Siemens SIMATIC 6ES7134-4FB01-0AB0 Bedienungsanleitung

SIMATIC ET 200S distributed I/O 2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

_____________

Preface

Properties

Parameters

Diagnostics

Analog value representation

Connecting

SIMATIC

ET 200S distributed I/O

2AI U ST analog electronic module

(6ES7134-4FB01-0AB0)

Manual

04/2007

A5E01076000-01

Safety Guidelines

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE

indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Commissioning and

operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes

in this documentation qualified persons are defined as persons who are authorized to commission, ground and

label devices, systems and circuits in accordance with established safety practices and standards.

Prescribed Usage

Note the following:

WARNING

This device may only be used for the applications described in the catalog or the technical description and only

in connection with devices or components from other manufacturers which have been approved or

recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,

positioning and assembly as well as careful operation and maintenance.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Siemens AG

Automation and Drives

Postfach 48 48

90327 NÜRNBERG

GERMANY

Ordernumber: A5E01076000-01

Ⓟ 09/2007

Technical data subject to change

2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

Manual, 04/2007, A5E01076000-01 3

Preface

Purpose of the manual

This manual supplements the

ET 200S Distributed I/O System

Operating Instructions.

General functions for the ET 200S are described in the

ET 200S Distributed I/O System

Operating Instructions.

The information in this document along with the operating instructions enables you to

commission the ET 200S.

Basic knowledge requirements

To understand these operating instructions you should have general knowledge of

automation engineering.

Scope of the manual

This manual applies to this ET 200S module. It describes the components that are valid at

the time of publication.

Recycling and disposal

Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable. For

environmentally compliant recycling and disposal of your electronic waste, please contact a

company certified for the disposal of electronic waste.

Additional support

If you have any questions relating to the products described in these operating instructions,

and do not find the answers in this document, please contact your local Siemens

representative.

http://www.siemens.com/automation/partner

The portal to our technical documentation for the various SIMATIC products and systems is

available at:

http://www.siemens.com/automation/simatic/portal

The online catalog and ordering system are available at:

http://www.siemens.com/automation/mall

Preface

2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

4 Manual, 04/2007, A5E01076000-01

Training center

We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation

system. Please contact your regional training center or the central training center in D -

90327, Nuremberg, Germany.

Phone: +49 (911) 895-3200.

http://www.siemens.com/sitrain

Technical Support

You can reach technical support for all A&D projects

● using the support request web form:

http://www.siemens.com/automation/support-request

● Phone: + 49 180 5050 222

● Fax: + 49 180 5050 223

For more information about our technical support, refer to our Web site at

http://www.siemens.de/automation/service

Service & Support on the Internet

In addition to our documentation services, you can also make use of our comprehensive

online knowledge base on the Internet.

http://www.siemens.com/automation/service&support

There you will find:

● Our Newsletter, which constantly provides you with the latest information about your

products.

● The right documentation for you using our Service & Support search engine.

● The bulletin board, a worldwide knowledge exchange for users and experts.

● Your local contact for Automation & Drives in our contact database.

● Information about on-site services, repairs, spare parts. Lots more can be found on our

"Services" pages.

2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

Manual, 04/2007, A5E01076000-01 5

Table of contents

Preface ...................................................................................................................................................... 3

1 Properties .................................................................................................................................................. 7

1.1 2AI U ST analog electronic module (6ES7134-4FB01-0AB0) .......................................................7

2 Parameters.............................................................................................................................................. 11

2.1 Parameters...................................................................................................................................11

2.2 Parameter description..................................................................................................................12

3 Diagnostics.............................................................................................................................................. 13

3.1 Diagnostics using LED display.....................................................................................................13

3.2 Error types....................................................................................................................................14

4 Analog value representation .................................................................................................................... 15

4.1 Introduction ..................................................................................................................................15

4.2 Analog value representation for measuring range with SIMATIC S7 ..........................................15

4.3 Measuring ranges ........................................................................................................................16

4.4 Effect on analog value representation .........................................................................................18

4.4.1 Effect of the supply voltage and the operating state on analog input values ..............................18

4.4.2 Effect of the value range on the 2AI U ST analog input ..............................................................18

5 Connecting .............................................................................................................................................. 19

5.1 Connecting measuring sensors ...................................................................................................19

5.2 Wiring unused channels of the analog input modules.................................................................22

5.3 Using the shield connection .........................................................................................................22

Index........................................................................................................................................................ 23

Table of contents

2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

6 Manual, 04/2007, A5E01076000-01

2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

Manual, 04/2007, A5E01076000-01 7

Properties 1

1.1 2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

Properties

● 2 inputs for measuring voltage

● Input ranges:

± 10 V, resolution 13 bits + sign

± 5 V, resolution 13 bits + sign

1 V to 5 V, resolution 13 bits

● Isolated from the load voltage L+

● Permissible common mode voltage 2 VACSS

● Extended temperature range from 0 to 50°C with vertical installation

General terminal assignment

Note

Terminals 4, 8, A4, A8, A3 and A7 are only available at specified terminal modules.

Terminal assignment for 2AI U ST (6ES7134-4FB01-0AB0)

Terminal Assignment Terminal Assignment Notes

1 M

0+ 5 M

2 M

0- 6 M

3 M

ana 7 M

ana

4 n.c. 8 n.c.

A4 AUX1 A8 AUX1

A3 AUX1 A7 AUX1

•Mn+: Input signal "+", channel n

•Mn-: Input signal "-", channel n

•Mana: Ground of the module

•n.c.: Not connected (max. 30 V DC can be connected)

•AUX1: Protective-conductor terminal or potential bus (freely usable

up to 230 VAC)

Properties

1.1 2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

8 Manual, 04/2007, A5E01076000-01

Usable terminal modules

Usable terminal modules for 2AI U ST (6ES7134-4FB01-0AB0)

TM-E15C26-A1

(6ES7193-4CA50-

0AA0)

TM-E15C24-A1

(6ES7193-4CA30-

0AA0)

TM-E15C24-01

(6ES7193-4CB30-

0AA0)

TM-E15C23-01

(6ES7193-4CB10-

0AA0)

Spring terminal

TM-E15S26-A1

(6ES7193-4CA40-

0AA0)

TM-E15S24-A1

(6ES7193-4CA20-

0AA0)

TM-E15S24-01

(6ES7193-4CB20-

0AA0)

TM-E15S23-01

(6ES7193-4CB00-

0AA0)

Screw-type terminal

TM-E15N26-A1

(6ES7193-4CA80-

0AA0)

TM-E15N24-A1

(6ES7193-4CA70-

0AA0)

TM-E15N24-01

(6ES7193-4CB70-

0AA0)

TM-E15N23-01

(6ES7193-4CB60-

0AA0)

Fast Connect

















$8; 







$8;

















$$





























0

0

0

3($8;

0

:LULQJH[DPSOHV

Block diagram













$'8

0$1$

9

/

0

08;

3

3

%DFNSODQHEXV

(76

EDFNSODQHEXV

LQWHUIDFH

FRQQHFWLRQ

Figure 1-1 Block diagram of the 2AI U ST

Properties

1.1 2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

Manual, 04/2007, A5E01076000-01 9

2AI U ST technical specifications (6ES7134-4FB01-0AB0)

Dimensions and weight

Width (mm) 15

Weight Approx. 40 g

Module-specific data

Supports isochronous operation No

Number of inputs 2

Cable length

•Shielded Max. 200 m

Parameter length 4 bytes

Address space 4 bytes

Voltages, currents, potentials

Rated load voltage L+ (from the power module) 24 VDC

•Reverse polarity protection Yes

Electrical isolation

•Between the channels and backplane bus Yes

•Between the channels and load voltage L+ Yes

•Between the channels No

Permissible potential difference

•Between the inputs and MANA (UCM) 2 VACSS

•Between MANA and the central grounding point

(UISO) 75 VDC / 60 VAC

Insulation tested 500 VDC

Current consumption

•From load voltage L+ Max. 30 mA

Power dissipation of the module Typically 0.6 W

Status, interrupts, diagnostics

Diagnostics function

•Group error Red "SF" LED

•Diagnostic functions readable Yes

Analog value generation

Measuring principle Integrative

Integration and cycle time/resolution per channel:

•Integration time can be assigned parameters Yes

•Interference frequency suppression in Hz 60 50

•Integration time in ms 16,7 20

•Conversion time in ms 55 65

•Cycle time in ms Number of active channels per module x

conversion time

•Resolution (including overshoot range) ± 10 V/13 bits + sign

± 5 V/13 bits + sign

1 V to 5 V/13 bits

Properties

1.1 2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

2AI U ST analog electronic module (6ES7134-4FB01-0AB0)

10 Manual, 04/2007, A5E01076000-01

Suppression of interference, limits of error

Interference voltage suppression for

f = n x (f1 ± 1 %), (f1 = interference frequency)

•Common-mode interference (USS)

•Series-mode interference

(peak interference value < rated value of input

range)

•Crosstalk between the inputs

Min. 90 dB

min. 70 dB

min. -50 dB

Operational limit

(in the entire temperature range, with reference to

the input range)

± 0,6 %

Basic error limit (operational limit at 25°C with

reference to input range)

± 0,4 %

Temperature error (with reference to the input

range)

±0.01 %/K

Linearity error (with reference to the input range) ± 0,01 %

Repeatability (in steady state at 25°C with

reference to input range)

± 0,05 %

Data for selecting a sensor

Input range (rated value)/input resistance

•Voltage ± 5 V/min. 100 kΩ

1 V to 5 V/min.100 kΩ

± 10 V/min. 100 kΩ

Permitted input voltage (destruction limit) 35 V continuous, 75 V at max. duration of 1 ms

(sampling ratio 1:20)

Smoothing of the measured values Yes, can be assigned parameters in 4 steps by

means of digital filtering

Step

None

Weak

Medium

Strong

Time constant

1 x cycle time

4 x cycle time

32 x cycle time

64 x cycle time

Inhaltsverzeichnis

Andere Siemens E/A-System Handbücher

Siemens

Siemens SIMATIC ET 200SP Benutzerhandbuch

Siemens

Siemens Simantic ET200SP Benutzerhandbuch

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens FDCIO222 Bedienungsanleitung

Siemens

Siemens FDCI221 Bedienungsanleitung

Siemens

Siemens N 262E11 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens FDCI361 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens Simatic ET200pro Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200AL Bedienungsanleitung

Siemens

Siemens Simatic 6DL2804-1 Series Montageanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens N 263E11 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S M151-3 PN Bedienungsanleitung

Siemens

Siemens DI 8x24VAC/48VUC BA Bedienungsanleitung

Siemens

Siemens Simatic 6DL2804-0 Series Bedienungsanleitung

Siemens

Siemens SIMATIC Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP DI 8x24VDC ST Bedienungsanleitung

Siemens

Siemens SIM-16 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP 6ES7134-6GD01-0BA1 Bedienungsanleitung

Siemens

Siemens MICROMASTER 440 GX Technische Daten

Siemens

Siemens Simatic ET 200S 2/4AI RTD ST Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung