Siemens APOGEE Ethernet Microserver 2100 Bedienungsanleitung

Installation Instructions

Document No. 538-924

October 10, 2019

APOGEE Ethernet Microserver 2100 (AEM2100)

Unrestricted Item Number: 538-924, Rev. AB Page 1 of 2

Product Description

The APOGEE® Ethernet Microserver 2100 (AEM2100)

allows APOGEE field panel networks to communicate

with Insight® workstations across an Ethernet. A

second serial port independently connects to the MMI.

The AEM2100 supports Autosensing, 10Base-T,

100Base-TX, half and full duplex TCP/IP.

Product Numbers

538-997 AEM2100 115V (Includes two serial cables

with RJ11 connectors and 100-240V 50/60

Hz power supply with US 2-Prong plug)

CAUTION:

Only use the AEM2100 power pack

with the AEM2100. Do not use the

power pack with other devices.

Expected Installation Time

15 minutes

Caution Notation

CAUTION

Equipment damage or loss

of data may occur if you do

not follow a procedure as

specified.

Required Tools

•1/8-inch flat-blade screwdriver

•Cable ties

•Laptop computer

Required Materials

•538-900 AEM Accessory Kit for configuration

•US 2-Prong line cord adapter for the country

where installed if not US 115V.

•AEM2100 Privileged Password, IP Address,

Subnet Mask, Gateway IP Address or DHCP

Name, and Domain Name

Prerequisites

•Ethernet wiring is pulled into the field panel

and terminated with one of the following:

−Certified Category 5 or higher wiring,

outlets, and patch cables for 100Base-TX

operation.

−Category 3 minimum and RJ45 plug.

−PNET1GB (Manufacturer APC) Surge

Suppressor for S1 Smoke Control or

industrial installations

•The TCP\IP server on Ethernet wiring.

•Field panel containing the AEM2100 is running

APOGEE Firmware Revision 2.2 or later.

•Computer defining the AEM2100 is running

APOGEE Insight Revision 3.1.2 or later or

DESIGO CC.

NOTE: If an AEM BLN contains pre-APOGEE field

panels, pre-APOGEE naming conventions

must be used in the APOGEE field panel and

Insight workstation.

Pre-Installation Configuration

CAUTION:

Do not plug the Ethernet cable into the

AEM2100 until the AEM2100 is configured

with IP Addresses or DHCP Names.

•Pre-Configure AEM2100 using Channel 1 and

a 9-pin cable to PC or Laptop COM port at

9600 bps, 8 data bit, 1 stop bit, no parity.

Press “xxx” immediately after powering up

AEM2100. Record and set server per Network

Administrator instructions.

Record the fixed IP Address or DHCP Name and

the System Name and Addresses in Table 1.

Document No. 538-924

Installation Instructions

October 10, 2019

Unrestricted Information in this publication is based on current specifications. The company reserves the right to make changes in

specifications and models as design improvements are introduced. Other product or company names mentioned herein may be the

Siemens Industry, Inc.

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

U.S.A.

Your feedback is important to us. If you have

comments about this document, please send

them to [email protected]om

Document No. 538-924

Printed in the U.S.A.

Page 2 of 2

Table 1. AEM2100 Connection Information.

IP Addresses

AEM IP Address

. . .

Subnet Mask

. . .

Gateway IP Address

. . .

DHCP Names

AEM2100 Name

Domain Name

System Name and Addresses

BLN System Name

Field Panel Address

Insight Address

Installation

1. Place the AEM2100 on the bottom of the field

panel enclosure.

2. Plug the Ethernet patch cable into the RJ45

Ethernet port on the AEM2100.

3. Connect the other end of the Ethernet patch

cable as follows:

•For normal installations, plug into the jack

box inside the field panel. Skip to Step 6.

•For S1 Smoke Control plug into the surge

suppressor (Figure 1).

4. Plug the surge suppressor green patch cable

into the jack box inside the field panel.

5. Connect the surge suppressor ground wire.

6. Connect a serial cable to the AEM2100

Channel 1 and Channel 2 serial ports.

7. Tighten the serial cable screws.

8. Plug the serial cable RJ-11 connectors into the

following field panel ports (Figure 1):

a. Plug Channel 1 into the RJ-11 or RJ-45

MODEM port.

b. Plug Channel 2 into the RJ-11 MMI port.

NOTE: All RJ-45 MODEM or MMI/MODEM ports

accept both 6-pin RJ-11 and 8-pin RJ-45 plugs.

Figure 1. AEM2100 Connections (Smoke Control

Installation Shown).

9. Plug the AEM2100 power pack into the field

panel service box outlet.

Boot-up takes <10s with IP Address. See Table

2 for an explanation of LED operation.

10. Secure loose wiring with cable ties and store

these instructions in the literature pocket.

The installation is now complete.

Table 2. AEM2100 LED Indicators.

LED Operation

Power/Diagnostic

(Blue)

Steady On = Power OK

Blinking 2x = No DHCP response

Blinking 2x = Setup Menu active

RX Serial 1

(Green)

Off = No data activity

Blinking = Data being received by AEM2100

channel 1 from Controller Modem port

TX Serial 1

(Yellow)

Off = No data activity

Blinking = Data being transmitted from AEM2100

channel 1 to Controller Modem port

RX Serial 2

(Green)

Off = No data activity

Blinking = Data being received by AEM2100

channel 2 from Controller MMI port

TX Serial 2

(Yellow)

Off = No data activity

Blinking = Data being transmitted from AEM2100

channel 2 to Controller MMI port

Ethernet Link

(Bi-color)

Off = No Ethernet link established

Solid Yellow = 10Mbps Ethernet link established

Solid Green = 100 Mbps Ethernet Link established

Ethernet Activity

(Bi-color)

Off = No data activity

Blinking Yellow = Half Duplex data activity

Blinking Green = Full Duplex data activity

Dieses Handbuch passt für folgende Modelle

Andere Siemens Server Handbücher

Siemens

Siemens RUGGEDCOM RS910 Bedienungsanleitung

Siemens

Siemens OZW772 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 840Di sl/840D sl Stücklistenhandbuch

Siemens

Siemens OZW672 Series Schulungshandbuch

Siemens

Siemens COM800 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RMC30 Bedienungsanleitung

Siemens

Siemens Server Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RS920W Bedienungsanleitung

Siemens

Siemens OZW772 Series Bedienungsanleitung

Siemens

Siemens OZW772 Series Schulungshandbuch

Siemens

Siemens RUGGEDCOM RS416P Bedienungsanleitung

Siemens

Siemens OZW672.01 Schulungshandbuch

Siemens

Siemens LOGO! CMR2040 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RS910W Bedienungsanleitung

Siemens

Siemens OZW672 Series Schulungshandbuch

Siemens

Siemens HiPath Xpressions Unified Messaging Bedienungsanleitung

Siemens

Siemens MK8000 MP4.30 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RS910 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Stücklistenhandbuch

Siemens

Siemens 3964R Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RS416 Bedienungsanleitung

Siemens

Siemens T1000 Bedienungsanleitung

Siemens

Siemens SENTRON 7KN POWERCENTER 3000 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung