Siemens REV15 series Bedienungsanleitung

Operating instructions Landis & Staefa REV15…

REV15… - the temperature controller that allows you to set the ideal room temperature at the time you want. There

are several switching patterns available that can be set to suit your specific needs. You can either rely on the

factory settings or make settings taillored to your personal needs.

Auto

Run

°C

Day

A1 A2 A3 A4 A5 A6

Setting slider

Changing the

setting values

Operation

Weekly mode with

3 heating periods (A 1-5) /

1 heating period (B 6-7)

Continuous

normal temperature

Continuous

economy temperature

Standby

with frost protection

Operating mode

selector

Change

between normal and

economy mode up to the

next switching point

Warmer/colder setting

valid up to the next

switching point

(increments of 0.2 ºC,

± 4 ºC max.)

Switching pattern

with time cursor

Displa

24-hour mode A

with 3 heating periods

24-hour mode B

with 1 heating period

Settin

Normal temperature

Economy temperature

Holiday period

Weekday (1=Monday / 7=Sunday)

Room temperature (measured)

Time of day

Remote operation active

(if connected)

Standby

Normal temperature Heating on

Economy temperature

Holiday mode Replace batteries

Auto A/B

1.5V ' AA'

Time

Operating mode

Auto

Run

1234567

0 6 12 18 24

B1 B2

Day Weekday

Switching times A1... A6

A1 A2 A3 A4 A5 A6

B1 B2 Switching times B1... B2

Current 24-hour mode

2225Z11E

Commissioning with quick startup

The controller is supplied with factory-set switching patterns, switching times and temperatures. To commission it,

proceed as follows:

1.5V 'AA'

1.5V 'AA' Remove the black transit tabs from the two batteries. Check to see if the battery holder is in its correct

position. The controller switches itself on.

Move the setting slider to this position. Press buttons to set the correct time of day.

Day Move the setting slider to this position. Press buttons to set the correct weekday.

(1 = Monday…7 = Sunday).

Auto

Run Move the setting slider back to position on the right, because only that position allows you to close the

cover.

Select the required operating mode with the operating mode selector.

Fold up operating instructions again, place them back into the cover and close the cover again.

Do you want to use automatic operation?

If that is the case, set the operating mode

selector to one of the following positions:

Auto A/B You use the weekly setting with automatic

changeover from three heating periods on

weekdays (A 1-5) to one heating period on

weekends (B 6-7).

AYou use the 24-hour setting Awith three

heating periods.

BYou use the 24-hour setting Bwith one

heating period.

The display shows the respective letter A or B.

Do you require continuous normal

temperature?

Move the operating mode selector to «Normal

temperature». This ensures continuous

heating to the normal temperature. The

display shows .

Do you require continuous economy

temperature?

Move the operating mode selector to

«Economy temperature». This ensures

continuous heating to the economy

temperature. The display shows .

Do you require continuous standby with frost

protection?

Move the operating mode selector to

«Standby». In that case, heating is provided

only when the room temperature falls below

the preset frost protection limit (5 °C). The

display shows .

Do you feel too warm or too cold?

°C By pressing these buttons, you increase or

decrease the actual room temperature in

increments of 0.2 °C by a maximum of ±4°C.

The display first shows the newly selected

temperature and then the actual value again.

These changes are valid only up to the

next switching point.

If, as a result of the

factory settings, you always feel either too

warm or too cold, you should readjust the

temperature or to suit your needs.

CE1B2225E / 27.01.1999 Subject to alteration Siemens Building Technologies / Landis & Staefa Division

Do you want to change the temperature level

or will you be absent for a short period of

time? When pressing this button, you change from

the current temperature level to the other. The

display shows either , when the change

was made from the economy temperature, or

, when it was made from the normal

temperature. This means you can select the

economy temperature during the time you are

absent. These changes are valid only up to

the next switching point.

Do you want to enter your own temperatures

and heating periods?

The controller has two different switching patterns A and

B which can be assigned to the respective weekday

block 1-5 / weekend block 6-7 (= Auto A/B), or the 24-

hour settings A and B.

Proceed as follows:

Use the setting slider to select the required

switching position (e.g. A1) and press

to enter the required switching

time.

All other switching positions (A2…A6

and B1…B2) are set the same way.

Select «Normal temperature» and press

to set the required value.

Select «Economy temperature» and press

to set the required value.

Auto

Run

Move the setting slider back to this position

and close the cover.

Table for entering selected values

Enter the values set by you in the following table. The

numbers already contained in the table represent

factory settings. Temp.

6.00 8.00 11.00 13.00 17.00 22.00

Switchin

times

A1 A2 A3 A4 A5 A6 B1 B2

7.00 23.00 20° C 16° C

2225Z12E

Will you go on holiday?

You can enter the duration of your holiday period. In

that case, the controller immediately switches to

economy mode and back to the selected operating

mode when the holiday period has expired. During the

holiday period, the display shows and the number of

days left.

Proceed as follows:

Move the setting slider to the holiday symbol

and press to enter the duration of

the holiday period (99 days max.).

Auto

Run

Move the setting slider back to this position

and close the cover.

If you return from your

holidays earlier than expected, reset the

holiday period to .

Do you need to change the time of day or the

weekday?

Move the setting slider to the time of day

position and press to set the

required time of day.

Day Move the setting slider to the weekday

position and press to select the

new weekday (1 = Monday…7 = Sunday).

Auto

Run

Move the setting slider back to this position

and close the cover.

Do you wish to return to the factory settings?

°C By pressing these three buttons

simultaneously, a complete reset is made,

which means that the switching times and

temperatures will be reset to their default

values. Caution: All individual settings will

be lost! At the same time, a display check is

made, which looks as follows:

1234567

0 6 12 18 24

2225Z13

Does the symbol appear in the display?

If this symbol appears, you need to replace the batteries

within the next three months.

Do you want to change the batteries?

• Get two new alcaline batteries type AA, 1.5 V.

• Remove the battery holder, then the batteries, insert

the new batteries and replace the battery holder.

Caution: The setting data are maintained for a

maximum of one minute only!

• Make certain the old batteries are disposed of

properly, in compliance with environmental

requirements.

Energy saving tips without sacrificing comfort

• Never allow room temperatures to exceed 21 °C.

• Press to change to economy temperature,

even if you are absent for short periods of time only.

• Air out the rooms for short periods of time only, but

properly, with the windows wide open.

Auxiliary functions

Your room temperature controller provides a number of

auxiliary functions, but these should only be set by your

heating engineer.

Andere Siemens Temperaturregler Handbücher

Siemens

Siemens RDU20U Bedienungsanleitung

Siemens

Siemens REA23.03RF Bedienungsanleitung

Siemens

Siemens RDE10.1DHW Bedienungsanleitung

Siemens

Siemens HEATWELL RDE Series Bedienerhandbuch

Siemens

Siemens RDX42.22U Betriebsanleitung

Siemens

Siemens RDF110 Bedienungsanleitung

Siemens

Siemens RDE10.1DHW Bedienungsanleitung

Siemens

Siemens QAA2290.EWSC Bedienungsanleitung

Siemens

Siemens RLA162 Bedienungsanleitung

Siemens

Siemens SITRANS TS100 Administratorhandbuch

Siemens

Siemens Landis & Staefa RAV12 Series Bedienungsanleitung

Siemens

Siemens Landis & Staefa REV11 Series Bedienungsanleitung

Siemens

Siemens KIT911 Gebrauchsanweisung

Siemens

Siemens RDF30U Betriebsanleitung

Siemens

Siemens SITRANS TS Series Bedienungsanleitung

Siemens

Siemens REV23.03RF Bedienungsanleitung

Siemens

Siemens REV23 Bedienungsanleitung

Siemens

Siemens UP 237K Bedienungsanleitung

Siemens

Siemens REA23.03RF Bedienungsanleitung

Siemens

Siemens RDE10 Series Bedienungsanleitung

Siemens

Siemens AQR2531 Series Bedienungsanleitung

Siemens

Siemens RLE132 Bedienungsanleitung

Siemens

Siemens 2000 Series Bedienungsanleitung

Siemens

Siemens 5TC9774-4 Series Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema