Siemens SITRANS S7-300 Bedienungsanleitung

SITRANS

Configuring a SmartLinx ready

device with a PROFIBUS DP card in

a S7-300 or S7-400 PLC

Application examples

08\2020

AG060425

Introduction

Overview

Planning/configuring

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

Document order number: AG060425

Ⓟ08/2020 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Configuring a SmartLinx ready device with a PROFIBUS DP card in a S7-300 or S7-400 PLC

Application examples, 08\2020, AG060425 3

Table of contents

1 Introduction ........................................................................................................................................... 4

1.1 Objective ............................................................................................................................. 4

1.2 Equipment........................................................................................................................... 4

1.3 Disclaimer............................................................................................................................ 4

2 Overview................................................................................................................................................ 5

3 Planning/configuring ............................................................................................................................. 6

3.1 Required steps ..................................................................................................................... 6

Configuring a SmartLinx ready device with a PROFIBUS DP card in a S7-300 or S7-400 PLC

4Application examples, 08\2020, AG060425

1Introduction

1.1 Objective

The objective of this application guide is to help the user become familiar with the steps

required to configure a SmartLinx device in Step 7.

1.2 Equipment

Equipment

Article No.

SITRANS instrument

.gsd file

SIMATIC STEP 7 ver. 5.2 (SP. 1)

MPI/PROFIBUS Interface to PLC

Terminal screwdriver

PC or Laptop

1.3 Disclaimer

Note

While every effort is made to verify the following information, no warranty of accuracy or

usability is expressed or implied.

Configuring a SmartLinx ready device with a PROFIBUS DP card in a S7-300 or S7-400 PLC

5Application examples, 08\2020, AG060425

2Overview

SIMATIC STEP 7 is the Siemens programming software used to set up a S7-300 or S7-400 PLC.

This Application Guide discusses the following:

•Running Hardware Config. to set up a network

•When and how to import a .gsd file

•How to view the data

Please note that the configuration of a MultiRanger 100 on a S7-400 PLC is for illustration

purposes only. The process is similar for all applicable Siemens SmartLinx-ready products.

Configuring a SmartLinx ready device with a PROFIBUS DP card in a S7-300 or S7-400 PLC

6Application examples, 08\2020, AG060425

3Planning/configuring

3.1 Required steps

Step 1 - Locating the .gsd file.

The .gsd file for SmartLinx is located on the support disk that is shipped with the SmartLinx

card. You can also download this support disk from the SmartLinx product page which can be

navigated to from www.siemens.com/processautomation.

The .gsd file is located on the support disk in the \GSD directory. There are two different .gsd

files depending on the product:

•for AiRanger or SITRANS LU products, use hms-1002.gsd

•for all other products, use hms1003.gsd

Step 2 - Getting into Hardware Config

Hardware Config is the part of STEP 7 and PCS 7, both used for configuring the network. To

operate it, first run SIMATIC Manager and then open a project.

1. Using the left side of the screen, navigate to a position similar to the screen shot below:

2. Double-click the Hardware icon in the right window of the screen.

Planning/configuring

3.1 Required steps

Configuring a SmartLinx ready device with a PROFIBUS DP card in a S7-300 or S7-400 PLC

Application examples, 08\2020, AG060425 7

Step 3 - Importing the GSD file into STEP 7

1. From within Hardware Config, click Options/Install New GSD ….

2. If this error messages appears, close the open hardware project by clicking Station/close on

the navigation bar.

Planning/configuring

3.1 Required steps

Configuring a SmartLinx ready device with a PROFIBUS DP card in a S7-300 or S7-400 PLC

8Application examples, 08\2020, AG060425

3. Repeat Step 1 to import the .gsd file and navigate to the .gsd file.

4. In this example, the MultiRanger .gsd file (hms1003.gsd) is selected.

5. Select Open on the Installation box to install the .gsd file.

Planning/configuring

3.1 Required steps

Configuring a SmartLinx ready device with a PROFIBUS DP card in a S7-300 or S7-400 PLC

Application examples, 08\2020, AG060425 9

Step 4 - Adding the device to the network

1. Open the Hardware catalog by clicking on the third icon from the right (mouse-over will

verify).

2. The .gsd file for the MultiRanger is located in /PROFIBUS DP/Additional Field

Devices/General/ ANYBUS S PDP.

Note

•Please note that the MultiRanger file is ANYBUS-S PDP.

•For the AiRanger or SITRANS LU instruments, the .gsd is in the same location, but is

called AB-DT-PDP.

3. Highlight the PROFIBUS DP network where the MultiRanger is going.

Planning/configuring

3.1 Required steps

Configuring a SmartLinx ready device with a PROFIBUS DP card in a S7-300 or S7-400 PLC

10 Application examples, 08\2020, AG060425

4. Highlight ANYBUS-S PDP and drag it to the required PROFIBUS DP network. Dragging it into

the network, opens the Properties Interface box.

Note

Note that the address of the MultiRanger on the PROFIBUS DP network must be known.

5. Place the MultiRanger address at Address 4. (Lab demo only)

6. Highlight the selected PROFIBUS DP network, and then click OK on the Properties dialog

box.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens FC18 Series Bedienungsanleitung

Siemens

Siemens RWD68 Bedienungsanleitung

Siemens

Siemens N 567/01 Bedienungsanleitung

Siemens

Siemens SSA911.01ZB Bedienungsanleitung

Siemens

Siemens Gamma instabus UP204 Contouch Service-Handbuch

Siemens

Siemens RWD32S Bedienungsanleitung

Siemens

Siemens Types NRK 16-T../A Bedienungsanleitung

Siemens

Siemens RWD68U Betriebsanleitung

Siemens

Siemens Simatic S7-300 Bedienungsanleitung

Siemens

Siemens Acvatix G B111.9E/MO Series Bedienungsanleitung

Siemens

Siemens 550-506 Bedienungsanleitung

Siemens

Siemens GGA 1E Series Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens GEB 1 Series Bedienungsanleitung

Siemens

Siemens simovert masterdrives Bedienungsanleitung

Siemens

Siemens RAJA+ 3TE7 DOL Leitfaden

Siemens

Siemens Acvatix SSC31 Bedienungsanleitung

Siemens

Siemens SEZ50MB Bedienungsanleitung

Siemens

Siemens XC1003-A Bedienungsanleitung

Siemens

Siemens RDX33.21 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500/ET 200MP Benutzerhandbuch

Siemens

Siemens Desigo PXC4.M16 Bedienungsanleitung

Siemens

Siemens GIB 1 Series Bedienungsanleitung

Siemens

Siemens RRV851 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung