Siemens DT-11 Montage- und Bedienungsanleitung

These instructions are written in accordance with the

installation guidelines of NFPA No. 72, National Fire

Alarm Code, and CAN/ULC-S524, The Installation of Fire

Alarm Systems.

CAUTION

Detection Device Storage

DO NOT install this detection device until all

construction is completed.

DO NOT store this detection device where it can

be contaminated by dirt, dust, or humidity.

DETECTOR PLACEMENT

Locate the DT-11 on the ceiling, at least 4 inches from

the side walls. For an ideal, smooth ceiling condition,

place the detectors at a maximum center spacing of

50 feet (2500 square feet), 25 feet from side walls or

room partitions. For FM Approved installations this

detector has an RTI rating of QUICK, which allows a

maximum center spacing of 20 feet (400 square feet).

Locate detectors 10 feet from side walls or room

partitions.

Actual job conditions and sound engineering judgment

to determine detector spacing. Consider environ-

mental factors including ambient temperature fluctua-

tion, and the nature of the fire hazard. Room or area

configuration and ceiling type (sloped or flat, smooth

or beamed) also dictates placement.

Should questions arise regarding detector placement,

follow the drawings provided and/or approved by

Siemens Industry, Inc., or by its authorized distributors.

This is extremely important! The detector placements

shown on these drawings were chosen after a careful

evaluation of the area being protected. Siemens

Industry, Inc.'s extensive experience in design of the

system assures the best detector placement by

following these drawings.

Installation/Wiring Instructions

Model DT-11 Thermal Detector

SPECIFICATIONS

Environmental

Temperature: 32OF (0OC) to 100OF (38OC).

Humidity: Up to 93% RH, non condensing

Air Pressure: No effect.

Alarm Temp: 135OF (57OC)

Electrical

Voltage: 16-27 VDC

Ripple: 3V peak-to-peak

Supervisory Current: 110μA max

Alarm Current: 33-50mA

Start-up Time: 50 seconds max

DETECTOR WIRING

The DT-11 should be connected as shown in Figure 1

using the separate mounting base, Model DB-11.

Follow the control panel wiring connection drawing

installed on the inside face of each control panel cover.

See DB-11 instruction, P/N 315-094193, for base

mounting. Duplicate wiring information is also in the

Installation, Operation, and Maintenance Manual

provided with every control panel. Note any

limitations on the number of detectors and

restrictions on the use of remote devices

permitted for each circuit.

INSTALLATION / REMOVAL OF DETECTOR

TO INSTALL:

• Align LED in detector with LED symbol on base

and insert detector into base.

• Rotate detector counterclockwise while gently

pressing on it until the detector drops fully into base.

• Then rotate the detector clockwise until it stops and

locks in place. Insert optional locking screw (Order

Model LK-11).

TO REMOVE:

Loosen locking screw, if installed. Then rotate the

detector counterclockwise until stop is reached. Pull

detector out of base.

P/N 315-095429-5

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

LED INDICATOR OPERATION

The DT-11 contains an LED indicator capable of

flashing either one of three distinct colors: green,

yellow, or red. Every seven seconds, the

microprocessor-based detector checks that its critical

electronics are operating.

Based on the results of these checks, the LED

indicator flashes as follows:

hsalF

roloCnoitidnoC

hsalF

lavretnI

)sdnoceS(

neerG.noitarepoyrosivrepuslamroN7

wolleY

)riaper(ecivresseriuqerr

otceteD

stidnoyebgnitareposiro

.snoitacificepslatnemnorivne

0-7

deRmralA½2

sehsalF

ro,derewoptonsirotceteD

.riaperseriuqer -

TESTING AND MAINTENANCE

TEST

Testing requires no test equipment. A green flash of

the detector LED about every seven seconds

indicates that the DT-11 is operating properly. The

minimum test schedule may be found in the current

edition of NFPA 72, Chapter 7 for installations in the

U.S., and CAN/ULC-S537, The Verification of Fire

Alarm Systems, for installations in Canada.

END OF

LINE

DEVICE

(NOTE

POLARITY

WHEN

APPLICABLE)

1a 1b

1b 1b

DB-11

[WITH REMOTE DEVICE(S)]

TO INITIATING

CIRCUIT OF

SIEMENS

INDUSTRY, INC.

CONTROL PANEL

(SEE CAUTION 1)

MULTIPLE REMOTE DEVICES

SEE REMOTE DEVICE INSTRUCTIONS

FOR WIRING DETAILS:

each detector/base may have up to 2 remote devices

with the following configurations and restrictions only:

If remote devices are supported by the initiating circuit,

DEVICE

RR-11

RLC-11, RLW-11

RSAC-11, RSAW-11

ADB-11

Device 1

Remote

RR-11

RLC-11, RLW-11

Device 2

Remote

RLC-11, RLW-11

RSAC-11, RSAW-11

RLC-11, RLW-11

Restrictions

See Caution 2

Wire from base to

RSAC-11/RSAW-11

to RL-11

INSTRUCTIONS

INSTALLATION

P/N 315-094924

P/N 315-094925

P/N 315-094926

P/N 315-096162

DB-11

[NO REMOTE DEVICE]

Figure 1 Installation and Wiring Diagram for Conventional Detector

CAUTION:

1. Do not use looped wire under base

terminal 5. Break wire run to provide

supervision of connection.

2. When a remote relay is used to

control a critical system function,

therelayanditsassociateddetector

and optional module(s) must be the

ONLY devices on the initiating

circuit.

CAUTION: UNDER NO CIRCUMSTANCES

IS THE DETECTOR HEAD TO BE DISASSEMBLED.

NO FIELD REPAIRS SHOULD BE ATTEMPTED. THE

DETECTORS ARE FACTORY REPAIRABLE ONLY.

DO NOT PAINT

The detector/base plastic is marked DO NOT PAINT.

This is intended to prohibit painting during routine

maintenance of the occupancy which can affect

proper operation of the detector.

TNEMPIUQELORTNOCELBITAPMOC tnempiuqE reifitnedIytilibitapmoC gniriW/noitallatsnI snoitcurtsnI

)metsySSLX-r

edniFeriF(4-CDC5-002430-513N/P

RE2-PC5-325390-513N/P

)3metsyS(53-PC52-209480-513N/P

)metsySQI-LXM/LXM(1-MZC8-527090-513N/P

)metsySQI-LXM/LXM(6B1-MZC8-553590-513N/P

)metsySQI-LXM/LXM(4-MZC21-627090-513N/P

)metsySSLX-rednIFeriF(MZ

H5-058430-513N/P

)metsyS052-SF(MZH5-058430-513N/P

LXP4-131490-513N/P

)LXP(D4-CZP3-461490-513N/P

)LXP(B4-EZP5-5

60490-513N/P

LXS01-914290-513N/P

XE-LXS8-799590-513N/P

)LXS(R4-EZS4-034290-513N/P

)XE-LXS(X4-EZS7-810690-513N/P

)XE-LXS(XA8-EZS7-220690-513N/P

)3metsyS(53-UZ71-222

380-513N/P

reifitnediytilibitapmocehtsirebmunledomrotcetedehT.

etomertroppustonseodtnempiuqelortnoC seirossecca.syalerrospmal.g.e; .seludomXNZ3-LXhtiwesuroftonsi11-TD:

etoN

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Canada Limited

Building Technologies Division

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

P/N 315-095429-5

Andere Siemens Temperaturregler Handbücher

Siemens

Siemens AQR2531 Series Bedienungsanleitung

Siemens

Siemens RVL482 Bedienungsanleitung

Siemens

Siemens REV23.03RF Bedienungsanleitung

Siemens

Siemens SITRANS TSinse rt Administratorhandbuch

Siemens

Siemens QAX910 Bedienungsanleitung

Siemens

Siemens QAA73 Bedienungsanleitung

Siemens

Siemens TALON Bedienungsanleitung

Siemens

Siemens RDU50U Betriebsanleitung

Siemens

Siemens Free Energy Band RCU61U Betriebsanleitung

Siemens

Siemens 24RFDC/SET Bedienungsanleitung

Siemens

Siemens REV23 Bedienungsanleitung

Siemens

Siemens REV24RF Bedienungsanleitung

Siemens

Siemens SITRANS Series Administratorhandbuch

Siemens

Siemens REV15 series Bedienungsanleitung

Siemens

Siemens RDX33 Series Bedienungsanleitung

Siemens

Siemens REV23 Bedienungsanleitung

Siemens

Siemens QMX3.P37 Bedienungsanleitung

Siemens

Siemens POS8.4420/109 Bedienungsanleitung

Siemens

Siemens HZ39050 Bedienungsanleitung

Siemens

Siemens REV24RF Montageanleitung

Siemens

Siemens REV23 Bedienungsanleitung

Siemens

Siemens SITRANS TS100 Administratorhandbuch

Siemens

Siemens REA22 Bedienerhandbuch

Siemens

Siemens QAA2290.EWSC Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema

Opt Lasers

Opt Lasers TEC-8A-24V-PID-HC Bedienungsanleitung

Vaillant

Vaillant VR 92/3 Bedienungsanleitung