SIGMA TEK DI 204 Bedienungsanleitung

DI 204

S-DIAS Digital Input Module

with 2 Incremental Encoder Inputs

Instruction Manual

Date of creation: 19.11.2013

Version date: 26.07.2023

Article number: 20-006-204-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS DIGITAL INPUT MODULE DI 204

26.07.2023 Page 1

S-DIAS Digital Input Module with

2 Incremental Encoder Inputs DI 204

with 14 digital inputs

2 Incremental encoder inputs

The S-DIAS digital input module DI 204 is equipped with two incremental

inputs with a TTL signal and 14 inputs with a +24 V signal for reading the

signal states “0“ and “1“. To suppress noise in the signal lines, input filters

are provided. The incremental encoder values can be latched.

DI 204 S-DIAS DIGITAL INPUT MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 5 
1.1 Target Group/Purpose of this Operating Manual......................5 
1.2 Important Reference Documentation .........................................5 
1.3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
2.1 Symbols Used...............................................................................6 
2.2 Disclaimer......................................................................................8 
2.3 General Safety Directives ............................................................9 
2.4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
3.1 Directives.....................................................................................11 
3.1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12 
5Technical Data .......................................................................13 
5.1 Incremental Encoder Input Specifications...............................13 
5.2 Input Specifications....................................................................13 
5.3 Electrical Requirements.............................................................13 
5.4 Miscellaneous .............................................................................15 
5.5 Environmental Conditions.........................................................15 
6Mechanical Dimensions........................................................16 

 S-DIAS DIGITAL INPUT MODULE DI 204 
 
07.2023 Page 3 
7Connector Layout..................................................................17 
1 Status LEDs.................................................................................17 
2 Applicable Connectors...............................................................18 
3 Label Field...................................................................................19 
8Wiring.....................................................................................20 
1 Wiring Example...........................................................................20 
2 Note..............................................................................................21 
9Assembly/Installation ...........................................................22 
1 Check Contents of Delivery.......................................................22 
2 Mounting......................................................................................23 
Addressing.............................................................................25 
1 Address mapping overview.......................................................25 
Supported Cycle Times ........................................................27 
1 Cycle Times below 1 ms (in µs).................................................27 
2 Cycle Times equal to or higher than 1 ms (in ms)...................27 
Transport/Storage .................................................................28 
Storage...................................................................................28 
Maintenance...........................................................................29 
1 Service.........................................................................................29 
2 Repair...........................................................................................29 

DI 204 S-DIAS DIGITAL INPUT MODULE

Page 4 26.07.2023

15 Disposal..................................................................................29

16 Hardware Class DI204 ...........................................................30

16.1 Interfaces.....................................................................................31

16.1.1 General..............................................................................................31

16.1.2 Digital Inputs......................................................................................32

16.1.3 Encoder.............................................................................................33

16.1.4 Communication Interfaces.................................................................33

16.2 Example.......................................................................................34

S-DIAS DIGITAL INPUT MODULE DI 204

26.07.2023 Page 5

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x DI 204

DI 204 S-DIAS DIGITAL INPUT MODULE

Page 6 26.07.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS DIGITAL INPUT MODULE DI 204

26.07.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

DI 204 S-DIAS DIGITAL INPUT MODULE

Page 8 26.07.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product

description. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Inhaltsverzeichnis

Andere SIGMA TEK E/A-System Handbücher

SIGMA TEK

SIGMA TEK DI 160 Bedienungsanleitung

SIGMA TEK

SIGMA TEK IPN 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AO 026 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SRO 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK TO 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SDI 101 Bedienungsanleitung

SIGMA TEK

SIGMA TEK FC 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SDI 101 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AO 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DI 200 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 075 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DM 811 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 088-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 040 Bedienungsanleitung

SIGMA TEK

SIGMA TEK TO 127 Bedienungsanleitung

SIGMA TEK

SIGMA TEK C-DIAS Series Bedienungsanleitung

SIGMA TEK

SIGMA TEK DI 080 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CSTO 082 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 046 Bedienungsanleitung

SIGMA TEK

SIGMA TEK IO 011S Bedienungsanleitung

SIGMA TEK

SIGMA TEK C-DIAS Gebrauchsanweisung

SIGMA TEK

SIGMA TEK CP 931 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CO 041 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DM 822 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung