Siemens ICP-B6 Service-Handbuch

To Set the ICP-B6 Module Address:

1. Plug the programming cable of the DPU or

FPI-32 Programmer/Tester (SensorLINK)

into the two-pin receptacle on the ICP-B6.

(See Figure 2 for location only.)

2. Set the system address for the ICP-B6 by

following the instructions in the FPI-32

(SensorLINK) Programmer/Tester Manual,

P/N 315-090077, or the DPU User's

Manual, P/N 315-033260, as applicable.

Removeallsystempowerbeforeinstalla-

tion, first battery and then AC. (To power

up, connect the AC first, then the battery.)

All wiring must comply with

national and local codes.

The ICP-B6 should be installed in a UL

listed electrical box. (See Figure 10.)

Analog Loop

The ICP-B6 communicates with the MXL

through its analog addressable loops. These

loops are on either the MMB or on the op-

tional ALD-2I module of the MOM-4. They

may be wired for Class A (Style 6) or Class B

(Style 4). Figure 1 shows both wiring types

and the connections to either the MMB or to

the MOM-4 when the ALD-2I module is used.

The table on the following page lists the

maximum output currents allowed.

Installation Instructions

MODEL ICP-B6

Intelligent Control Point

The Model ICP-B6 Intelligent Control Point from

Siemens Industry, Inc. can be used as an

independent, remotely located telephone zone, a

speaker zone (25V or 70.7V RMS), or notification

appliance circuit (NAC), depending on how it is

configured. It communicates through the analog

loop of the MXL/MXLV System.

OPERATION

Up to 12 ICP-B6s can connect to each analog

loop of the MXL/MXLV. These modules must

be connected to the first 12 address locations

on the analog loop.

The 24 VDC power input for each ICP-B6

comes from either the MMB, the PSR, or from

an auxiliary power supply which is power

limited and UL listed for fire protective signal-

ing use and is rated between 24 and 27.3

VDC. Each ICP-B6 can be assigned a 32-

character, custom alphanumeric message.

Each module uses one address on either the

analog loop of the ALD-2I module or the analog

loop of the MMB board. (See Figure 1) The

ICP-B6 is programmable for different usages.

For additional information on the MXL/MXLV

System, refer to the MXL/MXLVManual, P/N

315-092036.

Addressing and Testing

Use the DPU Device Programming Unit or the

FPI-32 Programmer/Tester (SensorLINK) to

program and test the module.

NOTE: With FPI-32 Rev. 1.3 software, only

1=MXL mode should be used when

programming a device.

P/N 315-095306-10

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

The ICP-B6 module can be used in four

different ways:

1. Using the ICP-B6 as an NAC Module

This notification appliance application uses the

principle of polarity reversal when there is an

alarm. Figure 2 shows the polarity connection

in a supervisory condition. When using the

ICP-B6 as a supervised NAC output module

with notification appliance devices, cut jumper

JP2. Refer to Figure 2 for additional connec-

tion and jumper information, and to P/N 315-

096363 for a list of compatible devices.

MAXIMUM ALLOWABLE ICP-B6 OUTPUT CIRCUIT LINE RESISTANCE

FOR SPECIFIED DC RISER CURRENT AND LINE RESISTANCE

MAXIMUM

DC RISER

CURRENT

(in Amps)

DC RISER RESISTANCE (in Ohms)

0.1 Ohm 0.25 Ohm 0.5 Ohm 0.75 Ohm 1 Ohm 1.5 Ohms

82.46 1.67 .33 -- -- --

72.53 1.83 .66 -- -- --

62.60 2.00 1.00 -- -- --

52.67 2.16 1.33 .5 -- --

42.73 2.33 1.67 1.00 .33 --

32.80 2.50 2.00 1.50 1.00 --

22.86 2.67 2.33 2.00 1.67 1.00

12.93 2.83 2.67 2.50 2.33 2.00

.5 2.96 2.92 2.83 2.75 2.67 2.50

MAXIMUM LOOP RESISTANCE FOR EACH ICP-B6 ON RISER

NOTES:

1. Resistances specified are for both wires.

2. If higher currents are required, Siemens Industry, Inc. recommends using a local auxiliary

supply which is UL listed for fire protection signaling use. The supply should be rated between

24 and 27.3 VDC.

When used as an NAC module, the output

circuit is power limited. The ICP-B6 maximum

current is 1.5A at 24 VDC. If the 24 VDC is

lost or the NAC line is broken or shorted, the

trouble condition INPUT DEVICE RESPONSE

TOO LOW displays at the MXL/MXLV control

panel. Refer to Figures 3 and 4 for the con-

nections used with the TRI-60/B6 module and

the PSR-1 module, respectively. See the Line

Resistance chart for the allowable line

resistance for each ICP-B6 output circuit.

ELECTRICAL RATINGS

tnerruCeludoMCDV5evitcAAm0

tnerruCeludoMCDV42evitcAAm01

tnerruCeludoMCDV42ybdnatSAm01

Figure 2

ICP-B6 Used as a Strobe Module

POWER

LIMITED

STYLE Y STYLE Z

15K, 1/2W, 5% EOL RESISTOR

P/N 140-820400

15K, 1/2W, 5%

EOL RESISTOR

P/N 140-820400

SUPERVISED STROBE ACTIVATION - SPECIAL APPLICATION

SUPV: 9VDC, .5mA

ACTIVATED: 16-32V UNFILTERED FULL WAVE RECTIFIED, 1.5A MAX

POLARITY SHOWN IN SUPV. CONDITION

ICP-B6 MODULE IS USED FOR

NAC SUPERVISION AND ACTIVATION

NOTES:

1. ALL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.

2. POSITIVE AND NEGATIVE GROUND FAULT DETECTED AT <5K OHMS FOR TERMINALS 3-6.

3. FOR SYNCHRONIZATION OF NOTIFICATION APPLIANCES USE EITHER DSC, DSC-W, OR PAD-3.

ICP-B6 MODULE IS USED FOR

NAC SUPERVISION AND ACTIVATION

16-32 VDC

NAC UNITS

SEE TABLE 1

DC INPUT RATED

24 - 27.3 VDC FWR

SUPV: 12mA

ACTIVATED: 1.5A MAX

24-27.3 VDC, 18mA MAX

9 VDC, 0.5mA

SPECIAL APPLICATION

16-32V UNFILTERED FULL WAVE RECTIFIED

1.5A, POWER LIMITED

ICP-B6 ICP-B6

PROGRAM

PLUG

PROGRAM

PLUG

TB2

TB1 TB1

6 6

5 5

4 4

3 3

2 2

1 1

++++

----

ANALOG

LOOP

CONNECTION

SUPERVISED

MODULE INPUT SUPPLY

FROM PS-35, PSR-1, OR

UL LISTED POWER SUPPLY

MANUFACTURED BY

ALARM-SAF (Model BN4-002-UL)

ELECTRICAL:

INPUT DC SUPPLY:

SUPERVISORY OUTPUT:

ACTIVATED:

JP2 JP2

JP1 JP1

EARTH

SHIELD

TB2

654321

EARTH

SHIELD

Figure 1

Analog Loop Connections

100 OHMS MAX

ANALOG LOOP CONNECTION

(T-TAPPING ALLOWED)

OPERATES IN FULL CONFORMANCE WITH STYLE 4 (CLASS B)

*JUMPERS CAN BE REMOVED FROM MMB-3 WITH CSGM CONFIGURATION

TB1 TB1 TB1

ICP-B6 ICP-B6 ICP-B6

12 12 12

ALD-2I ALD-2I

MOM-4

TB2 MOM-4

TB1 MMB

TB2 MMB

TB3

LOOP 1 LOOP 2 LOOP 1 LOOP 2 LOOP 1 LOOP 2

LOOP RESISTANCE 100 OHMS MAX

18 AWG MINIMUM WIRE

NO EOL DEVICE REQUIRED

SUPERVISED, POWER LIMITED PER NEC 760

ALL WIRING MUST CONFORM TO NATIONAL AND

LOCAL ELECTRICAL CODES

Figure 4

ICP-B6 Connections Using PSR-1

Figure 3

ICP-B6 Connections When Using TRI-60/B6

Using the ICP-B6 as a Telephone Zone

When the ICP-B6 is used as a telephone zone

module, the 24 VDC provides supervision,

trouble, and call-in conditions. If the 24 VDC is

lost, the trouble condition INPUT DEVICE

RESPONSE TOO LOW displays at the MXL/

MXLV and an LED for that zone lights at the

VSM-1 module.

The supervised telephone common talk riser

starts at the TBM module in the MME-3 back-

box. The Class B shielded cable connects

continuously to each ICP-B6 with a 5.6K end of

line device. Tie the shield of these riser wires

and the shield of the zone output wires together

using terminal 5 of TB2 and isolate them from

the system circuits and the earth ground.

Connect the supervised individual zone output

connections from each ICP-B6 to the field

telephone with shielded cable. Terminate

them at the last station with a 10K ohm end of

line resistor. As with the common talk line

described in the paragraph above, be sure

that the shield is continuous and isolated

Figure 5

ICP-B6 Used as a Telephone Zone

ANALOG LOOP

CONNECTION

FJ-303

BLACK

BLACK BLACK

BLACK

WHITE WHITE WHITE WHITE

SHIELD

WARDEN'S STATIONS

MODELS FT-301 SERIES

AND FT-302 SERIES

24 OHMS MAX

10K, 1/2W, +/-5%

EOL RESISTOR

P/N 140-112172

AT LAST STATION

ICP-B6 DC SUPPLY

FROM MMB, PSR-1, OR

UL LISTED POWER SUPPLY

MANUFACTURED BY ALARM-SAF

Model BN4-002-UL (SUPERVISED)

FROM PREVIOUS ICP-B6, OCC-1,

OR TBM

(20 OHMS MAXIMUM

LINE RESISTANCE)

COMMON TALK RISER

18 AWG MINUMUM

BELDON 8760 OR EQUIVALENT

OR AS REQUIRED BY

THE LOCAL AUTHORITY

HAVING JURISDICTION

RISER

NOMINAL VOLTAGE:

MAXIMUM CURRENT:

17.5 VDC

175 mA

10K, 1/2W, +/-5%

EOL RESISTOR

P/N 140-112172

AT LAST FJ-303

5.6K, 1/2W, +/-5%

EOL RESISTOR

ELECTRICAL:

INPUT DC SUPPLY:

SUPERVISORY OUTPUT:

ACTIVATED OUTPUT:

20.5 TO 30 VDC, 18mA MAX

8V, .8mA

11V, 70mA

SUPERVISED

POWER LIMITED

FROM MXL MMB OR

ALD-2I ON MOM-4

(12 MAX ICP-B6

MODULES PER LOOP)

(SUPERVISED)

NOTES:

1. THE SHIELD ON THE COMMON TALK LINE MUST BE CONTINUOUS

AND CONNECTED ONLY TO DC COMMON AT CONTROL PANEL.

2. ALL WIRING MUST CONFORM TO NATIONAL AND LOCAL CODES.

3. POSITIVE AND NEGATIVE GROUND FAULT DETECTED AT <5K OHMS FOR TERMINALS 3-6.

ICP-B6 ICP-B6

PROGRAM

PLUG

PROGRAM

PLUG

TB1 TB1

6 6

5 5

4 4

3 3

2 2

1 1

++++

----

JP2 JP2

JP1 JP1

SHIELD SHIELD SHIELD

SHIELD

TB2

654321

SHIELD

EARTH

TB2

654321

SHIELD

EARTH

from both system circuits and earth

ground and that the shields are connected

together using terminal 5 of TB-2.

3. Using the ICP-B6 as a 70 Volt Speaker

Zone

When the ICP-B6 is used as a speaker zone,

the 24 VDC provides the supervision. If the 24

volts is lost or there is an open or shorted

speaker output line, the trouble condition

INPUT DEVICE RESPONSE TOO LOW

displays at the MXL/MXLV and the related

zone LED on the VSM-1 lights.

The 70.7V RMS audio input comes from the

amplifier via the ASC-2 Amplifier Supervision

card. The ASC-2 supervises the audio con-

nection path to the ICP-B6 and provides up to

100 watts of power. The ASC-2 can be used

as Style Y (Class B) or Style Z (Class A). Refer

to the ASC-2 Instructions, P/N 315-092085.

When the ICP-B6 is used as a speaker zone,

the output speaker lines are supervised and

power limited. The audio output cannot exceed

25 watts. Connect the speaker output as either

Style Y (Class B) or Style Z (Class A). Figure 6

gives the approximate decibel loss for the total

speaker zone wire length for various wire

gauge sizes.

When using the ICP-B6 as a 70.7V RMS

speaker zone, cut the JP1 jumper. (See

Figure 8.)

4. Using the ICP-B6 as a 25 Volt Speaker

Zone

When the ICP-B6 is used as a speaker zone,

the 24 VDC provides the supervision. If the 24

volts is lost or there is an open or shorted

speaker output line, the trouble condition

INPUT DEVICE RESPONSE TOO LOW

displays at the MXL/MXLV and the related

zone LED on the VSM-1 lights.

The 25V RMS audio input comes from the

amplifier via the ASC-2 Amplifier Supervision

card. The ASC-2 supervises the audio con-

nection path to the ICP-B6 and provides up to

100 watts of power. The ASC-2 can be used

as Style Y (Class B) or Style Z (Class A).

Refer to the ASC-2 Instructions, P/N 315-

092085.

When the ICP-B6 is used as a speaker zone,

the output speaker lines are supervised and

power limited. The audio output cannot

exceed 35 watts. Connect the speaker output

as either Style Y (Class B) or Style Z (Class

A). Figure 7 gives the approximate decibel

loss for the total speaker zone wire length for

various wire gauge sizes.

When using the ICP-B6 as a 25V RMS

speaker zone, cut the JP2 jumper (See

Figure 9).

Figure 6

Approximate Speaker Zone Wire Loss

with the 70.7V Option

Figure 7

Approximate Speaker Zone Wire Loss

with the 25V Option

ASC-2

15K, 1/2W, 5%

EOL RESISTOR

P/N 140-820400

15K, 1/2W, +/-5%

EOL RESISTOR

P/N 140-820400

15K, 1/2W, 5%

EOL RESISTOR

P/N 140-820400

STYLE Z

SUPERVISED

SPEAKER ZONE CONNECTIONS

SUPV: 9 VDC, 0.5 mA

ACTIVATED: 70.7 VRMS, 25 W MAX

STYLE Y

SUPERVISED

SPEAKER ZONE CONNECTIONS

SUPV: 9 VDC, 0.5 mA

ACTIVATED: 70.7 VRMS, 25 W MAX

+++

-- -

24K, 1/2 W, +/-5%

EOL RESISTOR

ON LAST ICP-B6

SPEAKER ZONE

MODULE

P/N 140-820405

24K, 1/2 W, +/-5%

EOL RESISTOR

P/N 140-820405

ORIGINAL NFPA STYLE Z

AUDIO RISER CONNECTIONS

TO ICP-B6 ZONE MODULES

FIRST ICP-B6 LAST ICP-B6

ASC-2 RISER CAN NOT

BE T-TAPPED

70.7 VRMS SPEAKER UNITS:

ANY UL LISTED FIRE

PROTECTION SIGNALING

SPEAKER RATED 70.7 V

IS COMPATIBLE WITH

THIS CIRCUIT

10 OHMS MAX

CAPACITOR

COUPLED

70.7 VRMS

SPEAKERS

SUPERVISED BY ICP-B6 MODULES

SUPERVISED

RISER

OBSERVE

CONNECTION

POLARITY

NFPA STYLE Y

AUDIO RISER CONNECTIONS

SUPERVISORY: 9 VDC, 0.5mA

AUDIO OUTPUT: 70.7 VRMS,

100 WATTS MAX

SHIELD

100 OHMS MAX

MAXIMUM OF 12 ICP-B6

MODULES PER LOOP

SEE MXL MANUAL

(P/N 315-092036)

SUPERVISED ANALOG

LOOP CONNECTION

FROM MXL, MMB,

OR ALD-2I ON MOM-4

JP1 JP1

ICP-B6

PROGRAM

PLUG

TB1

JP2

JP1

ICP-B6

PROGRAM

PLUG

TB1

JP2

JP1

ICP-B6

PROGRAM

PLUG

TB1

JP2

JP1

All wiring must comply with national and local codes.

ELECTRICAL:

INPUT DC SUPPLY:

SUPERVISORY OUTPUT:

ACTIVATED OUTPUT:

24-27.3 VDC, 18mA MAX

9 VDC MAX, 0.5mA

70.7 V, 25 WATTS MAX

ICP-B6 DC SUPPLY FROM MMB, PSR-1,

OR UL LISTED POWER SUPPLY

MANUFACTURED BY ALARM-SAF

(Model BN4-002-UL)

DC INPUT RATING

24-27.3 VDC, 18 mA

TB2 654321

SHIELD

EARTH

TB2 654321

SHIELD

EARTH

TB2 654321

SHIELD

EARTH

TB2 654321

SHIELD

EARTH

TB2 654321

SHIELD

EARTH

ASC-2

15K, 1/2W, 5%

EOL RESISTOR

P/N 140-820400

15K, 1/2W, +/-5%

EOL RESISTOR

P/N 140-820400

15K, 1/2W, 5%

EOL RESISTOR

P/N 140-820400

STYLE Z

SUPERVISED

SPEAKER ZONE CONNECTIONS

SUPV: 9 VDC, 0.5 mA

ACTIVATED: 25 VRMS, 35 W MAX

STYLE Y

SUPERVISED

SPEAKER ZONE CONNECTIONS

SUPV: 9 VDC, 0.5 mA

ACTIVATED: 25 VRMS, 35 W MAX

+++

-- -

24K, 1/2 W, +/-5%

EOL RESISTOR

ON LAST ICP-B6

SPEAKER ZONE

MODULE

P/N 140-820405

24K, 1/2 W, +/-5%

EOL RESISTOR

P/N 140-820405

ORIGINAL NFPA STYLE Z

AUDIO RISER CONNECTIONS

TO ICP-B6 ZONE MODULES

FIRST ICP-B6 LAST ICP-B6

ASC-2 RISER CAN NOT

BE T-TAPPED

25 VRMS SPEAKER UNITS:

ANY UL LISTED FIRE

PROTECTION SIGNALING

SPEAKER RATED 25 V

IS COMPATIBLE WITH

THIS CIRCUIT

10 OHMS MAX

CAPACITOR

COUPLED

25 VRMS

SPEAKERS

SUPERVISED BY ICP-B6 MODULES

SUPERVISED

RISER

OBSERVE

CONNECTION

POLARITY

NFPA STYLE Y

AUDIO RISER CONNECTIONS

SUPERVISORY: 9 VDC, 0.5mA

AUDIO OUTPUT: 25 VRMS,

100 WATTS MAX

SHIELD

100 OHMS MAX

MAXIMUM OF 12 ICP-B6

MODULES PER LOOP

SEE MXL MANUAL

(P/N 315-092036)

SUPERVISED ANALOG

LOOP CONNECTION

FROM MXL, MMB,

OR ALD-2I ON MOM-4

JP1 JP1

ICP-B6

PROGRAM

PLUG

TB1 6

JP2

JP1

ICP-B6

PROGRAM

PLUG

TB1 6

JP2

JP1

ICP-B6

PROGRAM

PLUG

TB1 6

JP2

JP1

All wiring must comply with national and local codes.

ELECTRICAL:

INPUT DC SUPPLY:

SUPERVISORY OUTPUT:

ACTIVATED OUTPUT:

24-27.3 VDC, 18mA MAX

9 VDC MAX, 0.5mA MAX

25 V, 35 WATTS MAX

ICP-B6 DC SUPPLY FROM MMB, PSR-1,

OR UL LISTED POWER SUPPLY

MANUFACTURED BY ALARM-SAF

(Model BN4-002-UL)

DC INPUT RATING

24-27.3 VDC, 12 mA

TB2

654321

SHIELD

EARTH

TB2

654321

SHIELD

EARTH

TB2

654321

SHIELD

EARTH

TB2

654321

SHIELD

EARTH

TB2

654321

SHIELD

EARTH

Figure 8

ICP-B6 Used as a 70.7V Speaker Zone

Figure 9

ICP-B6 Used as a 25V Speaker Zone

MOUNTING

(See Figure 10)

1. Use a standard 3 1/2-inch deep, double

gang electrical switchbox or a 4-inch

square electrical box that is 2 1/2inches

deep with either a 1 1/2-inch deep

extension or a 1 1/4 -inch deep plaster ring

extension.

2. Connect the field wiring. Insert the ICP-B6

into the box and fasten the module plate

to the box.

Figure 10

Mounting the ICP-B6

NOTE: When using the double gang

switchbox or the plaster ring

extension, use the same four

screws to fasten both the mod-

ule and the blank plate (user

supplied).

3. Cover the module front plate with a 4-inch

blank plate (user supplied) and fasten

with two plate screws.

P/N 315-095306-10

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens SIMATIC S7-1200 CP 1243-8 IRC Benutzerhandbuch

Siemens

Siemens LCM-OAVS 570-804PA Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens Desigo RXC20.1 Bedienungsanleitung

Siemens

Siemens BACnet ATEC Bedienungsanleitung

Siemens

Siemens PXC00-U Bedienungsanleitung

Siemens

Siemens ECOFAST 3RK1323 Series Bedienungsanleitung

Siemens

Siemens Simatic S7-1500R Bedienungsanleitung

Siemens

Siemens scalance WLC711 Betriebsanleitung

Siemens

Siemens RDU340 Series Bedienerhandbuch

Siemens

Siemens 540-716 Service-Handbuch

Siemens

Siemens 8MR2170 Bedienungsanleitung

Siemens

Siemens SQK349.00/209 Bedienungsanleitung

Siemens

Siemens RAJA+ Leitfaden

Siemens

Siemens SIPART Series Bedienungsanleitung

Siemens

Siemens GAMMA instabus UP 204 Service-Handbuch

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMOCODE pro Benutzerhandbuch

Siemens

Siemens SIMOTION Series Bedienungsanleitung

Siemens

Siemens SFA21/18 Bedienungsanleitung

Siemens

Siemens GEB 1 Series Bedienungsanleitung

Siemens

Siemens Sirius 3RA6 Benutzerhandbuch

Siemens

Siemens OpenAir GCA Series Betriebsanleitung

Siemens

Siemens OpenAir GEB 131.1E Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung