Signature UPSXB2627 Series Bedienungsanleitung

Installation Guide

BUILT-IN SXS REFRIGERATOR

UPSXB2627**

www.thesignaturekitchen.com

Contents

1. Precaution before installation ................................................................. 3

2. Product and Cutout dimension ............................................................... 4

3. Precaution when moving the product .................................................... 5

4. Cabinet diagram and maximum door opening ....................................... 5

5. Refrigerator/Freezer door opening and how to fix at 90 degrees ............. 6

6. Installation of part to prevent the product from falling over..................... 6

7. Connecting power and securing space for water supply pipe.................. 8

8. How to install the water supply pipe ...................................................... 9

9. Product detail dimension...................................................................... 10

10. Cabinet detail dimension.................................................................... 11

11. How to adjust the height of the refrigerator and freezer door .............. 12

12. How to adjust the height of the product.............................................. 13

13. How to disassemble/reassemble the top grill ...................................... 14

14. Left/Right door adjuster for refrigerator and freezer ............................ 15

Precaution

■ Install the product away from the heat of the heater, boiler or direct sunlight.

Install the product where air flows well and is well ventilated.

■ Refer to the dimension of the cabinet and prepare the cabinet with good air circulation.

Install the product so that air flows smoothly through the front air inlet. If the air circulation

structure is not ensured, it may interfere with the normal operation of the product.

■ Because the damage to the power cord from external animals (Rodents) can cause a

fire, install the product where there is no access from external animals.

■ If the cabinet is made of soft material (Ex: Plaster etc.), it can have week assembly force

or even can be damaged. Therefore use the cabinet made of firm strong material.

■ Use cabinet without any twisting from the heat emitted from the product or humidity from

the opening and closing of the refrigerator.

■ Install the product where it is leveled horizontally and vertically. (Within 1mm horizontally

and vertically) If the product is not leveled horizontally and vertically, it can be difficult to

install the product. (The cabinet must be made of material or must be in the structure not

to cause continuous deformation when 220.5 lb(100kg) of load is applied.)

■ Install the built-in refrigerator with a team of 2 people.

■ When installing the product, protect the children from the use of parts and installation

location.

■ During the installation, take out the screw from the plastic bag one by one to avoid any

injury from exposed parts.

■ Avoid the use of multi-tab as it can cause a fire.

■ Before installing the product, connect the product to make sure to check it is operating

normally.

WARNING

TIP-OVER HAZARD

Use two or more people to move and install the refrigerator.

To prevent the refrigerator from tipping over, install anti-tip brackets

(provided). Failure to follow the refrigerator installation instructions

can result in serious injury or death.

1. Precaution before installation

2. Product and Cutout dimension

- Product dimension (In) : 42”(1,067mm) x 83-1/2”(2,121mm) x 25-3/8”(645mm) (W x H x D)

- Cutout dimension for product installation (In)

41-1/2”(1,054mm) X 83-3/4”(2,127mm) X 24”(610mm) (W x H x D)

Width of cutout

41-1/2”(1,054mm)

View from front

Depth of cutout

View from top

24”(610mm)

Depth of

cutout

24”(610mm) Height of cutout

83-3/4”(2,127mm)

View from side

Check the dimension of the cutout to install the product against the dimension stated in the

installation manual. The dimensions are the recommended dimensions to install the product. (If

the cutout dimension is smaller than the recommended dimension, the product cannot be

installed.)

Depth from back of product to door

25-3/8”(645mm)

Width of back of product

41”(1,041mm)

Height of back of product

83-3/8”(2,116mm)

Height from floor to very top of the

front of the product

83-1/2”(2,121mm)

Width of front of product (Including left and right wing)

42”(1,067mm)

■. Before moving the refrigerator, check the line of movement to the location to install.

(Refer to the product dimension and rotating radius.)

3. Precaution when moving the product

1) Request the installation to the specialized technician.

It can cause electric shock, fire, malfunction and explosion.

2) Due to the characteristics of the built-in product, the top is heavy and can easily fall over when not

installed. Therefore be careful when moving the product. Also because the product can be

dangerous if left on inclined surface, always keep the product fixed or held.

4. Cabinet diagram and maximum door opening

< Dimension when opening 90 degrees >

When installing the product on the wall near the corner, check the marked dimension to

keep minimum distance to avoid the handle hitting the wall.

< Dimension when opening 130 degrees >

41”(1,041mm) 41”(1,041mm)

45-3/5”(1158mm) 68-1/2”(1739mm)

2-1/2”

(63mm)

2-1/2”

(63mm)

41-9/16”

(1,056mm)

44-1/2”

(1,130mm)

19”

(485mm)

16”

(409mm)

11-1/2”

(293mm)

(Unit : In)

16-3/16”

(411mm)

48-5/16”

(1,227mm)

23”

(582mm)

39-3/8”

(1,000mm)

14”

(355mm)

86”

(2,187mm)

86”

(2,187mm)

92-13/16”

(2,357mm)

92-13/16”

(2,357mm)

5. Refrigerator/Freezer door opening and how to

fix at 90 degrees

6. Installation of part to prevent the product from

falling over

※ Because the built-in product is heavy on the top, the

cabinet must be fixed firmly so that the product does not

move when using it.

• Fix the side of the cabinet to the building wall or side

of the furniture firmly.

• Use the part included in the accessory box as shown

in the picture to fix the cabinet to both sides of the

walls.

• If the part prevent the product from falling over is not

installed in the correct location, the product can fall

over to cause severe injury or death.

※ If the device to keep the refrigerator door

open and fixed cannot be inserted, move

the refrigerator door slowly in left and

right direction to push it in.

Part to prevent product

from falling over x 2

M4*L12 screw x 6 M4*L22 screw x 8

Push and install the device to keep the

refrigerator door open and fixed, included

in the accessory box, to the hole marked

on the picture completely.

The left and right side are installed in the

same method.

83-3/4”

(2,126mm)

83-3/4”

(2,126mm)

6. Installation of part to prevent the product from

falling over

1) Check if all the described parts are included in the accessory box.

2) Based on the recommended dimension on the picture, place the part to prevent the

product from falling over. (Same for both left and right side)

3) Use the M4*L12 screw included in the accessory box to tighten 3 locations respectively on

left and right side.

(Tighten the screws completely so that the part is not loose from the cabinet.)

4) Place the product on the cabinet and then use the M4*L22 screw included in the

accessory box to tighten 4 locations respectively on left and right side on the groove

marked on the picture after checking whether the product is leveled and checking the level

difference between the refrigerator and freezer door and the alignment between the front

part of the product against the cabinet etc.

(When inserting the refrigerator in the cabinet, be careful not to get the hand caught.)

Top groove Bottom groove

< Example of installation > < Example of installation >

4”

(100mm)

83-3/4”

(2,126mm)

< Use the M4*L12 Screw for xing

anti tip over bracket. >

< Use the M4*L22 Screw for xing Product. >

-. Power connection

The location of the 115V 60Hz power

connector must be located on the

rear side of the product as shown in

the picture.

When installing the product, make

sure to check whether the cord is

hung on the hook on the rear side

so that it is not pressed on the

refrigerator. Damaged power cord

can cause a fire.

- Installation space for water supply pipe

Place the water hose for ice

maker and water dispenser as

shown in the picture, and

prepare hose to come up from

the floor.

(Copper pipe with diameter of

5/16”(8mm) is recommended

for the water hose.)

If the water pipe and water

hose is located far from the

product, bury the water hose

on the floor and provide

appropriate treatment.

7. Connecting power and securing space for

water supply pipe

1/2”

(10mm)

3-3/16”

(81mm) 2-3/4”

(70mm)

19-1/4”

(489.5mm)

6-1/8”

(155mm)

1”

(25.5mm)

(Unit : In)

8-1/2”(220mm)

6”

(152mm)

5-3/4”

(147mm)

5-3/4”

(147mm)

Recommended

space for power

connector

Exposed space for water

supply pipe

Make sure the location of the water supply pipe is within the marked range.

Before connecting the power, always make sure to ground the product. (If the product is

not grounded, the user may be able to feel the electricity due to the minute leakage

current when touching the refrigerator door handle or side corner even when there is no

issue with the product.)

Do not ground the product to gas pipe, plastic water pipe or telephone wire etc. It can

cause electric shock and explosion.

Height from floor

70-1/2”

(1,790mm)

Height from floor

70-1/2”

(1,790mm)

1) Disassemble the bottom grill.

(Both the left and right sides are disassembled and

reassembled in the same method.)

- Use the (+) driver to disassemble the bottom grill.

2) Pull out the water supply pipe from the bottom of the

product and prepare to disassemble/reassemble the

connecting part of the water service pipe.

4) Reassemble the bottom grill in the reverse order of 1).

5) Flush air from the system by running water through the dispenser

continuously for 5 gallon.

Note: Allow 1~2 minute delay in water dispersal to allow internal

water tank to fill.

8. How to install the water supply pipe

※ Check the location and installation detail of the water

service pipe on the previous page before connecting the

water supply pipe. Before inserting the product completely

into the cabinet, check if there is any water leakage.

3) After connecting the water supply pipe and the water service

pipe, tighten them with a spanner to avoid any leakage. After

installing the product within the cabinet, recheck for any

water leakage.

※ Prepare a bucket under the water service pipe connector before checking for any water

leakage to avoid ruining the flooring material and carpet etc.

9. Product detail dimension

82-1/2”

(2,098mm)

83-1/2”

(2,121mm)

41”(1,041mm)

25-3/8”

(645mm)

27-7/8” (708mm)

Depth from front of

product to handle

Total height

of product

83-1/2”

(2,121mm)

Front width (Including wing)

42”(1,067mm)

Product height

excluding front

air inlet

82-1/2”

(2,098mm)

Depth from front to

back of product

Depth from front to

back of product

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Signature Kühlschrank Handbücher

Signature

Signature SRUS5000XAQUA Bedienungsanleitung

Signature

Signature SFDOOR5291XAQUA Bedienungsanleitung

Signature

Signature SRB4200XNF Bedienungsanleitung

Signature

Signature SRB4003A+X AQUA Bedienungsanleitung

Signature

Signature S30008 Montageanleitung

Signature

Signature SFDOOR4000XNF Bedienungsanleitung

Signature

Signature SDP3101A+ Bedienungsanleitung

Signature

Signature SKSFD4826P Bedienungsanleitung

Signature

Signature SRB3000A++X Bedienungsanleitung

Signature

Signature SFDOOR482BGNF Bedienungsanleitung

Signature

Signature SFDOOR5302XAQUA Bedienungsanleitung

Signature

Signature UPFXC2466 Series Bedienungsanleitung

Signature

Signature SRB3200A+XDN Bedienungsanleitung

Signature

Signature SRB4003A+X AQUA Bedienungsanleitung

Signature

Signature TABTOP SRT1004X Bedienungsanleitung

Signature

Signature SRB3103A+XNF Bedienungsanleitung

Signature

Signature S30003 Bedienungsanleitung

Signature

Signature UPFXC2466S Bedienungsanleitung

Signature

Signature SFDOOR483BGNF Bedienungsanleitung

Signature

Signature SKSCR2401P Bedienungsanleitung

Signature

Signature SRB4002A Bedienungsanleitung

Signature

Signature SFC3000STW Bedienungsanleitung

Signature

Signature SKSSB4202S Bedienungsanleitung

Signature

Signature SFDOOR362XNF Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung

Matsui

Matsui MTT50W12E Bedienungsanleitung