Siemens WAC 12 Bedienungsanleitung

8AA9992 - D1 - 10/11/2000 - UK -

Fig. 1

Fig. 2b

Fig. 3

Fig. 2a

3.2 Product overview (Fig. 2)

- Knockouts Q, Tfor cable inlet.

- Knockouts W, Efor attachment of housing.

- Knockout Rback tamper contact.

- Speaker Y.

- WMC 12 circuit board U.

3.3 WMC 12 circuit board (Fig. 3)

- E-Bus connection }.

- Audio connection {to central control unit.

- Audio connection Ito WAC 11 or WAS 11.

- Tamper input Ofor WAC 11 or WAS 11.

- LED Q, flashes when E-Bus is o.k.

- LED R, flashes to outside during monitoring (microphone

active).

- Address button W.

- Switch Efor "microphone active" LED.

- Tamper switch P.

- Microphone Y.

- Potentiometer Tfor speaker volume.

- Potentiometer Ufor microphone sensitivity.

1. Product description

The WAC 12 is used to verify audio alarms. It is fitted with a

speaker and microphone. It can be controlled through the E-

Bus, with the audio signal connected to the central control unit

via an audio module (e.g. WMA 11). The WAC 12 also serves as

a master for the unaddressable WAC 11 and WAS 11.

2. Supply package

The WAC 12 UK package contains the following

- One WAC 12

- One WLC 12 UK language kit complete with:

- Installation instructions.

3. Mounting instructions

The WAC 12 is designed for mounting in dry indoor rooms.

To ensure good acoustics, note the following points.

- Mount 2 to 2.5 m above floor level.

- Maintain adequate distance from noise sources (ventilation

openings, fans etc.).

- Direct towards the centre of the space to be monitored.

- Do not mount on vibrating surfaces.

- The maximum length of the audio connection between the

WAC 12 and central control unit is 200 m.

3.1 Opening the housing (Fig.1)

1 - Using screwdriver Q, press locking tab to release.

2 - Lift off cover W.

Installation Instructions

WAC 12

WLC 12 UK

20 800 042.0-010

Fig. 4

Fig. 5a

E-Bus from the cen-

tral control unit

E-Bus to other

accessories

Fig. 5b

WAC 12 WAC/WAS 11

Audio to

other

WAC 12

Fig. 5c

e.g. WMA 11 WAC 12

WAS 11

Fig. 5d

WAC 12 WAC 11 WAC 11

The right to make technical changes to the described equipment without prior notice is

reserved.

3.4 Mounting (Fig. 4)

- The housing can be mounted flat or at 45o.

- Always use two attaching points which are one above the

other, including for corner mounting.

4. Wiring

4.1 E-Bus (Fig. 5a)

The use of type 24 AWG 7x0,2 mm dia. cable is recommended.

The E-Bus cable shall not be more than 500 m long. The WAC 12

must be connected to the central control unit via the E-Bus (B1-,

B2, B3, B4+). It can be routed parallel to other accessories.

4.2 Tamper (Fig. 5a)

The tamper inputs T- and T+ must be short-circuited if not wired

to a WAC 11 or WAS 11.

4.3 Audio (Fig. 5b)

To avoid side-tone, a twisted core pair at least 0.6 mm in dia.

must be used. The audio connection to the central control unit

must not be more than 200 m long. The audio output depends

on the cable length and core cross-section. The audio connection

(A- and A+) of the WAC 12 must be connected to the audio input

(A- and A+) of the central control unit (e.g. WMA 11).

4.3.1. WAC 11 and WAS 11 (Fig. 5c)

The audio outputs (A- and A+) of the WAC 11 and WAS 11 are

connected to the audio inputs (AE- and AE+) of the WAC 12. The

tamper outputs (T,T) of the WAC 11 and WAS 11 are connected

in series to the tamper inputs (T- and T+) of the WAC 12.

Where several WAC 11 are used, all WAC 11 must be connected

directly to the WAC 12 to obtain optimum performance (Fig. 5d).

5. Start-up

5.1 Microphone sensitivity

The sensitivity of the microphone must be matched to the room

and ambient noises (potentiometer U, Fig. 3).

Where sensitivity is reduced, the reception of quiet signals

naturally reduces. The following ranges are normally obtained.

- Approx. 3.5 m with potentiometer on min.

- Approx. 6.5 m with potentiometer on mid position.

- Approx. 8.5 m with potentiometer on max.

5.2 Speaker

Set the required volume using potentiometer (Y, Fig. 3).

5.3 LED „microphone active“

- Switch (E, Fig. 3) open: LED active.

- Switch (E, Fig. 3) closed: LED inactive.

6. Close housing

1 - Engage cover at the top in the openings in the base of the

housing.

2 - Close the cover by pushing downwards until the locking

tab engages.

7.Technical data

Supply Through E-Bus

Power consumption, quiescent state 5 mA

Power consumption, "challenge" state 24 mA

Operating temperature -10°C to +55°C

Housing material ABS

Dimension in mm H 145 x B 105 x T 70

Safety class IP 30

Weight 230g

T+

T- B2 B3 B4+

B1-

A+

A-

A+

A-

T+

T-

AE+

AE- TTA-A+

NC TTA-A+

A+ A+

A- A-

AE+

AE-

Inhaltsverzeichnis

Andere Siemens Sicherheitssystem Handbücher

Siemens

Siemens SIRIUS 8WD4420-0EA Bedienungsanleitung

Siemens

Siemens IC60 Bedienungsanleitung

Siemens

Siemens milltronics MFA 4P Bedienungsanleitung

Siemens

Siemens NCC-G16 Bedienungsanleitung

Siemens

Siemens FDM225 Bedienungsanleitung

Siemens

Siemens FDM225 Bedienungsanleitung

Siemens

Siemens FDM1101-R Series Bedienungsanleitung

Siemens

Siemens IMKW6-10 Bedienungsanleitung

Siemens

Siemens FDM221 Bedienungsanleitung

Siemens

Siemens SINAMICS S120 Bedienungsanleitung

Siemens

Siemens Cerberus PACE Bedienungsanleitung

Siemens

Siemens SIRIUS 8WD42 Bedienungsanleitung

Siemens

Siemens RB-6 L-801A Bedienungsanleitung

Siemens

Siemens FDAI91 Bedienungsanleitung

Siemens

Siemens IC60 Bedienungsanleitung

Siemens

Siemens ISRW6-12 Bedienungsanleitung

Siemens

Siemens Codelock K44 Duo Bedienungsanleitung

Siemens

Siemens CP-48 Bedienungsanleitung

Siemens

Siemens FT2009-U1 Bedienungsanleitung

Siemens

Siemens SISTORE AX4 Bedienungsanleitung

Siemens

Siemens IC60 Bedienungsanleitung

Siemens

Siemens Cerberus PACE Leitfaden

Siemens

Siemens FDM275 Bedienungsanleitung

Siemens

Siemens FDM221 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung