemens

Siemens SPCW110 Bedienungsanleitung

Siemens

Siemens SIRIUS ACT 3SU1400-1GE10-1AA0 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RW5 series Technisches Dokument

Siemens

Siemens Siwarex U Bedienungsanleitung

Siemens

Siemens SINUMERIK 840Di Handbuch

Siemens

Siemens SIMADYN D SS52 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Stücklistenhandbuch

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens simovert masterdrives Bedienungsanleitung

Siemens

Siemens IM 328-N Bedienungs- und Montageanleitung

Siemens

Siemens SIRIUS 3RA2712-.A Series Bedienungsanleitung

Siemens

Siemens V-2030 Bedienungsanleitung

Siemens

Siemens SIMATIC Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens SIMATIC IM 178-4 Bedienungsanleitung

Siemens

Siemens SIRIUS 3SB3 Bedienungsanleitung

Siemens

Siemens SIMATIC 6DL1131-6DF00-0PK0 Technisches Dokument

Siemens

Siemens SIRIUS ACT 3SU1 Benutzerhandbuch

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung