Siemens SpeedStream 6515 Benutzerhandbuch

Safety and Certifications

007-0650-001 1

Important Information about the SpeedStream 6520, SpeedStream 6515:

Installation and Safe Usage Instructions:

1. Place the SpeedStream ADSL gateway in an upright horizontal orientation on a flat

surface.

2. Connect the manufacturer supplied AC to DC power adapter. The SpeedStream 6xxx

series gateways require the use of a 12 VDC, 1 A power adapter. Only use a manufacturer

supplied and approved power adapter.

3. Connect the Ethernet cable (provided) to the RJ45 port on the SpeedStream ADSL

Gateway labeled "Ethernet". Then connect the other end of the Ethernet Cable then to the

Ethernet port of a computer. Repeat as necessary for the available Ethernet ports.

4. If a USB port is available, connect the “B” end of the provided USB cable to the port on

the SpeedStream ADSL Gateway labeled "USB". Then connect the “A” end of the USB

Cable to the USB host port of a computer.

5. Connect the provided DSL Cable to the port on the SpeedStream ADSL Gateway labeled

"DSL". Connect the other end of the DSL Cable to a standard Phone Jack. Always use a

DSL cable with a minimum wire gauge of 26AWG.

6. If using a USB port, use the SpeedStream CD to configure the computer’s USB

connection.

When using this device, basic safety precautions should always be followed to reduce the

risk of fire, electric shock, and injury to persons including the following:

1. Do not use this product near water and avoid contact with moisture. For example, do not

use near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a

swimming pool. Care should be taken so that liquids are not spilled on this equipment.

2. Never insert objects into the vents of this equipment as this can result in the risk of

electrical shock or fire.

3. This equipment should only be operated from the type of power supply indicated on the

marking label.

4. Do not overload wall outlets or extension cords. Doing so can result in the risk of fire or

electrical shock.

5. Avoid blocking any vent openings or exhaust exits on this equipment. Do not place

equipment in a built-in installation such as a cabinet that may impede the flow of air through

the ventilation openings.

6. The equipment should be situated away from heat sources such as radiators, heat

registers, stoves, or other heat producing appliances and equipment.

7. Care should be taken to ensure that the power cord is routed, so it is not likely to be

walked on or pinched by items placed upon or next to it.

8. Unplug this equipment before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning only.

9. This equipment is not user serviceable and is to be serviced by qualified personnel only.

Do not disassemble this equipment. If service is required, disconnect all power and phones

lines from the equipment and consult qualified service personnel.

Save these Instructions!

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

Safety and Certifications

007-0650-001 2

Modifications:

You are cautioned that changes or modifications not expressly approved by the party

responsible for compliance could void your authority to operate the equipment.

FCC Responsible Party: Siemens Subscriber Networks, Inc.

4849 Alpha Road

Dallas, TX 75244

Phone: 972-852-1000

Radio Frequency Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

FCC Terminal Equipment Statements

This equipment complies with Part 68 of the FCC rules and the requirements adopted by

the ACTA. On the bottom side of this equipment is a label that contains, among other

information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this

number must be provided to the Telephone Company. A copy of the Suppliers Declaration

of Conformity to the FCC Part 68 and ACTA requirements can be found at:

http://www.part68.org.

This equipment has a Universal Service Order Code (USOC) of RJ11C, a Facility Interface

Code (FIC) of 02LS2, and a Service Order Code (SOC) of 7.0Y. The Telephone Company

may request this information when ordering service for this equipment.

A plug and jack used to connect this equipment to the premises wiring and telephone

network must comply with the applicable FCC Part 68 rules and requirements adopted by

the ACTA. A compliant telephone cord and modular plug is provided with this product. It is

designed to be connected to a compatible modular jack that is also compliant.

If this equipment causes harm to the telephone network, the telephone company will notify

you in advance that temporary discontinuance of service may be required. But if advance

notice isn't practical, the Telephone Company will notify the customer as soon as possible.

Also, you will be advised of your right to file a complaint with the FCC if you believe it is

necessary.

The Telephone Company may make changes to its facilities, equipment, operations or

procedures that could affect the operation of the equipment. If this happens the Telephone

Safety and Certifications

007-0650-001 3

Company will provide advance notice so you can make the necessary modifications to

maintain uninterrupted service.

This equipment is not user serviceable. If trouble is experienced with this equipment, for

repair or warranty information, please contact Siemens at:

Siemens Technical Support Services:

USA Telephone: +1 (972) 852-1000

Email: usa.800sieme[email protected]emens.com

RMA service hours:

8:00am - 5:00pm (CST) Monday - Friday

Siemens Subscriber Networks, Inc.

4849 Alpha Road

Dallas, TX 75244

Attn: RMA #

If the equipment is causing harm to the telephone network, the Telephone Company may

request that you disconnect the equipment until the problem is resolved.

This equipment is not intended for use on public coin phone service provided by the

Telephone Company. Connection to party line service is subject to state tariffs. (Contact

the state public utility commission, public service commission or corporation commission for

information.)

If your home has specially wired alarm equipment connected to the telephone line, ensure

the installation of this equipment does not disable your alarm equipment. If you have

questions about what will disable alarm equipment, consult your telephone company or a

qualified installer.

This equipment connects to the telephone network that can be vulnerable to electrical

surges as a result of lightning strikes and other events. Such events can be very

destructive to equipment connected to both the telephone network and to AC power

sources. It is strongly recommended that a surge arrestor be used to connect this

equipment to AC power in order to reduce the possibility of damage resulting from such

events.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

This device produces radio frequency energy in the 2.4 GHz spectrum. The antenna should

be positioned to keep a minimum distance of 20cm from the radiating element to any

nearby person.

Industry Canada Statements

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment

Technical Specifications. This is confirmed by the registration number displayed on the

equipment label. The abbreviation, IC, before the registration number signifies that

registration was performed based on a Declaration of Conformity indicating that Industry

Canada technical specifications were met. It does not imply that Industry Canada approved

the equipment.

Before installing this equipment, users should ensure that it is permissible to be connected

to the facilities of the local Telecommunications Company. The equipment must also be

Safety and Certifications

007-0650-001 4

installed using an acceptable method of connection. The customer should be aware that

compliance with the above conditions may not prevent degradation of service in some

situations. Repairs to certified equipment should be coordinated by a representative

designated by the supplier. Any repairs or alterations made by the user to this equipment,

or equipment malfunctions, may give the telecommunications company cause to request

the user to disconnect the equipment. Users should ensure for their own protection that the

electrical ground connections of the power utility, telephone lines, and internal metallic

water pipe system, if present, are connected together. This precaution may be particularly

important in rural areas. Caution: Users should not attempt to make such connections

themselves, but should contact the appropriate electric inspection authority, or electrician,

as appropriate.

The SpeedStream 6520, and SpeedStream 6515, comply with Canadian RSS-210.

NOTICE: To prevent radio interference to the licensed service, this device must be

operated indoors only and should be kept away from windows to provide maximum

shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to

licensing by Industry Canada. Modification of antenna gain or transmit power may require a

radio license from Industry Canada.

CE Mark Declaration of Conformance and Restrictions for European Union (EU)

Hereby, Siemens., declares SpeedStream 6520, and SpeedStream 6515 are in compliance

with the essential requirements and other relevant provisions of The Radio Equipment and

Telecommunications Terminal Equipment Directive 1999/5/EC. A copy of the Declaration

of Conformity can be found at:

http://www.icn.siemens.com/subscriber

English Hereby, Siemens Subscriber Networks, Inc., declares that this Broadband

ADSL Modem is in compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Finnish Siemens Subscriber Networks, Inc., vakuuttaa täten että Broadband ADSL

Modem tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja

sitä koskevien direktiivin muiden ehtojen mukainen.

Dutch Hierbij verklaart Siemens Subscriber Networks, Inc. dat het toestel

Broadband ADSL Modem in overeenstemming is met de essentiële eisen

en de andere relevante bepalingen van richtlijn 1999/5/EG

Bij deze verklaart Siemens Subscriber Networks, Inc.dat deze Broadband

ADSL Modem voldoet aan de essentiële eisen en aan de overige relevante

bepalingen van Richtlijn 1999/5/EC.

French Par la présente Siemens Subscriber Networks, Inc. déclare que l'appareil

Broadband ADSL Modem est conforme aux exigences essentielles et aux

autres dispositions pertinentes de la directive 1999/5/CE

Par la présente, Siemens Subscriber Networks, Inc., déclare que ce

Broadband ADSL Modem est conforme aux exigences essentielles et aux

autres dispositions de la directive 1999/5/CE qui lui sont applicables

Safety and Certifications

007-0650-001 5

Swedish Härmed intygar Siemens Subscriber Networks, Inc. att denna Broadband

ADSL Modem står I överensstämmelse med de väsentliga egenskapskrav

och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Danish Undertegnede Siemens Subscriber Networks, Inc. erklærer herved, at

følgende udstyr Broadband ADSL Modem overholder de væsentlige krav

og øvrige relevante krav i direktiv 1999/5/EF

German Hiermit erklärt Siemens Subscriber Networks, Inc., dass sich

dieser/diese/dieses Broadband ADSL Modem in Übereinstimmung mit den

grundlegenden Anforderungen und den anderen relevanten Vorschriften

der Richtlinie 1999/5/EG befindet". (BMWi)

Hiermit erklärt Siemens Subscriber Networks, Inc.die Übereinstimmung des

Gerätes Broadband ADSL Modem mit den grundlegenden Anforderungen

und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)

Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Siemens Subscriber Networks, Inc. ∆ΗΛΩΝΕΙ ΟΤΙ

Broadband ADSL Modem ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ

ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ

1999/5/ΕΚ

Italian Con la presente Siemens Subscriber Networks, Inc. dichiara che questo

Broadband ADSL Modem è conforme ai requisiti essenziali ed alle altre

disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Spanish Por medio de la presente Siemens Subscriber Networks, Inc. declara que

el Broadband ADSL Modem cumple con los requisitos esenciales y

cualesquiera otras disposiciones aplicables o exigibles de la Directiva

1999/5/CE

Portuguese Siemens Subscriber Networks, Inc. declara que este Broadband ADSL

Modem está conforme com os requisitos essenciais e outras disposições

da Directiva 1999/5/CE.

Malti Hawnhekk, Siemens Subscriber Networks, Inc., jiddikjara li dan Broadband

ADSL Modem jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti

oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC

Estonian Käesolevaga kinnitab Siemens Subscriber Networks, Inc. seadme

Broadband ADSL Modem vastavust direktiivi 1999/5/EÜ põhinõuetele ja

nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Hungarian Alulírott, Siemens Subscriber Networks, Inc. nyilatkozom, hogy a

Broadband ADSL Modem megfelel a vonatkozó alapvetõ

követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Slovak Siemens Subscriber Networks, Inc. týmto vyhlasuje, že Broadband ADSL

Modem spĺňa základné požiadavky a všetky príslušné ustanovenia

Smernice 1999/5/ES.

Czech Siemens Subscriber Networks, Inc. tímto prohlašuje, že tento Broadband

ADSL Modem je ve shoděse základními požadavky a dalšími příslušnými

ustanoveními směrnice 1999/5/ES.

Safety and Certifications

007-0650-001 6

Slovene Šiuo Siemens Subscriber Networks, Inc. deklaruoja, kad šis Broadband

ADSL Modem atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos

nuostatas.

Lithuanian Šiuo Siemens Subscriber Networks, Inc. deklaruoja, kad šis Broadband

ADSL Modem atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos

nuostatas.

Latvian Ar šo Siemens Subscriber Networks, Inc. deklarē, ka Broadband ADSL

Modem atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to

saistītajiem noteikumiem.

Restrictions in English

France: Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz.

Italy: If used outside of own premises, general authorisation is required.

Luxembourg: None General authorization required for public service.

Romania: On a secondary basis. Individual licence required. T/R 22-06 not implemented.

Restricciones en Español

Francia: Uso al aire libre limitado a 10 mW e.i.r.p. dentro de la venda 2454-2483.5

megaciclos.

Italia: Si está utilizada fuera de propias premisas, se requiere la autorización general.

Luxemburgo: ninguno autorización general requerida para el servicio público.

Rumania: Sobre una base secundaria. La licencia individual requirió. T/R 22-06 no

puesto en ejecucio'n.

Restrictions en Français

La France : Utilisation extérieure limitée à 10 mW e.i.r.p. dans la bande 2454-2483.5

mégahertz.

L'Italie : Si utilisé en dehors de de propres lieux, l'autorisation générale est exigée.

Le Luxembourg: aucun autorisation générale requise pour le service public La.

Roumanie : Sur une base secondaire. Le permis individuel a exigé. T/R 22-06 non mis en

application.

Limitazioni (Italiane)

La Francia: Uso esterno limitato a 10 Mw e.i.r.p. all'interno della fascia 2454-2483.5

megahertz.

L'Italia: Se usato fuori dei propri locali, l'autorizzazione generale è richiesta.

Il Lussemburgo: Nessuno autorizzazione generale richiesta per servizio pubblico.

La Romania: Su una base secondaria. Patente specifica richiesta. T/R 22-06 non

effettuato.

Beschränkungen (Deutsch)

Frankreich: Im Freiengebrauch begrenzt bis 10 mW e.i.r.p. innerhalb des Bandes 2454-

2483.5 MHz.

Italien: Wenn sie außerhalb eigener Voraussetzungen verwendet wird, wird allgemeine

Ermächtigung angefordert.

Luxemburg: Kein allgemeine Ermächtigung erfordert für allgemeinen Service.

Rumänien: Auf einer Sekundärgrundlage. Einzelne Lizenz erforderte. T/R 22-06 nicht

eingeführt.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Netzwerk-Router Handbücher

Siemens

Siemens SL2-141-I Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RSG2288 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RX1100 Bedienungsanleitung

Siemens

Siemens ADSL C-110 Bedienungsanleitung

Siemens

Siemens SCALANCE M800 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM i803 Bedienungsanleitung

Siemens

Siemens SCALANCE X308-2M Bedienungsanleitung

Siemens

Siemens SIMATIC NET SCALANCE W778-1 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RX1000P Bedienungsanleitung

Siemens

Siemens SLI-5310 Bedienungsanleitung

Siemens

Siemens SCALANCE S615 Bedienungsanleitung

Siemens

Siemens SIMATIC NET RUGGEDCOM RS920W Bedienungsanleitung

Siemens

Siemens Gigaset SX541 WLAN dsl Bedienungsanleitung

Siemens

Siemens SINAUT MD741-1 Benutzerhandbuch

Siemens

Siemens Santis ADSL 50 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RSG2100 Bedienungsanleitung

Siemens

Siemens SCALANCE X-200 Administratorhandbuch

Siemens

Siemens SpeedStream 2105 Bedienungsanleitung

Siemens

Siemens SCALANCE S615 Merkblatt

Siemens

Siemens Gigaset Optical LAN Adapter Duo Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RS910L Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RS900GP Bedienungsanleitung

Siemens

Siemens SIMATIC NET SCALANCE S615 Merkblatt

Siemens

Siemens SIMATIC NET RUGGEDCOM RX1400 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise