Siemens SINAMICS S120 Technisches Dokument
Equipment Manual 12/2004 Edition
sinamics
SINAMICS S120
Control Units and
A
dditional System Components
Preface
System Overview
1
Control Units
2
Additional System
Components
3
Encoder System Connection 4
Electromagnetic
Compatibility (EMC)
5
Spring-Loaded Terminals/
Screw Terminals
A
Abbreviations
B
References
C
SINAMICS
SINAMICS S120
Equipment Manual Control Units
and Additional System Components
Equipment Manual
(GH1), 12/2004 Edition
6SL3097-2AH00-0BP1
For further information please visit us at::
http://www.siemens.com/motioncontrol
This publication was produced with SIPS+
The reproduction, transmission or use of this document or its contents is
not permitted without express written authority. Offenders will be liable for
damages. All rights, including rights created by patent grant or registration
of a utility model or design, are reserved.
© Siemens AG, 2004. All rights reserved
We have checked that the contents of this document correspond to the
hardware and software described. Since deviations cannot be precluded
entirely, we cannot guarantee complete conformance. However, the data in
this manual is reviewed regularly and any necessary corrections included in
subsequent editions. We are thankful for any recommendations or
suggestions.
We reserve the right to make technical changes.
Order No. 6SL3097-2AH00-0BP1
Printed in Germany
Siemens Aktiengesellschaft
SINAMICS®-Documentation
Printing History
Brief details of this edition and previous editions are listed below.
The status of each edition is shown by the code in the "Remarks" column.
Status code in the "Comments" column:
A New Documentation
B Unrevised reprint with new order no.
C Revised edition with new status
If factual changes have been made on the page in relation to the same software version, this is indicated by a new edition coding in the
header on that page.
Edition Order No. Comments
12.04 6SL3097-2AH00-0BP1 C
Trademarks
SIMOVERT®, SIMATIC®, SIMATIC HMI®, SIMATIC NET®, SIMOTION®, SINUMERIK® and SINAMICS® are registered trademarks of
Siemens AG. The designations in this documentation whose use by third-parites for their own purpose may infringe the rights of the
owner.
Equipment Manual Control Units and Additional System Components
Equipment Manual, (GH1), 12/2004 Edition, 6SL3097-2AH00-0BP1 v
Preface
Information on the SINAMICS S documentation
The SINAMICS S documentation is divided into the following areas:
• General documentation / catalogs
• Manufacturer/service documentation
• Electronic documentation
This documentation is an integral part of the manufacturer/service documentation developed
for SINAMICS. All documents can be obtained separately.
You can obtain detailed information about the documents named in the documentation
overview and other documents available for SINAMICS from your local Siemens office.
For the sake of simplicity, this documentation does not contain all detailed information about
all types of the product and cannot cover every conceivable case of installation, operation, or
maintenance.
The contents of this documentation are not part of an earlier or existing agreement, a
promise, or a legal agreement, nor do they change this. All obligations entered into by
Siemens result from the respective contract of sale that contains the complete and sole valid
warranty arrangements. These contractual warranty provisions are neither extended nor
curbed as a result of the statements made in this documentation.
Audience
This documentation is aimed at machine and plant builders, commissioning engineers, and
service personnel who use SINAMICS.
Objective
This manual describes the hardware components of the SINAMICS S system. It provides
information about installation, electrical connection, and cabinet design.
Preface
Equipment Manual Control Units and Additional System Components
vi Equipment Manual, (GH1), 12/2004 Edition, 6SL3097-2AH00-0BP1
Danger and warning symbols - explanations
The following danger and warning notices are used in this document:
Danger
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury or in
substantial property damage.
Warning
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury or in
substantial property damage.
Caution
Used with the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury or in property damage.
Caution
Used without safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in
property damage.
Notice
Used without the safety alert symbol indicates a potential situation which, if not avoided, may result in an
undesirable result or state.
Note
This notice indicates that there are further issues to be taken into consideration.
Preface
Equipment Manual Control Units and Additional System Components
Equipment Manual, (GH1), 12/2004 Edition, 6SL3097-2AH00-0BP1 vii
Qualified personnel
With reference to this manual and the warning labels on the product, a "qualified person" is
someone who is familiar with the installation, mounting, start-up, and operation of the
equipment and who has certified qualifications for the type of responsibility involved, such
as:
• Trained or authorized to energize, de-energize, ground, and tag circuits and equipment
in accordance with established safety procedures.
• Trained in the proper care and use of protective equipment in accordance with
established safety procedures.
• First aid training.
Finding information
To help you find information more easily, the following sections have been included in the
appendix in addition to the table of contents:
1. References
2. Index
Technical information
Hotline
If you have any further questions, please call our hotline:
A&D Technical Support
Tel.: +49 (0) 180 5050 - 222
Fax: +49 (0) 180 5050 - 223
http.//www.siemens.de/automation/support-request
Please send any questions about the documentation (suggestions for improvement,
corrections, and so on) to the following fax number or e-mail address:
Fax: +49 (0) 9131 98 - 2176
Fax form: See feedback page at the end of this publication
e-mail: [email protected]
Internet address
Up-to-date information about our products can be found on the Internet at the following
address:
http://www.siemens.com/motioncontrol
Preface
Equipment Manual Control Units and Additional System Components
viii Equipment Manual, (GH1), 12/2004 Edition, 6SL3097-2AH00-0BP1
ESD Notices
Caution
Electrostatic sensitive devices (ESDs) are individual components, integrated circuits, or
boards that may be damaged by either electrostatic fields or electrostatic discharge.
Regulations for handling ESD components:
When handling components, make sure that personnel, workplaces, and packaging are well
earthed.
Personnel in ESD areas with conductive flooring may only handle electronic components if:
They are grounded with an ESD wrist band
They are wearing ESD shoes or ESD shoe grounding straps
Electronic boards should only be touched if absolutely necessary. They must only be
handled on the front panel or, in the case of printed circuit boards, at the edge.
Electronic boards must not come into contact with plastics or items of clothing containing
synthetic fibers.
Boards must only be placed on conductive surfaces (work surfaces with ESD surface,
conductive ESD foam, ESD packing bag, ESD transport container).
Do not place boards near display units, monitors, or television sets (minimum distance from
screen: 10 cm).
Measurements must only be taken on boards when:
The measuring instrument is grounded (via protective conductors, for example).
The measuring probe is briefly discharged before measurements are taken with an isolated
measuring device (for example, touching a bare metal housing).
Preface
Equipment Manual Control Units and Additional System Components
Equipment Manual, (GH1), 12/2004 Edition, 6SL3097-2AH00-0BP1 ix
Safety guidelines
Danger
Commissioning shall not start until you have ensured that the machine in which the
components described here are to be installed complies with Directive 98/37/EC.
SINAMICS S equipment must only be commissioned by suitably qualified personnel.
The personnel must take into account the information provided in the technical customer
documentation for the product, and be familiar with and observe the specified danger and
warning notices.
When electrical equipment and motors are operated, the electrical circuits automatically
conduct a dangerous voltage.
Dangerous mechanical movements may occur in the system during operation.
All work on the electrical system must be performed after the system has been switched off
and disconnected from the power supply.
SINAMICS S equipment with three-phase motors may only be connected to the line system
via residual current devices (RCDs) if compatibility of the SINAMICS equipment with the
RCD has been ensured as specified in EN 50178, Subsection 5.2.11.2.
Warning
Correct and safe operation of SINAMICS S equipment assumes correct transportation,
storage, setup, and installation, as well as careful operation and maintenance.
The details in the catalogs and proposals also apply to the design of special equipment
versions.
In addition to the danger and warning information provided in the technical customer
documentation, the applicable national, local, and system-specific regulations and
requirements must be taken into account.
Only protective extra-low voltages (PELVs) that comply with EN60204-1 must be connected
to all connections and terminals between 0 and 48 V.
Preface
Equipment Manual Control Units and Additional System Components
x Equipment Manual, (GH1), 12/2004 Edition, 6SL3097-2AH00-0BP1
Caution
As part of routine tests, SINAMICS equipment with three-phase motors will undergo a
voltage test in accordance with EN 50178. Before the voltage test is performed on the
electrical equipment of industrial machines to EN 60204-1, Section 19.4, all connectors of
SINAMICS equipment must be disconnected/unplugged to prevent the equipment from
being damaged.
Motors must be connected in accordance with the circuit diagram provided. They must not
be connected directly to the three-phase supply because this will damage them.
Note
When operated in dry operating areas, SINAMICS equipment with three-phase motors
conforms to low-voltage Directive 73/23/EEC.
SINAMICS equipment with three-phase motors conforms to EMC Directive 89/336/EEC in
the configurations specified in the associated EC Certificate of Conformity.
Caution
Operating the equipment in the immediate vicinity (< 1.5 m) of mobile telephones with a
transmitter power of > 1 W may lead to incorrect operation.
Andere Handbücher für SINAMICS S120
94
Inhaltsverzeichnis
Andere Siemens Steuereinheit Handbücher
Siemens
Siemens RM-30U Bedienungsanleitung
Siemens
Siemens TM Timer DIDQ Kurzanleitung
Siemens
Siemens 6EP1935-6MC01 Bedienungsanleitung
Siemens
Siemens SINUMERIK 840D sl Kurzanleitung
Siemens
Siemens SiPass Driver Bedienungsanleitung
Siemens
Siemens 6MB5110-1 Bedienungsanleitung
Siemens
Siemens SIRIUS 3TK2834 Bedienungsanleitung
Siemens
Siemens SITOP DC UPS 6EP1931-2DC21 Bedienungsanleitung
Siemens
Siemens RMZ78 Series Bedienungsanleitung
Siemens
Siemens XC10 Series Leitfaden
Siemens
Siemens PM330 Montageanleitung
Siemens
Siemens Simatic S7-1500 Bedienungsanleitung
Siemens
Siemens SINUMERIK 840D sl Stücklistenhandbuch
Siemens
Siemens Simatic Net Scalance M812 Bedienungsanleitung
Siemens
Siemens Simatic S7-1500/ET 200MP Bedienungsanleitung
Siemens
Siemens simovert masterdrives Bedienungsanleitung
Siemens
Siemens MJ-XL Bedienungsanleitung
Siemens
Siemens 3AK Bedienungsanleitung
Siemens
Siemens HTRI-S Bedienungsanleitung
Siemens
Siemens SIRIUS 3RT2 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
