Siemens AP-220-MNT-W3 Bedienungsanleitung

AP-220-MNT-W3 Mount Kit

Installation Guide

0511857-01 | October 2015 1

Package Contents

Mounting bracket

RJ45 couplers (2)

RJ45 cables (2)

M3 x10mm pan head screws (6)

T6 Torx security screw

AP-220-MNT-W3 Drill Template

AP-220-MNT-W3 Mount Kit Installation Guide (this document)

Introduction

The AP-220-MNT-W3 Mount Kit offers a secure mounting solution for 220 Series access points. This mount

kit attaches to standard single and dual gang wall boxes, or mounts to a flat surface, such as a wall or

ceiling.

Installing the AP-220-MNT-W3 Mount Kit

Refer to the steps below for installing your AP-220-MNT-W3 Mount Kit.

Installing the AP-220-MNT-W3 to a Flat Surface

1. (Optional) Remove one or both punch-out panel(s) on the sides of the mounting bracket by pressing

firmly, as shown in Figure 1.

Figure 1 Removing the punch-out panels from the mounting bracket

To install the AP-220-MNT-W3 onto a flat surface, see Installing the AP-220-MNT-W3 to a Flat Surface. To install

the mounting bracket onto a wall box, see Installing the Mount Housing onto a Wall Box.

2 AP-220-MNT-W3 | Installation Guide

2. Tape the AP-220-MNT-W3 Drill Template to the desired location and drill holes where indicated by the

template.

3. Once the holes have been drilled, remove the drill template and position the mounting bracket flat

against the surface. Align the holes of the mounting bracket with the pre drilled holes, then screw the

housing into place.

4. Press the RJ45 coupler(s) into the housing(s) located in the upper corner(s) of the mounting bracket

until locked into place in the housing(s), as shown in Figure 2.

Figure 2 Attaching the RJ45 couplers to the mount

5. Remove the RJ45 cable(s) from the bag and insert the end(s) into the inner-facing port(s) of the

couplers. See Figure 3.

Figure 3 Inserting the RJ45 cables into the coupler

6. Connect the opposite end(s) of the RJ45 cable(s) to the ENET0 and/or ENET1 port(s), located on the

back of the access point.

Screws for step3 are not included in this kit and may vary depending on the surface type.

AP-220-MNT-W3 | Installation Guide 3

7. Once the RJ45 cable(s) are attached, align the pins on the rear panel of the access point with the slots on

the mounting bracket. Press the button on the bottom of the mounting bracket and slide the access point

into the bracket. Release the button to secure the access point to the mounting bracket, as shown in

Figure 4.

Figure 4 Securing the access point to the mounting bracket

8. To lock the access point to the mounting bracket, insert the T6 Torx security screw into the hole beside

the button, located at the bottom of the mount, then tighten the screw until it is snug.

9. After the access point is securely fastened to the mounting bracket, connect the Ethernet cable(s) to the

appropriate RJ45 coupler port(s) on either side of the mount.

Installing the Mount Housing onto a Wall Box

1. Align the holes on the mounting bracket with the corresponding holes on the wall box. To install this kit

to a single gang wall box, refer to Figure 5. To install this mount kit to a dual gang wall box, refer to

Figure 6. Then, using the 10mm machine screws, fasten the mount housing to the wall box using the

holes indicated.

Figure 5 Installing the mounting bracket to a single-gang wall box

4 AP-220-MNT-W3 | Installation Guide

Figure 6 Installing the mounting bracket to a dual-gang wall box

2. Route Ethernet cable(s) through the back of the mount housing, as shown in Figure 5 and Figure 6.

Connect the cable(s) to the ENET0 and/or ENET1 port on the back of the access point.

3. Once the cable(s) is/are connected to the access point, align the pins on the rear panel of the access

point with the slots on the mount housing. Press the button on the bottom of the mount housing and

slide the access point into the slots. Release the button to secure the access point to the mounting

bracket. See Figure 7.

Figure 7 Securing the access point to the mounting bracket

4. To lock the access point to the mounting bracket, insert the T6 Torx security screw into the hole beside

the button, located at the bottom of the mount, then tighten until the screw is snug.

CONSOLE ENET1 ENET0

56V…

—350mA

12V…— 25A

AP-220-MNT-W3 Mount Kit

Mounting Template

0511858-01 | October 2015 1

Use the image below as template to mount the AP-220-MNT-W3 Mount Kit.

23.0 mm

139.90 mm

83.0 mm

All mounting holes have a 4 mm diameter.

Inhaltsverzeichnis

Andere Siemens Rack & Stand Handbücher

Siemens

Siemens ASK77.5 Bedienungsanleitung

Siemens

Siemens HZ1070 Leitfaden

Siemens

Siemens Actavix ASK33 Bedienungsanleitung

Siemens

Siemens H1900 Bedienungsanleitung

Siemens

Siemens 8PQ9800-8AA87 Bedienungsanleitung

Siemens

Siemens 8PQ9800-7AA38 Bedienungsanleitung

Siemens

Siemens CHBA221 Series Bedienungsanleitung

Siemens

Siemens 8PQ9801-5AA26 Bedienungsanleitung

Siemens

Siemens SENTRON 3VL160 Bedienungsanleitung

Siemens

Siemens 3WL Series Bedienungsanleitung

Siemens

Siemens KNX GAMMA AP 258E11 Bedienungsanleitung

Siemens

Siemens 8PQ9801-7AA21 Bedienungsanleitung

Siemens

Siemens H1800 Bedienungsanleitung

Siemens

Siemens 8PQ9800-3AA80 Bedienungsanleitung

Siemens

Siemens SIPART PS2 Handbuch

Siemens

Siemens 3VL/3VA Bedienungsanleitung

Siemens

Siemens SIRIUS 3TX7680-1B Bedienungsanleitung

Siemens

Siemens 8PQ9800-4AA11 Bedienungsanleitung

Siemens

Siemens 8PQ9802-7AA22 Bedienungsanleitung

Siemens

Siemens 3VL800-1250 Bedienungsanleitung

Siemens

Siemens SIMATIC IPC647D Bedienungsanleitung

Siemens

Siemens 3KC9811-0 Bedienungsanleitung

Siemens

Siemens 8PQ9800-0AA18 Bedienungsanleitung

Siemens

Siemens FHA2017-A1 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung