Siemens OpenAir GDE131.1U Bedienungsanleitung

Installation Instructions

Document No. 129-367

September 1, 2003

OpenAir™ Electronic Damper Actuator

GDE/GLB Rotary Non-spring Return

EA0678R3

a. Actuator

b. Position indicator

c. Mounting bracket

d. Mounting screws

e. 4 mm hex key

f. Shaft insert for use with

3/8-inch (8-10 mm) shafts

Figure 1. Parts of the GDE/GLB Rotary Actuator.

Product Description

Steps for direct-coupled mounting of the OpenAir

GDE/GLB Series non-spring return rotary electronic

damper actuator.

Product Numbers

GDE131.1U GLB131.1P

GDE131.1U/B (24 pk) GLB132.1P

GDE131.1P GLB136.1P

GDE131.1P/B (24 pk) GLB161.1P

GDE131.1Q/B 6-ft cable (12 pk) GLB163.1P

GDE132.1P GLB164.1P

GDE136.1P GLB166.1P

GDE161.1P

GDE161.1P/B (24 pk)

GDE163.1P

GDE164.1P

GDE166.1P

Required Tools

• 4 mm hex wrench

• 4 mm (5/32-inch) drill bit and drill

• Small flat-blade screwdriver

• Marker or pencil

Estimated Installation Time

30 minutes

Warning/Caution Notations

WARNING

Personal injury/loss of life may

occur if you do not follow a

procedure as specified.

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow a procedure as

specified.

Instructions

WARNING:

Do not open the actuator.

NOTE: Place the actuator on the damper shaft so

that the front of the actuator is accessible.

The label is on the front side.

1. Determine whether the damper blades will rotate

clockwise or counterclockwise to open. See

Figure 2.

2. If the blades will rotate counterclockwise, slide the

manual override switch to manual, and move the

adjustment lever to the right. Return the switch to

automatic. See Figure 9.

To mount a (modulating) GDE/GLB16x, set the Dual

In-line Package (DIP) switches to the required

positions.

1. To access the DIP switches, raise the tab on the

lower left side of the actuator. See Figure 2. The

factory setting is clockwise (middle switch), with a

direct-acting feedback signal (right switch).

2. Close the tab over the DIPswitches.

To mount a (3-positon) GDE/GLB13x for counter-

clockwise rotation, follow the Counterclockwise

Damper Rotation instructions located in the Wiring

Diagrams section when wiring the actuator to the

controller.

Item Number: 129-367, Rev. 010 Page 1 of 6

Document No. 129-367

Installation Instructions

September 1, 2003

2’

3’

only for:

GDE16...1P

GLB16...1P

MODULATING

only for:

GDE16...1P

GLB16...1P

MODULATING

"0"

self adapt

selfadapt

CLOCKWISE

TO OPEN

COUNTER

CLOCKWISE

TO OPEN

EA0680R2

self adapt

selfadapt

Figure 2. Setting the Direction of Rotation.

NOTE: For DIP switch setting options, see the

Technical Instructions EA GDE/GLB-1

(155-187P25).

Mounting and Installation

NOTE: The GDE/GLB actuator comes with a factory

installed 1/2-inch shaft guide. If shaft size is

1/2-inch, proceed with Figure 6.

When using a 3/8-inch shaft: Remove factory installed

1/2-inch guide. See Figure 3.

EA0999R1

Figure 3. Removing 1/2-inch Ø shaft

guide for 3/8-in or 5/8-in shaft.

EA0679R3

Mounting GDE/GLB on

3/8-inch

8...10 mm shafts

Figure 4. 3/8 Ø inch shaft, see Figure 1 Item f.

1. A 3/8-inch shaft adapter is provided in

actuator package.

2. Hold the shaft insert so that the raised tabs

are inserted last when placing the insert into

the back of the actuator.

3. Proceed to Figure 6.

When using a 5/8-inch shaft:

EA01001R2

Figure 5. 5/8 Ø inch shaft.

1. Remove factory installed 1/2-inch guide. See

Figure 3.

2. Mount actuator to shaft per Figure 6.

EA0532R2

Figure 6. Mounting Actuator to Damper Shaft.

EA0533R3

4 mm

60-90 lb-in

(7-10 Nm)

Torque

Figure 7. Installing the Position Indicator (b).

Page 2 of 6 Siemens Building Technologies, Inc.

Document No. 129-367

Installation Instructions

September 1, 2003

EA0786R4

1/2

CENTER THE

MOUNTING BRACKET

IN THE SLOT

CAUTION:

THESE HOLES FOR USE WITH

ACCESSORY KITS ONLY. DO NOT

USE IN THE INSTALLATION OF

DIRECT-COUPLED APPLICATIONS

∅4 mm

5/32 in.

Figure 8. Attaching the Mounting Bracket.

Manual Override

To move the damper blades and lock the position with

no power present, do the following:

1. Slide the red manual override knob toward the

back of the actuator. See figure 9.

2. Make adjustments to the damper position.

3. Slide the red manual override knob toward the

front of the actuator.

Once power is restored, the actuator returns to

automated control.

PL0013R2

MANUAL

ADJUSTMENT

LEVER

AUTO

Figure 9. Manual Override.

Dual Auxiliary Switch Setting

For GDE/GLB 136x, GDE/GLB164x and

GDE/GLB166x only.

Factory setting: A = 5° B = 85°

Use a flat-blade screwdriver to adjust the A switch.

The long arm of the †points to the setting. Manually

turn the red ring of the B switch. The narrower tab on

the ring points to the setting. See Figure 10.

The auxiliary switch setting shafts rotate with the

actuator.

NOTE: The scale is valid only when the actuator is in

the "0" position on clockwise motion.

80 70 60

2010

AUX SWITCH

ADJUSTMENT

EA0636R2

Figure 10. Auxiliary Switch Setting Dial.

Mechanical Range Adjustment

EA0535R2

4 mm

45¡

90¡

A0536R2

<90¡

Figure 11. Moving the Mechanical Range Stop.

1. Loosen the stop set screw.

2. Move it along the track to the desired position, and

fasten it in place.

Mechanical Range Limitation and

Self–adapt Feature

1. To use the entire 0 to 10V input signal to control

the adjusted range, raise the tab located on the

lower left-hand side of the actuator and locate the

DIP switches. See Figure 12.

2. Set the self-adapt DIP switch to (ON).

3. Close the tab over the DIP switches.

For example, if you set the locking screw at 70° and

turn the self-adapt switch ON, a 5V input signal will

drive the damper to 35° (50% of its adjusted range).

Siemens Building Technologies, Inc. Page 3 of 6

Document No. 129-367

Installation Instructions

September 1, 2003

self adapt

EA0621R1

Figure 12. Self-adapt Switch in the On Position.

Factory setting 0 (OFF)

CAUTION:

When turning the self-adaptive feature on, or

after software reset with the feature on, the

actuator will enter a five-minute calibration cycle

as the actuator adjusts to the rotation limits of

the system. The software reset happens after

power on, or may be caused by electrostatic

discharge (ESD) at levels of 2 kV and above.

Slope (span) and Offset adjustment

For GDE/GLB163x and GDE/GLB164x only

Factory setting:

Slope (span) ∆U ≈10

Offset Uo = 0

Use a flat-blade screwdriver to

make adjustments. The long arm of

the †points to the setting.

EA0633R2

SLOPE,

OFFSET,

Figure 13.

Wiring

All wiring must conform to NEC and local codes and

regulations.

Use earth ground isolating step-down Class 2

transformers. Do not use autotransformers.

Determine the supply transformer rating by summing

total VA of all actuators used. It is recommended that

one transformer power no more than 10 actuators.

WARNING:

Installations requiring Conformance

• All wiring for CE rated actuators must only

be separated extra low voltage (SELV) or

protective extra low voltage (PELV) per

HD384-4-41.

• Use safety-isolating transformers (Class

III transformer) per EN 61558. They must

be rated for 100% duty cycle.

• Overcurrent protection for supply lines is

maximum 10A.

Wiring Diagrams

GDE/GLB13x

Counterclockwise Damper Rotation of GDE/GLB13x

If the damper blades turn counterclockwise to open (CCW),

reverse the 6 (violet) and 7 (orange) wires at the controller.

CAUTION:

Do not wire different types of actuators (such as

GBB or GIB actuators) in parallel with these

models.

Page 4 of 6 Siemens Building Technologies, Inc.

Document No. 129-367

Installation Instructions

September 1, 2003

Table 1. 3-position Control 24 Vac.

Color

Standard

Symbol Function Terminal

Designation Standard Plenum

1 Supply (SP) G Red Red

6 Control signal clockwise Y1 Violet Violet

7 Control signal

counterclockwise

Y2 Orange Orange

Factory installed options

S1 Switch A Common Q11 Gray/red Black

S2 Switch A N.C. Q12 Gray/blue Black

S3 Switch A N.O. Q14 Gray/pink Black

S4 Switch B Common Q21 Black/red Black

S5 Switch B N.C. Q22 Black/blue Black

S6 Switch B N.O. Q24 Black/pink Black

P1 Feedback Potentiometer

0 to 100% P1 - P2

a White/red Black

P2 Feedback Potentiometer

Common

b White/blue Black

P3 Feedback Potentiometer

100 to 0% P3 - P2

c White/pink Black

GDE/GLB13x, Continued

24 Vac power supply 3-position control.

Each wire has the standard symbol printed

on it. See Table 1.

MAB

1000

P1 P3P2 S1 S4

S2 S3 S5 S6

EA0282R1

EA0635R2

Vac

EARTH GROUND

ISOLATING CLASS 2

TRANSFORMER FOR

24Vac POWER

: SAFETY ISOLATING

TRANSFORMER

PER EN 60742

120Vac

7 (ORANGE)

6 (VIOLET)

1 (RED)

NEUT

Figure 14. 3-position Control.

GDE/GLB16x

24 Vac power supply 0 to 10V modulating

control

Each wire has the standard symbol printed

on it. See Table 2.

MAB

S1 S4

S2 S3 S5 S6

EA0284R1

Figure 15. 0 to 10V Modulating Control.

Table 2. Modulating Control.

Standard

Symbol Function Terminal

Designation Color

1 Supply (SP) G Red

2 Neutral (SN) G0 Black

8 0 to 10V input signal Y Gray

9 Output for 0 to 10 Vdc

position indication

U Pink

Factory installed options

S1 Switch A – Common Q11 Black

S2 Switch A – N.C. Q12 Black

S3 Switch A – N.O. Q14 Black

S4 Switch B – Common Q21 Black

S5 Switch B – N.C. Q22 Black

S6 Switch B – N.O. Q24 Black

Siemens Building Technologies, Inc. Page 5 of 6

Document No. 129-367

Installation Instructions

September 1, 2003

Dimensions

2-3/4

(70)

5/32

(4)

13/16

(21)

3-7/16

(87)

5-7/16

(137)

15/16

(94)

7/16

(11)

min. 4 inch

100 mm

2-3/8

(60)

1/32

(0.8)

EA0530R3

min. 1/4 inch

6 mm min. 8 inch

200 mm

min. 3/8 inch

10 mm

min. 1 inch

25 mm

min. 2-3/8 inch

60 mm

6-5/8

(168) 7-1/16

(180)

EA0531R2

1/2

(12) 25/32

(20)

Figure 16. Dimensions of the OpenAir GDE/GLB Actuator and Mounting Bracket.

References

EA GDE/GLB-1 155-187P25

OpenAirElectronic Damper Actuators

GDE/GLB Series Non-spring Return Rotary

24 Vac Modulating Control

EA GDE/GLB-2 155-188P25

OpenAirElectronic Damper Actuators

GDE/GLB Series Non-spring Return Rotary

24 Vac Three-Position Control

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as

design improvements are introduced. OpenAir is a trademark of Siemens Building Technologies, Inc. Other product or company names mentioned

Siemens Building Technologies, Inc.

1000 Deerfield Parkway

Your feedback is important to us. If you have

comments about this document, please send

Buffalo Grove, IL 60089-4513

U.S.A.

them to [email protected]

Page 6 of 6

Document No. 129-367

Printed in the U.S.A.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens RVL481 Bedienerhandbuch

Siemens

Siemens SIMOTION C230-2 Technisches Dokument

Siemens

Siemens REA23M Bedienungsanleitung

Siemens

Siemens 3VA9677-0EK11 Bedienungsanleitung

Siemens

Siemens SIMODRIVE 611U Bedienungsanleitung

Siemens

Siemens Simatic S7 Series Benutzerhandbuch

Siemens

Siemens N 545D31 Bedienungsanleitung

Siemens

Siemens Delta Series Bedienungsanleitung

Siemens

Siemens SIRIUS ET 200S Bedienungsanleitung

Siemens

Siemens GEB-1E Series Bedienungsanleitung

Siemens

Siemens SIMATIC S5 Series Bedienungsanleitung

Siemens

Siemens SIRIUS 3RW44 2 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 840 Technisches Handbuch

Siemens

Siemens SIRIUS 3RW50 Bedienungsanleitung

Siemens

Siemens SIMOTION C Bedienungsanleitung

Siemens

Siemens Climatix HMI-TM Bedienerhandbuch

Siemens

Siemens DXR2.E10PL-102B Bedienungsanleitung

Siemens

Siemens SIPLUS HCS CIM4210C PROFINET Administratorhandbuch

Siemens

Siemens SINUMERIK 828D Turning Kurzanleitung

Siemens

Siemens SIPART DR22 Bedienungsanleitung

Siemens

Siemens SSD31 Series Bedienungsanleitung

Siemens

Siemens LMV60.110A2 Bedienungsanleitung

Siemens

Siemens DOL Series Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung