Siemens SITRANS F FUH1010 Series Bedienungsanleitung

6/2014Edition

Answers for industry.

Operating Instructions

SITRANS FUH1010 NEMA 7 Compact

Interface Detector 7ME3601-1, 7ME3601-2

SITRANS F

Siemens Hardware

E-1

1010FMA-45

Errata

Power Supply Wiring Procedure Update

ERRATA

NOTE: The following applies to System 1010X, 1010BX, 1010DVX, 1010PVX, 1010GX,

1010GCX, 1010GCSX and 1010SPVX Flowmeter installation manuals.

Replace the “Power Connections” description and set up procedure with the following. Note that

paragraph numbers are different for all the above mentioned manuals. The example below is for

the 1010X manual.

NOTE: For flowmeters refer to drawings 1010X-7 (1 of 3) & 1010DX-7 (1 of 3) and

for Interface Detectors refer to drawings 1010BX-7 (1 of 3) & 1010BDX-7

(1 of 3).

2.2 POWER CONNECTIONS

2.2.1 INPUT POWER CONNECTOR (P8) AND FUSE (F1) LOCATIONS

The standard 1010X flow computer either requires 100/120/200 VAC or one of three 9-36 VDC

power sources for its power input. The power input is protected by a GMA 2A fuse (F1). Please

replace this fuse with the exact type if it becomes necessary to do so.

This must be

connected to

Earth Ground.

Fuse (F1) GMA 2A

Cable

Clamp

AC HOT NEU GND

DC + - GND

WARNING

Do not connect AC or

DC power to flowmeter

until the correct type of

input power is de-

termined. See P/N

tables on next page.

Contact with exposed

wiring may lead to fire,

electric shock, or seri-

ous personal injury.

WARNING

Connect power per instructions below.

See field manual for complete power

supply wiring procedures.

Terminal

Number

1010X-6SS2

90-230 VAC

(Single Phase)

Hot

Neutral

Ground

Sample Power Label Located Inside Rear

Housing Cover.

Siemens Hardware

E-2

1010FMA-45Errata

2.2.2 POWER SUPPLY WIRING

lUsing a 1/16" Hex key, loosen the 1010X Rear Housing Cover locking setscrew.

lUnscrew the Rear Housing Cover and remove.

IMPORTANT: Power Supply label is located inside the Rear Housing cover.

lLocate power supply connector J8. Use the tables below and the part number of your unit to

determine the correct input power source. (See also metal ID label on unit housing.)

lPull wires through flowmeter case conduit cable hole.

lWire input power connector P8 for AC or DC power as shown below. Insert wires into wire

entry holes and secure by tightening wire clamp screws (see note on next page).

Terminal 1010X-6SS2 1010X-6ZNS2 1010X-6ZPS2 1010X-6Z

Number

1Hot Positive Positive (Gnd) Positive

2Neutral Negative (Gnd) Negative Negative

3Ground Ground Ground Ground

Input Power Connector (P8) Wiring

NOTE: Loosen Wire

Clamp Screw, insert

stripped end of wire

and then retighten.

GND

HOT

NEU

Connector

Mounting

Screws

Stripped Wire Wire

Clamp

Screws

NOTE: Power Supply connector wires should be stripped stranded or solid conductors

AWG 12 -18.

Root Meter Number

Transducer Support

Relay Support

Numeric Display

Power Supply Option

1010X-T2KNZPL2-S2----Safety Rating Option

Language Option

*Typical 1010X Part Number Construction:

Meter Part Number * Power Supply P/N User Supplied Power

Contains S prior to S_Code 1010X-6SS2 90-230 VAC Single Phase

Contains a ZN prior to S_Code 1010X-6ZNS2 9-36 VDC Negative Ground

Contains a ZP prior to S_Code 1010X-6ZPS2 9-36 VDC Positive Ground

Contains a Z at end of P/N 1010X-6Z 9-36 VDC Floating

E-3

1010FMA-45

Errata

2.3 THE MENU LOCKOUT SWITCH

System 1010X includes a menu lockout switch to prevent unauthorized access to the Installation

Menu. In addition, a password entry option is available (see Channel Setup). The menu lockout

switch (S1) resides on the I/O module on the right side of I/O wiring terminal block TB1 (see

below). Please switch to the unlocked position before attempting to program the flowmeter. We

recommend that the installation menu remains locked during normal operation. (Refer to appro-

priate manual section for TB1 and TB2 signal wiring.)

Menu Lockout

Switch (S1)

NOTE: The input power connector consists of a removable wire plug and PCB header located on

the 1010X-8 I/O module. Two screws secure the wire plug to the header. The connector assembly

is fully polarized for fast and easy mating. The wire plug accepts stranded or solid conductors of

AWG 12 - 18. To insert a wire into the wire plug, strip back the insulation by 0.31" (8 mm), loosen

the wire clamp screw, insert the stripped wire end and then re-tighten the wire clamp screw.

lPlug input power connector P8 into connector J8 and secure using two captive connector

mounting screws as indicated above.

lSecure power-input cable with cable clamp to prevent wire breakage.

lReplace Rear Housing Cover and tighten setscrew.

lConnect the power cables to the appropriate power source previously selected from the tables

above and power up unit.

lIf unit is operational, turn power off and install transducer cables.

Siemens Hardware

E-1

1010FMA-61

Errata

1. FUH1010 Interface Detector NEMA 7 Compact Flow Meter Manual

Troubleshooting Table Update

In the FUH1010 Interface Detector NEMA 7 Compact flow meter manual P/N CQO:1010BXFM-3 Revison

B replace the troubleshooting table in Section 2 - Installation Menu on pages 2-58, 2-59 and 2-60 with

the following:

Error or Message Probable Cause Solution

(continued)

Delete an obsolete site or clear

Datalogger memory to make

room for the new data.

Memory Full!

Memory Corrupted!

Response to an attempt to save site

data when data memory is full.

Memory read error occurred while

accessing the active site data.

Chan Not Setup Response to an attempt to invoke

an operation that requires a chan-

nel to be enabled.

Refer to F4 reset procedure in

the Operation Instructions

manual.

Enable the channel [Channel

Setup Channel - Enable - Yes].

Note that a channel cannot be

enabled until an “Install” opera-

tion is completed.

Clr Active Memory? Use this function to restore opera-

tion if a severe event (e.g. a violent

power surge) disrupts system

operation.

Refer to F4 reset procedure in

the Operation Instructions

manual.

Clr Save Data? [Clr Saved Data?] only appears

after pressing <Down Arrow> in

response to [Clr Active Memory?].

Answering [Yes] to [Clr Saved

Data?] will erase ALL saved

data. To invoke in RS-232 serial

mode, type @@@ and then

press <ENTER> key.

<EOT> Response to a request to output

Datalogger data to the printer or

the Graphics screen when no

datalogger data exists or at the end

of a transmitted file.

Set up the Datalogger.

No Sites - Press <ENTER>

Response upon charging previously

entered data when security switch

is in [Disable] position or security

code has been entered.

Create a site.

Security

Response while trying to recall/

delete a site setup when no sites

are stored.

Change switch position to

[Enable].

Enter previously set security

code.

Meter requires service. Request

RMA.

RTC Error Component level problem.

ERRATA

FUH1010 Interface Detector Compact NEMA 7 Manual Updates

Siemens Hardware

E-2

1010FMA-61Errata

Error or Message Probable Cause Solution

• Recouple sensors with fresh

couplant.

• Install Sensors in Direct mount

mode.

• Note: If problem persists call

Tech support.

- - -F - - -Fault Alarm • Loss of signal signal strength

• Change of Rx signal location (Beam

Blowing)

Re-space Index The measured liquid sonic velocity

(Vs) is more than +/- 25 % of the av-

erage Vs range.

• Ensure proper pipe dimensions

and/or Liquid data entries are cor-

rect.

• Properly enter correct Sensor

Size into meter [Install Sensor]

menu.

• Confirm sensor spacing is cor-

rect by checking [Install Sensor]

menu spacing parameters.

This may be due to one of the fol-

lowing:

• An out-of-range data entry.

• An invalid condition; (e.g.,

overlapping sensors in Reflect

Mode). If selecting Direct Mode

does not resolve, review all site

setup and sensor installation

choices; particularly data en-

tered for the pipe and liquid.

• In Reflect Mode, the flow

meter detects that the pipe wall

signal may impinge upon the

liquid signal. Use Direct Mode

instead.

Trigger <ENTER>, <UP Arrow>,

<DOWN Arrow>, or <LEFT Ar-

row> to abort install routine. Con-

tinue programming other site data

in anticipation of resolving the dif-

ficulty later. Call technical support

for help if necessary.

During the Initial Makeup, the system

detects invalid sensor spacing, erro-

neous liquid/pipe parameters, or

some other factor that prevents it

from completing the Initial Makeup.

Invalid Setup (use Direct Mode)

(continued)

E-3

1010FMA-61

Errata

Error or Message Probable Cause Solution

Some reasons for low signal are:

• Invoking [Install Complete?] on

an empty pipe.

• Coupling compound insufficient,

not applied or evaporated. Reap-

ply couplant.

• A disconnected or broken sen-

sor cable.

• The pipe needs to be condi-

tioned at the mounting location.

• Flush out large air bubbles.

• The sensor cables are defec-

tive or not connected to the cor-

rect channel.

• The Set Empty routine per-

formed when pipe was NOT ac-

tually empty.

• If you locate and correct the im-

proper condition immediately trig-

ger <ENTER> to resume the in-

stallation procedure. Otherwise,

trigger the <Left Arrow> to abort

the installation and conduct a thor-

ough investigation.

Low Signal - Press <ENTER> During the Initial Makeup the flow

meter decides that a level of the re-

ceive signal is insufficient for proper

operation.

Attempt to improve operating con-

ditions by reinstalling the sensors

at a different spacing offset, or

even at a different location on the

pipe.

Switching from Reflect to Direct

Mount may solve the problem.

However, operation may not be

possible if there is poor liquid, pipe

wall sonic conductivity or extreme

liquid aeration.

If it appears that the flow meter can

not complete an Initial Makeup this

means that the pipe and/or liquid con-

ditions do not permit a recieve signal

that meets the flow detection stan-

dards.

The system will not operate.

Detection Fault

Siemens Hardware

E-4

1010FMA-61Errata

2. DIN Pipe Table Note

In Section 2, add the following note right after paragraph 2.2.1 How to Select a Pipe Class:

NOTE:

The DN sizes listed in the [Select Pipe Size] menu option list are referenced to DIN Table

2448. After selecting pipe size, check pipe OD and wall thickness for correct dimensions.

3. Empty Pipe Set Procedure Update

In Section 2, paragraph 2.4.10 Empty Pipe Set Menu replace the introductory paragraphs and

warning with the following:

The flow meter performs the MTYmatic routine automatically during its Initial Make-up to estab-

lish a standard setting for the Empty Pipe alarm. This process is normally sufficient for setting

this parameter. The [Empty Pipe Set] option list allows you to re-invoke MTYmatic, use an

Actual MTY routine (if application conditions allow you to empty and refill the pipe) or use the

Set Empty routine to set the empty pipe threshold by direct numeric entry.

How To Use the Actual MTY Command

If application conditions allow you to empty and refill the pipe, then you may choose to perform

the Actual Empty procedure; however, it is not required to do so.

WARNING: NEVER perform the Actual MTY procedure if the pipe can not be emptied.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Sicherheitssensor Handbücher

Siemens

Siemens SICAM V01.00 Bedienungsanleitung

Siemens

Siemens ELP 319 Service-Handbuch

Siemens

Siemens FDOOTC441 Bedienungsanleitung

Siemens

Siemens HI921 Bedienungsanleitung

Siemens

Siemens FDF241-9 Bedienungsanleitung

Siemens

Siemens OOH740-A9-Ex Bedienungsanleitung

Siemens

Siemens DELTA i-system 1,1 Komfort 5TC1 505 Bedienungsanleitung

Siemens

Siemens milltronics Bedienungsanleitung

Siemens

Siemens 5TC1700 Bedienungsanleitung

Siemens

Siemens FDF241-9 Bedienungsanleitung

Siemens

Siemens GM730 Bedienungsanleitung

Siemens

Siemens DB110 Bedienungsanleitung

Siemens

Siemens FDL241-9 Leitfaden

Siemens

Siemens FDOOT271 Leitfaden

Siemens

Siemens DELTA iris 5TG5930-2 Series Bedienungsanleitung

Siemens

Siemens FS20 Technisches Handbuch

Siemens

Siemens SA-3I Bedienungsanleitung

Siemens

Siemens GAMMA instabus AP 251/11 Service-Handbuch

Siemens

Siemens Cerberus CS1140 Leitfaden

Siemens

Siemens QRI Series Bedienungsanleitung

Siemens

Siemens 667/HB/47200/000 Bedienungsanleitung

Siemens

Siemens S7-1500F Bedienungsanleitung

Siemens

Siemens Sinteso FD20 Bedienungsanleitung

Siemens

Siemens AGB600 Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung

Solinst

Solinst 301 Bedienungsanleitung

Pyronix

Pyronix KX10DTP Bedienungsanleitung