Siemens ValvePAC Series Bedienungsanleitung

KIT INSTALLATION INSTRUCTION

Siemens Industry, Inc.

Kit P/N 16300-1355 15900-378

Kit P/N TGX:16300-1438 Rev. 8

November 2021

ValvePAC™Series 760 Valve Positioner

I/P Transducer Kit

Use this kit to convert a Model 760P pneumatic input valve positioner to a Model 760E that accepts a 4-20 mA input

signal. This kit is also used to replace a failed I/P transducer in a 760E. A copy of SD760, the Series 760 Installation

and Service Instruction, should be available for reference. Refer to SD760 for non-hazardous and hazardous area

installation requirements and for environmental specifications. When installing or servicing in a hazardous area,

refer to Siemens Control Drawing 15032-7602, supplied in SD760.

WARNING

Electrical shock hazard

Explosion hazard

Can cause death, serious injury or property damage

•Remove power from all wires and terminals before working on

equipment.

•In potentially hazardous atmosphere, remove power from equipment

before connecting or disconnecting power, signal, or other circuit.

•Observe all pertinent regulations regarding installation in a hazardous

area.

Kit Parts List

Description

Quantity

Description

Quantity

I/P Transducer

10-32 x 3/8 Slotted Hex Head Screw

I/P Manifold

8-32 x 1/4 Binding Head Screw

O-Ring

8-32 x .375 SL/TX PN TR

Wire Clamp

#8 External Tooth Lockwasher

Clamping Plate

Terminal Washer

10-32 x 2-1/4 Binding Head Screw

Pipe Plug

Installation

Perform the following steps to install the parts in this kit. Note the following when a step is prefaced with a 760

model:

•“760P” - Perform this step when converting a 760P to a 760E.

•“760E” - Perform this step when replacing an I/P transducer in a 760E.

1. Remove all electrical power and process signals from the positioner.

2. Remove supply air from the positioner.

3. Remove the cover by loosening a screw at each corner of the cover and lifting the cover from the positioner.

I/P Transducer Kit 15900-378

November 2021

4. Remove installed parts. Refer to the figure on page 3 as needed.

•760P: Remove the sealing plate screw, sealing plate and two O-rings (the O-rings may adhere to the back

of the sealing plate).

•760E: Disconnect two signal input wires from the I/P transducer. Remove the 10-32 screw securing the

transducer and remove the transducer and I/P manifold. Remove and discard two O-rings from the I/P

manifold and two from recessed seats in the positioner body.

5. Place two new O-rings in the recessed seats in the positioner body and two in the I/P manifold. A very small

amount of O-ring grease

may be applied to the O-rings to assist sealing. Install the manifold and the new I/P

transducer. Fasten with the supplied 10-32 x 2-1/4 screw.

•760P: Go to Step 6.

•760E: Go to Step 10.

6. 760P: To the outside of the positioner near the conduit connection, attach the metal clamping plate with an 8-32

x .375 screw and external tooth lockwasher.

7. 760P: Inside the positioner near the conduit connection, install the 10-32 x 3/8 slotted/hex head ground screw

and terminal washer.

8. 760P: Loosely install the plastic wire clamp and 8-32 x 1/4 binding head screw.

9. 760P: Apply a small amount of non-hardening pipe sealant to the supplied pipe plug. Thread the pipe plug into

the “I” input port. Tighten to 12 ft-lb. (16.3 Nm) maximum.

10. Attach the input leads (recommend 22 AWG shielded, twisted pair wire) to the + and - connections of the I/P

transducer terminal strip. Connect the shield to the ground screw inside the positioner. The wires should enter

the positioner through the conduit connection and be routed through the wire clamp (see the figure). Tighten the

wire clamp mounting screw as needed.

11. Verify I/P operation and positioner calibration. Refer to Section 4 Calibration in SD760.

12. Install the positioner cover, tighten the four screws to 20 in. lbs (2.3 N m), and return the positioner to service.

13. 760P: As needed, attach to the unit an installer supplied label or tag to identify the positioner as a Model 760E.

14. When installing the positioner:

•Connect a ground wire to the external ground screw adjacent to the conduit connection.

•Connect I/P input wires to a 4-20 mA signal source.

•Reconnect items removed in steps 1 and 2.

CAUTION

Make sure that the I/P O-rings are in place and not leaking into the enclosure. If instrument air leaks into the

enclosure to a degree that cannot be properly vented, then pressure will build up inside of the enclosure and if the

leakage is extreme, the cover gasket could be expelled. Before installing the cover, verify that there is no evidence

of air leakage coming from the O-rings (e.g. unusual noise, draft). After the cover is installed, the sound of venting

air emanating from the back of the positioner may indicate the presence of elevated pressure inside the housing. If

this occurs, disconnect external pressure sources and allow the pressure to fully vent before attempting any further

repairs.

15900-378 I/P Transducer Kit

November 2021 3

Customer/Product Support

For support and the location of your local Siemens representative, refer to the table below for the URL of the

Process Instrumentation (PI) portion of the Siemens public Internet site. Once at the site, click Support in the right

column and then Product Support. Next select the type of support desired: sales, technical (see the table below),

documentation, or software.

Online Support Request

http://www.siemens.com/automation/support-request

Technical Support

1-800-333-7421; 8 a.m. to 4:45 p.m. eastern time, Monday through Friday (except

holidays)

Customer Service & Returns

1-800-365-8766 (warranty and non-warranty)

Public Internet Site

http://www.usa.siemens.com/pi

Technical Publications

in PDF

Click the above link to go to the Siemens Internet site and then click Process

Instrumentation. In the column to the right, click Support > Manuals. In the

column to the left, select the product line (e.g. Pressure or Temperature or

Controllers) to open navigation and search panes.

I/P Transducer Kit 15900-378

November 2021

INPUT

LEADS

760-115g

ZERO AND SPAN

ADJUSTMENTS

O-RINGS

I/P MANIFOLD

INPUT

GUAGE

REMOVE SCREW

AND SEALING PLATE -

SAVE O-RINGS

UNDER PLATE

PIPE

PLUG

CLAMPING PLATE, EXTERNAL TOOTH

LOCKWASHER AND 8-32 X .375

SLOTTED SCREW

10-32 x 3/8 SLOTTED

HEX HEAD GROUND

SCREW AND CUPPED

TERMINAL WASHER

WIRE CLAMP

SCREW

8-32 X 1/4 BINDING HEAD

WIRE

CLAMP

I/P TRANSDUCER

MOUNTING SCREW

10-32 X 2-1/2

I/P TRANSDUCER

I/P Transducer Kit

ValvePAC is a trademark of Siemens Industry, Inc. All product designations may be trademarks or product names of Siemens

Industry, Inc. or other supplier companies whose use by third parties for their own purposes could violate the rights of the

owners.

Siemens Industry, Inc. assumes no liability for errors or omissions in this document or for the application and use of information

in this document. The information herein is subject to change without notice.

Procedures in this document have been reviewed for compliance with applicable approval agency requirements and are

considered sound practice. Neither Siemens Industry, Inc. nor these agencies are responsible for product uses not included in the

approval certification(s) or for repairs or modifications made by the user.

◼

DO NOT ADJUST I/P

TRANSDUCER CALIBRATION

SCREWS.

INPUT

GAUGE

I/P Terminals

Left Right

Plus (+) Minus (-)

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP IM 155-6 PN/2 HF Bedienungsanleitung

Siemens

Siemens ASIsafe SIRIUS 3RK1205-0B.00-0AA2 Bedienungsanleitung

Siemens

Siemens CB15 Bedienungsanleitung

Siemens

Siemens CU230P-2 HVAC Bedienungsanleitung

Siemens

Siemens SIMATIC TIM 3V-IE DNP3 Benutzerhandbuch

Siemens

Siemens SIM-16RC Bedienungsanleitung

Siemens

Siemens M3P FY Series Bedienungsanleitung

Siemens

Siemens CP 443-5 Extended Bedienungsanleitung

Siemens

Siemens 3VT9300-4WA30 Bedienungsanleitung

Siemens

Siemens SIDOOR ATD4 W Series Benutzerhandbuch

Siemens

Siemens SINUMERIK 880 SW 6 Technisches Handbuch

Siemens

Siemens SIMADYN D Bedienungsanleitung

Siemens

Siemens OMM-2 Bedienungsanleitung

Siemens

Siemens SINAMICS V60 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840DE SL Kurzanleitung

Siemens

Siemens SMF6120 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SIMATIC S7-1500R/H Bedienungsanleitung

Siemens

Siemens SIRIUS 3RW5 series Technisches Dokument

Siemens

Siemens SIMATIC 8DO DC24V/0.5 A Bedienungsanleitung

Siemens

Siemens 3VL93 Series Bedienungsanleitung

Siemens

Siemens SINAMICS G120 Datenblatt

Siemens

Siemens LMU54 Series Bedienerhandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung