Siemens REV24RF Montageanleitung

CE1N2206en

24.04.2008 Building Technologies

2206

REV24RF.. RCR10/868

Radio set with 7-day

room temperature

controller REV24RF../SET

Comprising a room temperature controller (with integrated radio transmitter)

and receiver with relay outputs

•Mains-independent, battery-operated room temperature controller featuring

user-friendly operation, easy-to-read display and large numbers.

•Self-learning two-position controller with PID response (patented).

•Operating mode selection:

- 7-day automatic mode with max. 3 heating or cooling phases.

- Continuous comfort mode.

- Continuous energy saving mode.

- Protection against frost or overheating.

- Exception day (24 hour operation) with max. 3 heating or cooling phases.

•A separate temperature setpoint can be entered in automatic mode and for

the exception day for each heating or cooling phase.

•Heating zone control.

•Possibility to control cooling equipment.

•Advantage for retrofitting, renovating, and reconstruction purposes

(completely wireless room unit).

Use

Room temperature control in:

•Single-family and vacation homes.

•Apartments and offices.

•Individual rooms and professional office facilities.

•Commercially used spaces.

Control for the following equipment:

•Magnetic valves of an instantaneous water heater.

2 / 18

Siemens Room temperature controller radio set REV24RF../SET CE1N2206en

Building Technologies 24.04.2008

•Magnetic valves of an atmospheric gas burner.

•Forced draught gas and oil burners.

•Electrothermal actuators.

•Circulating pumps in heating systems.

•Electric direct heating.

•Fans of electric storage heaters.

•Zone valves (normally open and normally closed).

•Air conditioning and cooling equipment.

Function

•Bidirectional radio transmission.

•PID control with self-learning or selectable switching cycle time.

•2-point control.

•7-day time switch.

•Preselected 24-hour operating modes.

•Override function.

•Holiday mode.

•Party mode.

•Protection function (protection against frost or overheating).

•Information level to check settings.

•Reset function.

•Sensor calibration.

•Heating or cooling.

•Minimum limitation of setpoint.

•Periodic pump run.

Protection against valve seizure.

•Optimum start control in the morning (P.1).

•Synchronization to radio time signal from Frankfurt, Germany (REV24RFDC).

•Manual override of the receiving relay.

Type summary

Radio set comprising:

- Room temperature controller REV24RF with 7-day time switch,

Base and receiver RCR10/868 REV24RF/SET

Radio set comprising

- Room temperature controller REV24RFDC with 7-day time switch,

Receiver for time signal from Frankfurt, Germany (DCF77),

Base and receiver RCR10/868 REV24RFDC/SET

Ordering

Please indicate the type number as per the "Type summary" when ordering.

Delivery

The controller/transmitter REV24RF.. is delivered with batteries.

Mechanical design

Plastic casing with an easy-to-read display and large numbers, easily accessible

operating elements, and removable base. The casing accommodates the electronics

with the DIP switches. The easily accessible battery compartment allows for easy

exchange of two 1.5 V alkaline batteries, type AA.

The base helps attach the room controller to the wall. The supplied table stand allows

you to stand the controller anywhere in the room. You can manually attach the table

stand without tools.

Room controller and

base

Base and

table stand

3 / 18

Siemens Room temperature controller radio set REV24RF../SET CE1N2206en

Building Technologies 24.04.2008

Plastic housing with large operating elements, removable cover and easily accessible

terminal block with lots of space to attach the wires. You can mount and wire the unit on

most commercially available recessed conduit boxes or directly on the wall. The

potential-free changeover contact and the antenna for reception are integrated in the

unit.

1Display

Change battery Time of day

Alarm Room temperature (measured)

Heating mode Clear text display line

(max. 18 spaces)

Cooling mode

Weekday (max. 3 spaces)

0 4 8 12 16 20 24

24 hour timeframe with

switching pattern with flashing

time cursor

Info Info

Setpoint for comfort mode

Weekday block

Weekend block

Weekday

Setpoint for absence hTime unit

Room temperature

Absence/holiday mode set

Setpoint for frost protection

mode Absence/holiday mode active

Without language selection

Energy saving mode setpoint Party mode active

Time signal from Frankfurt °C / °F Temperature unit °C or °F

Date (day - month - year) Heating/cooling/pump on

Receiver

Display and operating

elements

4 / 18

Siemens Room temperature controller radio set REV24RF../SET CE1N2206en

Building Technologies 24.04.2008

2Operating mode selector

Automatic weekly mode with max. three heating or cooling phases per

day.

Exception day with max. three heating or cooling phases.

Continuous comfort mode (= continuous comfort temperature).

Continuous energy saving mode (= continuous energy saving

temperature).

Protection mode (protection against frost or overheating).

3INFO

Pressing the Info button once illuminates the display. Illumination

automatically turns off after a short period of time.

Pressing the Info button again activates the information display: is lit.

The unit first displays queued error messages followed by important

information (e.g. time switch programs, etc.).

4Plus button

Increase values, set time, or make a selection.

5Override button / party mode

In the time switch program, this button allows you to quickly change from the

active temperature level to the next and back.

Thus, you can quickly change to energy saving temperature when you leave

the apartment for a short period of time, thus saving energy.

The display indicates the change. It is valid only until the next switching time.

ty mode: Press the button for 3 seconds.

Party mode is available only in operating modes and . In party mode,

the controller controls to a freely selectable temperature for a freely

selectable period of time.

In party mode, symbol is displayed along with the end of party mode.

6Minus button

Decrease values, set time, or make a selection.

5 / 18

Siemens Room temperature controller radio set REV24RF../SET CE1N2206en

Building Technologies 24.04.2008

7Program selection slider

Time

Day – Month – Year (2 spaces for day, month, and year).

Weekday, weekend, or individual day blocks.

1, 2, or 3 comfort phases.

Start

Comfort phase 1

Start

Comfort phase 2

Start

Comfort phase 3

Setpoint

Comfort phase 1

Setpoint

Comfort phase 2

Setpoint

Comfort phase 3

End

Comfort phase 1

End

Comfort phase 2

End

Comfort phase 3

Energy saving temperature in the automatic mode and exception day time

switch programs.

Start of absence.

Temperature setpoint during absence.

End of absence.

RUN Slider position RUN allows for closing the cover.

Operating modes

The controller offers the two time switch programs and .

Enter a start time and end time for each comfort phase. Also comfort temperature

setpoint can be freely entered for each comfort phase. Between the comfort phases

the controller always switches to the same, freely selectable energy saving

temperature setpoint.

2205Z04

°C

06 08 18 22 h

Heating

phase 1

12 14

Heating

phase 2

Heating phase 3

The controller also offers the three 3 continuous modes comfort mode,

energy saving mode and frost protection mode.

Operation with

time switch program

Example with

3 heating phases

Continuous operating

modes

6 / 18

Siemens Room temperature controller radio set REV24RF../SET CE1N2206en

Building Technologies 24.04.2008

You can freely adjust the setpoints for the weekly and 24-hour operating modes.

Setting range for all setpoints without setpoint limitation 3…35 °C.

Setting range for all setpoints with setpoint limitation 16…35 °C.

Factory setting for heating Factory setting for cooling

, , , 20 °C 24 °C

, 16 °C 28 °C

8 °C 35 °C

12 °C 30 °C

Factory settings: Switching times

Comfort phases P1 P2 P3 P4 P5 P6

1. 07:00 23:00 PASS PASS PASS PASS

2. 06:00 08:00 17:00 22:00 PASS PASS

3. 06:00 08:00 11:00 13:00 17:00 22:00

Three different switching patterns are available to simplify entry of switching times. These

can be assigned as blocks to the corresponding weekdays 1…5 and weekend days

6…7. As a result, you need to adapt the switching times and room temperatures only

once for each block.

Switching pattern Blocks

You can also enter individual days … .

You can enter the beginning, temperature and end of your holidays. At the beginning of

the holidays, the controller switches to the desired holiday temperature and returns to the

previously set operating mode at the end of the holidays.

In holiday mode, symbol is displayed along with the end of holiday mode.

Proceed as follows to enter your settings:

Set slider to position 15 (start of absence): Press or to set the start date

for your holidays.

Set slider to position 16 (temperature during absence): Press or to set

the desired temperature while on holidays.

Set slider to position 17 (end of absence): Press or to set the end date

for your holidays.

RUN

Return the slider to position RUN. Symbol is displayed to the left of the

symbol.

Press , , , or move the slider to end holiday mode prematurely.

Setpoints

Factory setting

7-day time switch

Enter holidays or

absences

7 / 18

Siemens Room temperature controller radio set REV24RF../SET CE1N2206en

Building Technologies 24.04.2008

Technical features

DIP switches

DIP switch ON / OFF 1 2 3 4 5 6 7 8 9 10

Sensor calibration On

Periodic pump run and

anti-lime function On

Sensor calibration Off

Periodic pump run and

anti-lime function Off

Setpoint limitation 16…35 °C

Start optimization: 1 h/°C

Setpoint limitation 3…35 °C

Start optimization: ¼ h/°C

Temperature display °F

Start optimization: ½ h/°C

Temperature display °C

Start optimization: Off

PID self-learning (Op. mode: Cooling)

PID 6 (Op. mode: Heating)

PID12 Quartz

2-point

Radio clock

DIP switch reset

1342

2211Z32

56789

After you change one or several DIP switch positions, you must press the DIP switch reset button to reset the DIP

switch. Otherwise, the previous setting remains active!

Factory setting: All DIP switches to OFF

If the displayed room temperature does not match the measured room temperature, the

temperature sensor can be recalibrated.

Set DIP switch to ON and press the DIP switch reset button:

CAL symbol is displayed. The currently measured temperature flashes.

Press or to recalibrate by max. ± 5 °C.

Set DIP switch to OFF and press the DIP switch reset button to save the settings.

The minimum setpoint limitation of 16 °C prevents undesired heat transfer to neighboring

spaces in buildings featuring several heating zones.

DIP switch ON: Setpoint limitation 16…35 °C.

DIP switch OFF: Setpoint limitation 3…35 °C (factory setting).

Press the DIP switch reset button to save the settings.

DIP switch ON: Temperature display in °F.

DIP switch OFF: Temperature display in °C (factory setting).

Press the DIP switch reset button to save the settings.

The REV24… is a two-position controller with PID control. The room temperature is

controlled through cyclic switching of an actuating unit.

DIP switches 4 ON and 5 ON: PID self-learning

Adaptive control for all applications.

DIP switches 4 ON and 5 OFF: PID 6

Fast controlled system for applications in locations with

large temperature deviations.

DIP switches 4 OFF and 5 ON: PID 12

Normal controlled system for applications in locations with

normal temperature deviations.

DIP switches 4 OFF and 5 OFF: 2-point

ASensor calibration:

DIP switch 1

BSetpoint limitation:

DIP switch 2

CTemperature display in

°C or °F:

DIP switch 3

DControl behavior:

DIP switches 4 and 5

8 / 18

Siemens Room temperature controller radio set REV24RF../SET CE1N2206en

Building Technologies 24.04.2008

For complex controlled systems, simple two-position controller with

0.5 °C switching difference (factory setting).

Press the DIP switch reset button to save the settings.

Only applicable with controlled circulating pump or valve!

This function protects the pump or valve during extended OFF periods against possible

seizure caused by liming. Periodic pump run is activated every 24 hours at 12 p.m. for

three minutes (symbol ▲is displayed during active pump run).

DIP switch ON: Pump run On.

DIP switch OFF: Pump run On (factory setting).

Press the DIP switch reset button to save the settings.

Optimization advances the switch-on point P.1 to ensure that the selected setpoint is

reached at the desired time. The setting depends on the controlled system, i.e., on heat

transmission (piping system, radiators), building dynamics (building mass, insulation),

and heat output (boiler capacity, flow temperature).

DIP switches 7 ON and 8 ON: 1 h/°C For slow controlled systems.

DIP switches 7 ON and 8 OFF: ¼ h/°C For fast controlled systems.

DIP switches 7 OFF and 8 ON: ½ h/°C For medium controlled systems.

DIP switches 7 OFF and 8 OFF: OFF Off, no effect (factory setting).

Press the DIP switch reset button to save the settings.

- 4 - 2

2254D01

- 3

1/4h/°C

1/2h/°C

1h/°C P.1

- 2 - 1 - ½

- 1½

- 1 - ½ - ¼

- ¾

Pon

°C T1

- 1 h

TRx

Key for diagram:

T Temperature (°C)

t Forward shift of switch-on point (h)

TRx Room temperature actual value

Pon Starting point for optimized heat-up time.

The controller can be switched over for cooling applications on DIP switch 9.

DIP switch 9 ON: Cooling

DIP switch 9 OFF: Heating (factory setting).

Press the DIP switch reset button to save the settings.

Only applicable to REV..DC (with integrated DCF77 receiver to receive time signal from

Frankfurt, Germany)!

DIP switch ON: Clock run by controller-internal quartz.

DIP switch OFF: Time signal DCF77 from Frankfurt, Germany.

Press the DIP switch reset button to save the settings.

During startup, REV..DC synchronizes automatically to the time signal (DCF77) from

Frankfurt, Germany. Synchronization takes max. 10 minutes. Synchronization restarts

each time you press the button or move the program selection slider from the RUN

position during these 10 minutes. Siemens recommends to set the desired settings upon

startup, install the REV..DC in the desired location, and not carry out any actions on the

REV..DC for the next 10 minutes.

In normal operation, the REV..DC synchronizes to the radio clock every day at 3:10 a.m.

EPeriodic pump run

and anti-lime function:

DIP switch 6

FStart optimization:

DIP switches 7 and 8

GOperating mode heating

or cooling:

DIP switch 9

HRadio clock:

DIP switch 10

Note

on synchronization

9 / 18

Siemens Room temperature controller radio set REV24RF../SET CE1N2206en

Building Technologies 24.04.2008

The time signal from Frankfurt is modulated to a radio signal. The reception of this radio

signal depends on the distance to Frankfurt, atmospheric conditions as well as the

location where the REV..DC is installed. Siemens cannot guarantee that the REV..DC

can receive the time signal from Frankfurt at any time and any place.

The radio clock symbol is deactivated and an error message is displayed if the clock was not

able to synchronize the time for 7 consecutive days. The controller then runs on the internal

quartz.

After you change one or several DIP switch positions, you must press the DIP switch

reset button to reset the DIP switch.

Otherwise, the previous setting remains active!

Access to the expert level

Set the program selection slider to RUN. Press and simultaneously for 3 seconds, release the buttons, and

within 3 seconds press and hold down and simultaneously for 3 seconds, release , and press for another 3

seconds. This releases the engineering settings. is displayed.

The display first shows language selection with Code 00. Press the buttons or to navigate the settings.

Confirm settings by pressing .

Press the operating mode selector to exit the engineering settings.

Code list

This entry has no effect if the radio clock either is inactive or not available.

The time signal received from Frankfurt is shifted by the value set in Code 30 (time zone)

if the radio clock is active.

The time is always changed over at 2 a.m. on the Sunday preceding the set date if there

is no radio clock or if it is inactive. The time change is shifted by the value set in Code 30

(time zone) when the radio clock is active.

The time is always changed over at 3 a.m. on the Sunday preceding the set date if there

is no radio clock or if it is inactive.

Functional check

a) Check the display. If there is no display, check insertion and function of the batteries.

b) Operating mode “Continuous comfort mode“ , read displayed temperature.

c) REV.. in heating mode: Set the temperature setpoint higher than the displayed room

temperature (see operating instructions).

REV.. in cooling mode: Set the temperature setpoint lower than the displayed room

temperature (see operating instructions).

Note

on reception

No reception

JDIP switch reset

1342

2211Z32

56789

Function block Code Name Factory setting Your setting

00 Language English

01 Sensor calibration off

Basic settings

02 Switching differential 2-point 0.5 °C

10 Illumination time 10 seconds

11 Background brightness 0

LCD

optimization 12 Contrast 0

Time zone

Deviation from time signal in Frankfurt

(Central European Time CET) (see Note 1)

0 hours

31 Start of daylight saving time (see Note 2) March 31 (03-31)

Clock settings

32 End of daylight saving time (see Note 3) October 31 (10-31)

Note 1:

Note 2:

Note 3:

10 / 18

Siemens Room temperature controller radio set REV24RF../SET CE1N2206en

Building Technologies 24.04.2008

d) The relay and, as a result, the actuating device must switch at the latest after one minute.

Symbol ▲is displayed. If not displayed:

•Check actuating device and wiring.

•It is possible that in heating mode the room temperature is higher than the set

temperature setpoint (and lower for cooling mode).

e) Set the temperature setpoint for operating mode “Continuous comfort mode“ to the

desired value.

f) Select the desired operating mode.

Reset

User-defined settings:

, and simultaneously for 3 seconds:

This resets all temperature and time settings of the program selection slider to default

values (see also "Factory settings" in the operating instructions). The expert settings

remain unchanged.

The clock starts at 12 p.m., the date on 01-01-08 (01 January 2008).

During the reset, all display fields are lit and can be checked accordingly.

All user-defined settings plus expert settings:

Press the DIP switch reset button

1342

2211Z32

56789

, and simultaneously for 5

seconds:

After the reset, all factor settings are reloaded. This applies to the program selection

slider as well as to the expert settings.

Simultaneously press the "Test and "Learn" buttons on the rear of the REV24RF.. for

1 second. This deletes all data saved from the receivers listed as faulty in Info mode.

After this reset, the REV24RF.. indicates that all faulty receivers were deleted.

Simultaneously press the "Test and "Learn" buttons on the rear of the REV24RF.. for

5 seconds. This deletes the data saved from all receivers.

After this reset, the REV24RF.. indicates that no more receivers are connected to the room

controller.

Open the RCR10/886 cover. Simultaneously press the "Learn" and override buttons on the

front of the RCR10/868 for 4 seconds. This deletes the data saved from the room controller.

LED_1 flashes red. This indicates that no room controller is connected to the receiver.

Engineering

•Place the room unit in the main living room by considering the following aspects (wall

mounting or free placement using stand).

•The distance to the receiver may not exceed 20 meters or 2 floors.

•Choose the place of installation so that the sensor can capture the air temperature in

the room as accurately as possible without being adversely affected by direct solar

radiation or other heat or cooling sources (about 1.5 meters above the floor for wall

mounting).

Room controller

REV24RF..:

Temperature controller

data

Room controller

REV24RF..:

Data from faulty

receivers

Room controller

REV24RF..:

Data from all receivers

Receiver RCR10/868:

Data from the room

controller

Room controller

REV24RF..:

Andere Handbücher für REV24RF

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Temperaturregler Handbücher

Siemens

Siemens REA23 Bedienungsanleitung

Siemens

Siemens RDX Series Bedienungsanleitung

Siemens

Siemens POS8.4420/109 Bedienungsanleitung

Siemens

Siemens SITRANS T Series Administratorhandbuch

Siemens

Siemens RLM162 Bedienungsanleitung

Siemens

Siemens i-system UP 237K Service-Handbuch

Siemens

Siemens RDF20U Bedienungsanleitung

Siemens

Siemens SITRANS TS100 Administratorhandbuch

Siemens

Siemens QAX910 Bedienungsanleitung

Siemens

Siemens RLE132 Bedienungsanleitung

Siemens

Siemens QAA73 Bedienungsanleitung

Siemens

Siemens RLE132 Bedienungsanleitung

Siemens

Siemens Landis & Staefa RAV12 Series Bedienungsanleitung

Siemens

Siemens Synco 900 Leitfaden

Siemens

Siemens 1000 series Bedienungsanleitung

Siemens

Siemens AQR2531 Series Bedienungsanleitung

Siemens

Siemens QAX32.1 Bedienungsanleitung

Siemens

Siemens 2000 Series Bedienungsanleitung

Siemens

Siemens RDJ10RF/SET Bedienungsanleitung

Siemens

Siemens SITRANS TS Series Bedienungsanleitung

Siemens

Siemens SITRANS TSinse rt Administratorhandbuch

Siemens

Siemens REV23.03RF Bedienungsanleitung

Siemens

Siemens QAA70 Bedienungsanleitung

Siemens

Siemens RDE10.1DHW Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema

Opt Lasers

Opt Lasers TEC-8A-24V-PID-HC Bedienungsanleitung

Vaillant

Vaillant VR 92/3 Bedienungsanleitung