Siemens SSB161.05U Bedienungsanleitung

Electromotoric actuator

SSB161.05U

For Powermite MZ Series 2-way and 3-way globe valves

●Operating voltage AC/DC 24 V, positioning signal DC 0...10 V

●Self-calibrating to the valve stroke

●Direct mounting with coupling nut, no tools required

●Manually override

●Position and actuator motion indication (LED)

●Positioning force 45 lbf (200 N)

●Parallel operation of multiple actuators possible

A6V12681516_enUS_a Smart Infrastructure

10/12/2022

Siemens A6V12681516_enUS_a

Smart Infrastructure 10/12/2022

Use

●For 2-way and 3-way Powermite 599 MZ Series globe valves, 599-01100 - 599-01139

●Typically in chilled ceiling, VAV, unit ventilators, fan coil unit and other terminal unit ap-

plications

●Max.10 units of SSB161.05U can operate in parallel, provided the controller output

suffices.

Technical design When the actuator is driven by DC 0…10 V positioning signal, it produces a stroke, which is

transmitted to the valve stem. This is converted to mechanical stroke which controls the

position of valve stem.

If not specifically stated, the description of operation in this document applies to valve

versions that are fully closed when valve stem is extended / no actuator is mounted.

DC 0...10 V control signal

●The valve opens / closes in proportion to the

control signal at Y.

●At DC 0 V, the actuator stem is retracted, the

normally closed valve is fully closed and the

normally open valve is fully open.

●When no power is supplied, the actuator maintains

its current position.

Y = Control signal Y [V]

H = Percentage of calibrated valve stroke

LED indication

Status LED indication patterns

Variants SSB161.05U

Modulation: Stem retracting Flashing green in sequence: LED1-->LED2-->LED3

(500 ms each)

Modulation: Stem extending Flashing green in sequence: LED3-->LED2-->LED1

(500 ms each)

Stem position At H0 (fully retracted) - H40: Constant green (LED1)

At H40 - H60: Constant green (LED 2)

At H60 - H100 (fully extended): Constant green (LED3)

Calibration Flashing green (LED2): 100 ms on, 100 ms off

Error Constant red (LED2)

Manual operation Flashing green/red alternatively (LED2): Green 500 ms,

red 500 ms

Siemens A6V12681516_enUS_a

Smart Infrastructure 10/12/2022

Type summary

Type Stock

number Operating

voltage Running

speed Running time

5.5 mm Control signal Actuator

characteristic

SSB161.05U S55180-A151 AC/DC 24 V 5 s/mm 27.5 s ± 25 % DC 0...10 V Linear

Accessories

Product Type Stock Number Picture Name Conduit interface

ASY101 S55845-Z277 Conduit cover 3/8 inch flex conduit

Ordering When ordering, specify both type and quantity.

Example:

Type Stock number Designation Quantity

SSB161.05U S55180-A151 Electromotoric actuator 2

Delivery Valves and actuators can be ordered assembled in the factory or ordered separately. For

easier valve assembly, actuators ordered separately have the actuator stem fully retracted.

Equipment combinations

Valves

Combinable valves for SSB161.05U- 2-way Powermite 599 MZ Series

Action Nominal Line Size Flow Rate Connection

Inch mm Cv Kvs FxF FxUM AFxUM

Normally

Closed 0.5 15 0.4 (0.34) 599-01100 599-01101 -

0.5 15 0.63 (0.54) 599-01102 599-01103 -

0.5 15 1.0 (0.85) 599-01104 599-01105 -

0.5 15 1.6 (1.37) 599-01106 599-01107 -

0.5 15 2.5 (2.15) 599-01108 599-01109 -

0.5 15 4(3.44) 599-01110 599-01111 -

0.75 20 6.3 (5.43) 599-01112 599-01113 -

125 10 (8.6) 599-01114 – -

Normally

Open 0.5 15 0.4 (0.34) 599-01115 599-01116 -

0.5 15 0.63 (0.54) 599-01117 599-01118 –

0.5 15 1.0 (0.85) 599-01119 599-01120 –

0.5 15 2.5 (2.15) 599-01123 599-01124 599-01125

0.5 15 4(3.44) 599-01126 599-01127 599-01128

Siemens A6V12681516_enUS_a

Smart Infrastructure 10/12/2022

Action Nominal Line Size Flow Rate Connection

Inch mm Cv Kvs FxF FxUM AFxUM

0.75 20 6.3 (5.43) 599-01129 599-01130 –

125 10 (8.6) 599-01131 – –

Combinable valves for SSB161.05U – 3-way Powermite 599 MZ Series

Nominal Line Size Flow Rate Connection

Inch mm Cv Kvs FxF

0.5 15 0.4 (0.34) 599-01132

0.5 15 0.63 (0.54) 599-01133

0.5 15 1.0 (0.85) 599-01134

0.5 15 1.6 (1.37) 599-01135

0.5 15 2.5 (2.15) 599-01136

0.5 15 4(3.44) 599-01137

0.75 20 6.3 (5.43) 599-01138

1.00 25 10 (8.6) 599-01139

Product documentation

Topic Title Document ID

Installation Mounting instruction A6V13122037

Standards and directives CE declarations A5W00254962A

RCM conformity A5W00254983A

Environmental compatibility Environmental declarations A5W00242127A

Related documents such as the environmental declarations, CE declarations, etc., can be

downloaded from the following Internet address:

www.siemens.com/bt/download

Notes

Engineering The actuators must be electrically connected in accordance with local regulations (see

"Connection diagrams”).

CAUTION

National safety regulations

Failure to comply with national safety regulations may result in personal injury and property

damage.

●Observe national provisions and comply with the appropriate safety regulations.

Siemens A6V12681516_enUS_a

Smart Infrastructure 10/12/2022

Observe permissible temperatures (see "Technical data [▶9]").

Mounting

WARNING

●Do not use pipe wrenches, pliers or similar tools.

●Avoid lateral pressure or (cable) tension on the mounted actuator!

Valve and actuator are easy to assemble on site before commissioning:

●Remove protective cover from the valve body.

●Position the actuator and tighten the union nut manually.

●See "Mounting instructions" for graphical instructions.

Orientation

Commissioning When commissioning, check both wiring and functioning of the actuator.

●Actuator stem extends Normally open valve closes, normally closed valve opens

●Actuator stem retracts Normally open valve opens, normally closed valve closes

NOTICE

The actuator must be commissioned only with a correctly mounted valve in place!

Self-calibration When operating voltage is applied, the actuator self-calibrates (fully retracted ➙fully

extended ➙setpoint).

Power

Calibration

Fully retracted

Fullyextended

Siemens A6V12681516_enUS_a

Smart Infrastructure 10/12/2022

CAUTION

Never intervene manually during self-calibration.

NOTICE

●Correct calibration is only possible with valve stroke > 0.05 inch (1.2 mm). Valve stroke

< 0.05 inch (1.2 mm) > 1.2 mm. Valve stroke < 1.2 mm results in calibration failure.

●If calibration fails, the actuator performs another calibration automatically after

10 seconds.

●After three failed calibration attempts, the actuator stem remains in the extended

position and the valves are open.

Manual operation A 3-mm hexagonal wrench can be used to move the actuator to any position.

To move the actuator stem manually

1. Open the cover using a proper screwdriver.

2. Press and hold down button (a) illustrated below for at least three seconds.

– The actuator ignores any control signal from the controller.

3. Adjust the position of the actuator stem by rotating hexagonal wrench (b) illustrated

below clockwise or counter-clockwise.

– The actuator stem moves down if you rotate clockwise; it moves up if you rotate

counter-clockwise. The manually set position is retained.

4. To exit manual operation mode, press and hold down button (a) illustrated below again

for at least three seconds.

– The actuator runs a self-calibration automatically. Control signal sent from the

controller takes effect.

5. Close the cover.

NOTICE

If operating voltage is applied to actuator, press button (a) before and after manually

adjusting the position of the actuator stem. If no operating voltage and control signal are

applied, manual operation can be done without pressing button (a).

Cabling operation1. Unscrew cover screw

2. Remove cover

3 mm

(b)

(a)

>3s

Siemens A6V12681516_enUS_a

Smart Infrastructure 10/12/2022

3. Connect or disconnect wire terminals (terminal block is removable)

4. Install the cover

5. Screw in the cover screw

Maintenance The actuators require no maintenance.

WARNING

Operating voltage must be switched off during any maintenance!

NOTICE

When carrying out service work on the plant, note the following:

●Switch off operating voltage.

●If necessary, disconnect electrical connections from the terminals.

●The actuator must be commissioned only with a correctly mounted valve in place!

Repair

The actuators cannot be repaired; the complete unit must be replaced.

Disposal

The device is considered an electronic

device for disposal and may not be disposed

of as domestic waste.

●Dispose of the device through channels

provided for this purpose.

●Comply with all local and currently

applicable laws and regulations.

Warranty Technical data on specific applications are valid only together with Siemens products listed

under "Equipment combinations". Siemens rejects any and all warranties in the event that

third-party products are used.

Siemens A6V12681516_enUS_a

Smart Infrastructure 10/12/2022

Open Source Software (OSS)

Software license overview

These devices use Open Source Software (OSS). All Open Source Software components

used in the product (to include copyrights and licensing agreement) are available at

http://siemens.com/bt/download.

Firmware version OSS document Device

Document ID Title

2.10.0 or above A6V13503690 Readme OSS for Modulating Room Actuator 200N, 300N All

Siemens A6V12681516_enUS_a

Smart Infrastructure 10/12/2022

Technical data

Power supply

Operating voltage AC 24 V (± 15 %) or DC 24 V (± 20 %)

Frequency 50/60 Hz

Power consumption 3 VA (AC); 1.2 W (DC)

Primary fuse or breaker rating External, 2 A quick blow

Signal input

Control signal DC 0…10 V

Input impedance 100 kOhm

Parallel operation (number of actuators) Max. 101)

1) Provided that the controller output is sufficient.

Operating data

Position with de-energized contact Y See "Technical design [▶2]"

Running speed (time for 5.5 mm) < 5 s/mm ± 25 % (27.5 s ± 25 %)

Positioning force 45 lbf (200 N)

Stroke 0.05 to 0.25 inch (1.2…6.5 mm)

Permissible temperature of medium in the connected valve 34 to 248°F (1…120℃)

Electrical connection

Permissible length for signal lines 65 ft (20 m)

Wire cross section 18...20 AWG (0.5...0.75 mm²）

Cable diameter <0.2 inch (5 mm)

Mounting

Connection to valve Plastic coupling nut 3/4” inch

Orientation Above horizontal

Standards

EU conformity (CE) A5W00254962A

RCM conformity A5W00254983A

UKCA A5W00257055A

Housing protection degree NEMA 2 / IP20 (EN 60529)

Protection class according to EN 60730 III

Pollution degree 2

Siemens A6V12681516_enUS_a

Smart Infrastructure 10/12/2022

Standards

Overvoltage category III

Environmental compatibility The product environmental declaration

(A5W00242127A) contains data on environmentally

compatible product design and assessments (RoHS

compliance, materials composition, packaging,

environmental benefit, disposal).

UL Approval

Federal Communications Commission

UL as per UL60730-1, UL60730-2-14

http://ul.com/database

cUL as per CSA – CAN E60730-1, E730-2-14

FCC CFR 47 Part 15 Class B

ICES003 CAN ICES-3 (B)/NMB-3(B)

FCC regulations

Modification of this device to receive cellular radio telephone service signals is pro-

hibited under FCC rules and federal law.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Housing color

Cover/base 2003, Ti-Gray

Coupling nut RAL 9017

General ambient conditions

Operation Transport Storage

Temperature 34 to 122°F (1…50 ℃)-13 to 158°F (-25…70 ℃) -13 to 158°F (-25…70 ℃)

Humidity 5…95 % r.h.

non condensing <95 % r.h.

non condensing 5…95 % r.h.

non condensing

Atmospheric

pressure Min. 700 hPa, corresponding to

max. 3,000 m above sea level - -

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens SSA31.04 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RW40 Bedienungsanleitung

Siemens

Siemens HydroRanger 200 HMI Bedienungsanleitung

Siemens

Siemens 125-1957 Bedienungsanleitung

Siemens

Siemens ACVATIX SAX319.03 Bedienungsanleitung

Siemens

Siemens AEROGYR RWI65.01 Bedienungsanleitung

Siemens

Siemens instabus JB526C23 Bedienungsanleitung

Siemens

Siemens IQHeat Bedienungsanleitung

Siemens

Siemens SCALANCE M800 Bedienungsanleitung

Siemens

Siemens RWB27 Timeswitch Bedienungsanleitung

Siemens

Siemens OpenAir GBB13 1 Series Bedienungsanleitung

Siemens

Siemens OpenAir GDE141.1U Betriebsanleitung

Siemens

Siemens GED33 Series Bedienungsanleitung

Siemens

Siemens SSA955 Bedienungsanleitung

Siemens

Siemens SINUMERIK 828D Turning Bedienungsanleitung

Siemens

Siemens Synco700 RMK770 Bedienerhandbuch

Siemens

Siemens SINUMERIK 840Di Bedienungsanleitung

Siemens

Siemens OpenAir GND12x.1 Series Service-Handbuch

Siemens

Siemens TUTORbit POL687 Service-Handbuch

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens SIMATIC S7-1200 Bedienungsanleitung

Siemens

Siemens BR6000 Bedienungsanleitung

Siemens

Siemens BT300 LonWorks Gebrauchsanweisung

Siemens

Siemens OpenAir GCA Series Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung