SIGMA TEK ETT 1064 Bedienungsanleitung
Date of creation: 16.12.2021 Version date: 28.03.2022 Article number: 01-230-1064-E
ETT 1064
Multi-touch Operating Panel
Operating Manual
Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: +43/6274/4321
Fax: +43/6274/4321-18
Email: [email protected]
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2021
SIGMATEK GmbH & Co KG
Translation from German
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or
distributed in any form (print, photocopy, microfilm or in any other process) without express permission.
We reserve the right to make changes in the content without notice. SIGMATEK GmbH & Co KG is not responsible
for technical or printing errors in this handbook and assumes no responsibility for damages that occur through
its use.
MULTI-TOUCH OPERATING PANEL ETT 1064
Multi-touch Operating Panel ETT 1064
The ETT 1064 is an intelligent panel for visualizing, operating and monitoring automated
processes. Process diagnostics is therewith simplified.
A projective capacitive touch screen serves as the input medium for process data and
parameters. The output is shown on a 10.1“ TFT color display.
The available interfaces can be used to exchange process data or configure the multi-touch
terminal.
28.03.2022 Page 1
ETT 1064 MULTI-TOUCH OPERATING PANEL
Table of Contents
1 Introduction 5
1.1 Target Group/Purpose of this Operating Manual 5
1.2 Important Reference Documentation 5
1.3 Contents of Delivery 5
2 Basic Safety Guidelines 6
2.1 Symbols Used 6
2.2 Disclaimer 8
2.3 General Safety Guidelines 9
2.4 Software/Training 10
3 Standards and Guidelines 11
3.1 Guidelines 11
3.1.1 EU Conformity Declaration 11
4 Technical Data 12
4.1 Performance Data 12
4.2 Electrical Requirements 13
4.3 Display 14
4.4 Control Unit 15
4.5 Minimum Distance between Operating Elements for Multi-touch Applications 16
4.6 Input 17
4.7 Environmental Conditions 17
4.8 Miscellaneous 17
5 Interfaces 18
5.1 Rear Connectors 18
5.1.1 X1: Supply (4-pin Phoenix RM 3.5) 18
5.1.2 X2, X3: Ethernet 1, 2 (10/100/1000 Mbit/s) (RJ45) 18
5.1.3 X4, X5: USB 2.0 (Type A) 19
Page 2 28.03.2022
MULTI-TOUCH OPERATING PANEL ETT 1064
5.1.4 X6: microSD 19
5.1.5 X7: USB Online OTG 2.0 (Type Mini-B) 20
5.2 Applicable Connectors 20
5.3 Status Display LEDs 21
6 Mechanical Dimensions 22
7 Assembly/Installation 23
7.1 Check Contents of Delivery 23
7.2 Installation 23
7.3 Mounting Instructions 23
7.3.1 Required Cutout for Mounting the Terminal 24
7.3.2 Mounting Position 25
7.3.3 Minimum Distance Installation 26
8 Wiring 27
8.1 Grounding 27
8.2 Shielding 27
8.3 ESD Protection 28
8.4 USB Interface 28
9 Process Diagram 29
10 Status and Error Messages 30
11 Transport/Storage 40
12 Storage 41
13 Maintenance 42
13.1 Cleaning and Disinfecting the Touch Screen 42
13.2 Service 43
13.2.1 Calibrating the Touch Screen 43
13.3 Repair 44
14 Buffer Battery 45
28.03.2022 Page 3
ETT 1064 MULTI-TOUCH OPERATING PANEL
14.1 Data Retention Battery Change 46
14.2 Exchanging the Battery 46
15 Display „Burn-In“ Effect 47
15.1 Screen Saver 47
16 Disposal 48
17 Accessories 49
17.1 Touch Pen 49
17.2 Battery 49
17.3 microSD Card 49
18 Application Information 50
18.1 Storage Media 50
Page 4 28.03.2022
MULTI-TOUCH OPERATING PANEL ETT 1064
1 Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
lProject planners
lTechnicians
lCommissioning engineers
lMachine operators
lMaintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found on
our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
lHW IP Address Settings
This and additional documents can be downloaded from our website or obtained through
support.
1.3 Contents of Delivery
1x ETT 1064
8x angle bracket
1x 4-pin Phoenix connector plug
28.03.2022 Page 5
ETT 1064 MULTI-TOUCH OPERATING PANEL
2 Basic Safety Guidelines
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes.
DANGER
Danger indicates that death or serious injury will occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
Page 6 28.03.2022
MULTI-TOUCH OPERATING PANEL ETT 1064
CAUTION
Caution indicates that moderate to slight injury can occur, if the
specified measures are not taken.
To avoid moderate to slight injuries, observe the all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
CAUTION
Danger for ESD-sensitive components.
Les signes de danger pour les composants sensibles aux décharges
électrostatiques.
INFORMATION
INFORMATION
Provides important information on the product, handling or
relevant sections of the documentation, which require particular
attention.
28.03.2022 Page 7
ETT 1064 MULTI-TOUCH OPERATING PANEL
2.2 Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual is
regularly checked and required corrections are included in the subsequent
versions. The machine manufacturer is responsible for the proper
assembly, as well as device configuration. The machine operator is
responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If necessary,
contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product description. It
does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this operating
manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused
through, non-compliance with these instructions or applicable
regulations.
Page 8 28.03.2022
Inhaltsverzeichnis
Andere SIGMA TEK Touchscreen Handbücher
SIGMA TEK
SIGMA TEK HGW 1033-01 Bedienungsanleitung
SIGMA TEK
SIGMA TEK HGW 1033-3 Bedienungsanleitung
SIGMA TEK
SIGMA TEK ETT 764 Bedienungsanleitung
SIGMA TEK
SIGMA TEK ETT 412 Bedienungsanleitung
SIGMA TEK
SIGMA TEK HZS 771 Bedienungsanleitung
SIGMA TEK
SIGMA TEK ETT 1962 Bedienungsanleitung
SIGMA TEK
SIGMA TEK ETT 1264 Bedienungsanleitung
Beliebte Touchscreen Handbücher anderer Marken
IBASE Technology
IBASE Technology ASTUT-152-RE1S Bedienungsanleitung
YASKAWA
YASKAWA TP 610C Bedienungsanleitung
B&R
B&R Power Panel C Series Bedienungsanleitung
Beijer Electronics
Beijer Electronics X2 control Bedienungsanleitung
AXIOMTEK
AXIOMTEK GOT321W-521 Bedienungsanleitung
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Bedienungsanleitung
