Siemens SLIM Bedienungsanleitung

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

P/N 315-034904C-3

OPERATION The Model SLIM Loop Isolator Module from Siemens Industry, Inc. isolates short

circuits on FS-250C analog loops. By placing devices between SLIMs during installa-

tion, a short in the wiring within that group is disconnected from the rest of the loop.

The remainder of the devices continue to operate.The SLIM operates in both Class A

and Class B circuits.

A yellow LED flashes when a device detects a short circuit. The SLIM then isolates

that part of the loop. When the short is removed, the SLIM automatically restores

the loop to normal operation.The SLIM does not have a loop address and therefore

does not require address programming nor does it reduce the loop capacity below

252 devices.

Remove all system power before installation, first the battery and then the AC.

ELECTRICAL RATINGS Voltage: 24 Vdc

Current: 1mA max

INSTALLATION The SLIM is a polarity insensitive module. Refer to Figure 1 for the location of the

two input terminals, two output terminals and earth ground. Line 1 and Line 2 can be

either line of the loop.

Terminal Number Description

1 In — Line 1

2 In — Line 2

3 Out — Line 1

4 Out — Line 2

5 Earth Ground

Mechanical Installation (See Figure 2)

• Use a standard 3 1/2-inch deep, double gang electrical

switchbox or a 4-inch square electrical box that is 2 1/8 inches

deep.

• Connect the field wiring. Press the SLIM into the box and

fasten the module plate to the box.

• Cover the module front plate with the plate supplied and

fasten with screws supplied.

Figure 1

SLIM-1 Module

Loop Isolator Module

Installation Instructions

Model SLIM

SWITCHPLATE

5-INCHES SQUARE

(SUPPLIED)

SWITCHPLATE

5-INCHES SQUARE

(SUPPLIED)

4-INCH SQUARE BOX

2 1/8-INCHES DEEP

DOUBLE GANG BOX

3 1/2-INCHES DEEP

Figure 2

Mounting the SLIM

Figure 3

SLIM Wiring Diagram - Class B Installation

The SLIM may be used in two circuit configurations as follows:

Class B (See Figure 3) In Class B wiring each SLIM isolates a branch on the circuit. Note that

a short on the main branch causes the entire loop to fail. To prevent this, mount the

SLIMs at the enclosure and run each branch independently.

Figure 4

SLIM Wiring Diagram - Class A Installation (Single Loop)

1. All wiring must comply with

national and local codes.

2. In order to provide adequate

protection, it is recom-

mended that you do not

install more than 20 devices

on a single SLIM.

3. Minimum wire gauge is

18 AWG.

4. The total wire resistance

(both wires) between SLIMs

cannot exceed 20 ohms.

5. Do not install more than 15

SLIMs per FDLC loop.

6. All circuits are supervised.

7. Refer to the FS-250C

Manual, P/N 315-049589C

for the list of compatible

devices.

8. All terminals are power

limited.

1. All wiring must comply with

national and local codes.

2. In order to provide adequate

protection, it is recom-

mended that you do not

install more than 20 devices

on a single SLIM.

3. Minimum wire gauge is

18 AWG.

4. The total wire resistance

(both wires) between SLIMs

cannot exceed 20 ohms.

5. Do not install more than 15

SLIMs per FDLC loop.

6. All circuits are supervised.

7. Refer to the FS-250C

Manual, P/N 315-049589C

for the list of compatible

devices, as applicable.

8. All terminals are power

limited.

ANALOG LOOP

LINE 1

LINE 2

IN IN OUT OUTIN IN OUT OUTIN IN OUT OUT EARTH EARTH EARTH

TO ANALOG

LOOP RETURN

INSIDE ENCLOSURE

TO ANALOG

LOOP FEED

LINE 1

LINE 2

LINE 1

IN IN OUT OUT

ININ

OUTOUT

EARTH

ININ

OUTOUT

EARTH ININ

OUTOUT

EARTH

IN IN OUT OUT EARTH IN IN OUT OUT EARTH

Siemens Canada Limited

Building Technologies Division

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

P/N 315-034904C-3

Class A Single Loop (See Figure 4) IIn Class A wiring the SLIMS are wired in series with the loop wiring.

This results in a single continuous loop. If any group in the loop has a short, that

group is lost and a Class A circuit failure results.

Andere Siemens Schutzvorrichtung Handbücher

Siemens

Siemens SIPROTEC 7UM62 Bedienungsanleitung

Siemens

Siemens TPS4 Series Fehlerbehebungshandbuch

Siemens

Siemens SIPROTEC 7UT613 series Bedienungsanleitung

Siemens

Siemens 7SJ82 Bedienungsanleitung

Siemens

Siemens SIMATIC NET LP798-2N Administratorhandbuch

Siemens

Siemens 5SV8101-6KK Bedienungsanleitung

Siemens

Siemens 7SA513 Series Bedienungsanleitung

Siemens

Siemens 6SL3760-8CV00-0FA0 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RU2 Bedienungsanleitung

Siemens

Siemens 7SG23 MSCDN - MP2A Bedienungsanleitung

Siemens

Siemens 5SD7 581-5 Bedienungsanleitung

Siemens

Siemens SENTRON Bedienungsanleitung

Siemens

Siemens siprotec 7SA522 Bedienungsanleitung

Siemens

Siemens Solkor 7PG2113 Bedienungsanleitung

Siemens

Siemens SIPROTEC 7SS52 Bedienungsanleitung

Siemens

Siemens Reyrolle 7SR46 Bedienungsanleitung

Siemens

Siemens Argus 7SR12 Bedienungsanleitung

Siemens

Siemens 7SR242 Duobias Bedienungsanleitung

Siemens

Siemens SIPROTEC 7SK80 Bedienungsanleitung

Siemens

Siemens SIPROTEC 7SJ531 Bedienungsanleitung

Siemens

Siemens Solkor 7PG2113 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens TPS4 13 Bedienungsanleitung

Siemens

Siemens SIPROTEC Bedienungsanleitung

Beliebte Schutzvorrichtung Handbücher anderer Marken

Sola HD

Sola HD STV100K Series Bedienungsanleitung

socomec

socomec COUNTIS AMd Bedienungsanleitung

Kemo Electronic

Kemo Electronic M148-24 Bedienungsanleitung

SK ClickClick Bedienungsanleitung

Endress+Hauser

Endress+Hauser HAW569 Bedienungsanleitung

Ultrasonic

Ultrasonic SonicPRO Bedienungsanleitung

nxt

nxt BIA-nXt-DPC 1-22 Bedienungsanleitung

TFortis

TFortis SG-Switch Bedienungsanleitung

BERNINI DESIGN

BERNINI DESIGN Be172 Bedienungsanleitung

Rayleigh Instruments

Rayleigh Instruments RI-ENERGYSET-3P-ESS-50-100 Bedienungsanleitung

GE Multilin 3 Series Bedienungsanleitung

E.K.T.

E.K.T. ke-DP01 Bedienungsanleitung

cias

cias MICRO-RAY Bedienungsanleitung

Sungrow

Sungrow PVS-16MH Bedienungsanleitung

Reer

Reer 32010 Bedienungsanleitung

Tyco

Tyco ESFR-17 Bedienungsanleitung

Ross

Ross Opengear SRA-8901-R Bedienungsanleitung

GE Multilin 850 Bedienungsanleitung